2014 Hilux · Service Manual TRANSMISSION

P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Diagnostic trouble codes · Vehicles built from Aug 2012

DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the TCM.
DTC Code
DTC Detection Condition
Trouble Area
P0705
One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic):
  1. NSW input signal
  2. R input signal
  3. D input signal
  4. 2 input signal
  5. L input signal
(B) All signals are OFF simultaneously for NSW, R, 2 and L positions (2-trip detection logic).
(C) Any of the following signals is ON for 2.0 seconds or more with the shift lever in 3 (2-trip detection logic):
  1. NSW input signal
  2. R input signal
  3. D input signal
  4. 2 input signal
  5. L input signal
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch assembly
  3. Shift lock control ECU (Shift lock control unit assembly)
  4. TCM

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the TCM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the TCM according to the shift lever position (R, D, 3, 2 or L).
The TCM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C241300E10

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the tester, read the Data List.

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    1. Shift lever in P or N: ON
    2. Shift lever not in P or N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    1. Shift lever in R: ON
    2. Shift lever not in R: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (2 Range)
    PNP switch status/
    ON or OFF
    1. Shift lever in 2: ON
    2. Shift lever not in 2: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (L Range)
    PNP switch status/
    ON or OFF
    1. Shift lever in L: ON
    2. Shift lever not in L: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    1. Shift lever in D or 3: ON
    2. Shift lever not in D or 3: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (3 Range)
    PNP switch status/
    ON or OFF
    1. Shift lever in 3: ON
    2. Shift lever not in 3: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.


1. CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)

  1. C253110E42
    Disconnect the park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N8-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V
    N8-2 (RB) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
  1. Disconnect the E5 ECM connector.

  1. C253110E43
    Disconnect the park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N8-4 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    N8-4 (B) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch Assembly)



NG
Go to step 7
OK


3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C197712E37
    Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (B) - 5 (L)
    Shift lever in P
    Below 1 Ω
    2 (RB) - 1 (RL)
    Shift lever in R
    Below 1 Ω
    4 (B) - 5 (L)
    Shift lever in N
    Below 1 Ω
    2 (RB) - 7 (DL)
    Shift lever in D or 3
    Below 1 Ω
    2 (RB) - 3 (2L)
    Shift lever in 2
    Below 1 Ω
    2 (RB) - 8 (LL)
    Shift lever in L
    Below 1 Ω
    4 (B) - 5 (L)
    Shift lever not in P
    10 kΩ or higher
    2 (RB) - 1 (RL)
    Shift lever not in R
    10 kΩ or higher
    4 (B) - 5 (L)
    Shift lever not in N
    10 kΩ or higher
    2 (RB) - 7 (DL)
    Shift lever not in D or 3
    10 kΩ or higher
    2 (RB) - 3 (2L)
    Shift lever not in 2
    10 kΩ or higher
    2 (RB) - 8 (LL)
    Shift lever not in L
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Park/Neutral Position Switch Assembly)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK


4. INSPECT SHIFT LOCK CONTROL ECU

  1. C214966E04
    Disconnect the shift lock control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (AT3) - 9 (NSSD)
    Shift lever in 3
    Below 1 Ω
    3 (AT3) - 9 (NSSD)
    Shift lever in D
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Shift Lock Control ECU)



NG
REPLACE SHIFT LOCK CONTROL ECU (SHIFT LOCK CONTROL UNIT ASSEMBLY)
OK


5. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL ECU)

  1. C203405E17
    Disconnect the shift lock control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S43-9 (NSSD) - Body ground
    1. Ignition switch ON
    2. Shift lever in D or 3
    11 to 14 V
    S43-9 (NSSD) - Body ground
    1. Ignition switch ON
    2. Shift lever not in D or 3
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Shift Lock Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)

  1. C212050E27
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T37-9 (R) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever in R
    11 to 14 V*
    T37-8 (D) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever in D
    11 to 14 V
    T37-12 (3) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever in 3
    11 to 14 V
    T37-11 (2) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever in 2
    11 to 14 V
    T37-10 (L) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever in L
    11 to 14 V
    T37-9 (R) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever not in R
    Below 1 V
    T37-8 (D) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever not in D
    Below 1 V
    T37-12 (3) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever not in 3
    Below 1 V
    T37-11 (2) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever not in 2
    Below 1 V
    T37-10 (L) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever not in L
    Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (TCM)

    HINT:
    *: The voltage will drop slightly due to the illumination of the back-up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM

7. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
  1. Disconnect the N8 park/neutral position switch connector.

  1. Disconnect the T19 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N8-4 (B) - T19-12 (NSW)
    Always
    Below 1 Ω
    N8-4 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM


← P0617 Starter Relay Circuit High (from Aug 2012)P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input (+ P0713) (from Aug 2012) →