2014 Hilux · Service Manual TRANSMISSION

P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Diagnostic trouble codes · Vehicles built from Aug 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012

DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.
DTC Code
DTC Detection Conditions
Trouble Areas
P0705
2 or more switches are ON simultaneously for P (NSW), R, N (NSW), D, 2 or L positions (2 trip detection logic).
  1. Short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. ECM

MONITOR DESCRIPTION

The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
When the park/neutral position switch sends more than one signal at a time from switch positions P, R, N, D, 2 or L, the ECM interprets this as a fault in the switch. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C169725E20

INSPECTION PROCEDURE


HINT:
Using the Data List of the intelligent tester allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON and push the tester main switch on.
  5. Enter the following menus: Powertrain / Engine and ECT / Data List.
  6. Follow the instructions on the tester and read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Neutral Position SW Signal
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: In P or N
  2. OFF: Not in P or N
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (R Range)
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: In R
  2. OFF: Not in R
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (3 Range)
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: In 3
  2. OFF: Not in 3
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (2 Range)
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: In 2
  2. OFF: Not in 2
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (L Range)
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: In L
  2. OFF: Not in L
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.

NOTICE:
In the table above, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
When the malfunction is found when the shift lever is in 3, start from *1. When the malfunction is found when the shift lever is not in 3, start from *2.


1. INSPECT PARK/NEUTRAL POSITION SWITCH*1

  1. C146745E17
    Disconnect the N8 park/neutral position switch connector.

  1. Measure the resistance of the park/neutral position switch when the shift lever is moved to each position.

    Standard Resistance:
    Tester Connection
    Shift Lever Position
    Specified Condition
    4 (B) - 5 (L)
    P or N
    Below 1 Ω
    4 (B) - 5 (L)
    Not in P or N
    10 kΩ or higher
    1 (RL) - 2 (RB)
    R
    Below 1 Ω
    1 (RL) - 2 (RB)
    Not in R
    10 kΩ or higher
    2 (RB) - 7 (DL)
    D
    Below 1 Ω
    2 (RB) - 7 (DL)
    Not in D
    10 kΩ or higher
    2 (RB) - 3 (2L)
    2
    Below 1 Ω
    2 (RB) - 3 (2L)
    Not in 2
    10 kΩ or higher
    2 (RB) - 8 (LL)
    L
    Below 1 Ω
    2 (RB) - 8 (LL)
    Not in L
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH
OK


2. INSPECT SHIFT LOCK CONTROL ECU*2

  1. C170575E01
    Disconnect the S43 ECU connector.

  1. Measure the resistance of the ECU when the shift lever is moved to each position.

    Standard Resistance:
    Tester Connection
    Shift Lever Position
    Specified Condition
    9 (NSSD) - 3 (AT3)
    D
    10 kΩ or higher
    9 (NSSD) - 3 (AT3)
    3
    Below 1 Ω



NG
REPLACE SHIFT LOCK CONTROL ECU
OK


3. CHECK WIRE HARNESS (ECM - BATTERY)

  1. C192331E05
    Turn the ignition switch to ON.

  1. Measure the voltage of the wire harness side connector.

    Standard Voltage:
    Tester Connection
    Shift Lever Position
    Specified Condition
    E10-11 (R) - Body ground
    R
    11 to 14 V*
    E10-11 (R) - Body ground
    Not in R
    Below 1 V
    E10-19 (3) - Body ground
    D
    11 to 14 V
    E10-19 (3) - Body ground
    Not in D
    Below 1 V
    E10-10 (2) - Body ground
    2
    11 to 14 V
    E10-10 (2) - Body ground
    Not in 2
    Below 1 V
    E10-9 (L) - Body ground
    L
    11 to 14 V
    E10-9 (L) - Body ground
    Not in L
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to the illumination of the back-up light.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM


← P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (Jun 2011 – Jul 2012)P0710/38 Transmission Fluid Temperature Sensor "A" Circuit (+ P0712/38, P0713/38) (from Jun 2011) →