2014 Hilux · Service Manual TRANSMISSION

P0973 Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1)

Diagnostic trouble codes · Vehicles built from Aug 2012

Also covers:

DESCRIPTION

Shifting from 1st to 4th is performed in combination with the on and off operation of shift solenoid valves S1 and S2, which are controlled by the TCM. If an open or short circuit occurs in either of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valve to allow the vehicle to be operated safely. Also, the TCM stops sending current to the open or short-circuited solenoid (Click here).
DTC Code
DTC Detection Condition
Trouble Area
P0973
TCM detects a short in the solenoid valve S1 circuit 4 times when solenoid valve S1 is operated (1-trip detection logic).
  1. Short in shift solenoid valve S1 circuit
  2. Shift solenoid valve S1
  3. TCM
P0974
TCM detects an open in the solenoid valve S1 circuit 4 times when solenoid valve S1 is not operated (1-trip detection logic).
  1. Open in shift solenoid valve S1 circuit
  2. Shift solenoid valve S1
  3. TCM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve S1 circuit. When there is an open or short circuit in either shift solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores the DTC. When shift solenoid valve S1 is on, if its resistance is 8 Ω or less, the TCM determines there is a short in the shift solenoid valve S1 circuit.
When shift solenoid valve S1 is off, if its resistance is 100 kΩ or higher, the TCM determines there is an open in the shift solenoid valve S1 circuit (Click here).

WIRING DIAGRAM

C214968E38

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE S1)

  1. C214964E02
    Disconnect the transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (S1) - Body ground
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

  1. C274533E31
    Disconnect the TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T19-18 (S1) - Body ground
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to TCM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM

3. INSPECT SHIFT SOLENOID VALVE S1

  1. C214962E01
    Remove shift solenoid valve S1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body
    20°C (68°F)
    11 to 15 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) → Shift solenoid valve S1 connector
    2. Battery negative (-) → Shift solenoid valve S1 body
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve S1)


NG
REPLACE SHIFT SOLENOID VALVE S1
OK

REPAIR OR REPLACE TRANSMISSION WIRE


← P0818 Driveline Disconnect Switch Input Circuit (from Aug 2012)P0976 Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2) (+ P0977) (from Aug 2012) →