2014 Hilux · Service Manual TRANSMISSION

P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)

Diagnostic trouble codes · Vehicles built from Jun 2011

DESCRIPTION

The amount of current flow to the solenoid is controlled by the duty ratio* of the ECM output signal. The higher the duty ratio becomes, the higher the lock-up hydraulic pressure becomes during the lock-up operation.
C110339E02
*: The duty ratio is the ratio of the current ON time (A) to the total of the current ON and OFF times (A + B).
Duty Ratio (%) = A/ (A + B) x 100
DTC No.
DTC Detection Condition
Trouble Area
P2759
Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1 trip detection logic)
  1. Open or short in shift solenoid valve SLU circuit
  2. Shift solenoid valve SLU
  3. ECM

MONITOR DESCRIPTION

When an open or short in a shift solenoid valve SLU circuit is detected, the ECM determines that there is a malfunction. The ECM will illuminate the MIL and store this DTC.

WIRING DIAGRAM

A110976E04

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)

  1. G020667E29
    Disconnect the E1 wire connector.

  1. Measure the resistance of the wire connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    13 (SLU+) - 5 (SLU-)
    20°C (68°F)
    5.0 to 5.6 Ω
    13 (SLU+) - Body ground
    20°C (68°F)
    10 kΩ or higher
    5 (SLU-) - Body ground
    20°C (68°F)
    10 kΩ or higher



NG
Go to step 3
OK


2. CHECK WIRE HARNESS (TRANSMISSION WIRE - ECM)

  1. G035616E09
    Disconnect the E16 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-15 (SLU+) - E16-14 (SLU-)
    20°C (68°F)
    5.0 to 5.6 Ω
    E16-15 (SLU+) - Body ground
    20°C (68°F)
    10 kΩ or higher
    E16-14 (SLU-) - Body ground
    20°C (68°F)
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM

3. INSPECT SHIFT SOLENOID VALVE SLU
G020767E16
  1. Remove the shift solenoid valve SLU.

  1. Measure the resistance of the solenoid valve.

    Standard resistance:
    5.0 to 5.6 Ωat 20°C (68°F)

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

  1. Check the operating noise of terminal 1 of the solenoid valve.

    OK:
    Solenoid makes operating noise.


    HINT:
    A110977E04
    Reference: Inspect using an oscilloscope.
    Check the waveform of the ECM connector.

    OK:
    Refer to illustration.
    Item
    Content
    Tester Connection
    E16-15 (SLU+) - E16-14 (SLU-)
    Tool Setting
    5 V/DIV., 1 msec./DIV.
    Condition
    4th (lock-up) or 5th (lock-up) gear



NG
REPLACE SHIFT SOLENOID VALVE SLU
OK

REPAIR OR REPLACE TRANSMISSION WIRE


← P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) (from Jun 2011)REPLACEMENT (from Jun 2011) →