2014 Hilux · Service Manual TRANSMISSION

P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012

DESCRIPTION

Refer to DTC P2714 (Click here).
DTC Code
DTC Detection Condition
Trouble Area
P2716
Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip detection logic)
  1. Open or short in shift solenoid valve SLT circuit
  2. Shift solenoid valve SLT
  3. ECM

MONITOR DESCRIPTION

When an open or short in the linear solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

A110976E29

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)

  1. G020667E27
    Disconnect the E1 wire connector.

  1. Measure the resistance of the wire connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    14 (SLT+) - 6 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    14 (SLT+) - Body ground
    20°C (68°F)
    10 kΩ or higher
    6 (SLT-) - Body ground
    20°C (68°F)
    10 kΩ or higher



NG
Go to step 3
OK


2. CHECK WIRE HARNESS (TRANSMISSION WIRE - ECM)

  1. G035616E08
    Disconnect the E16 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-13 (SLT+) - E16-12 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    E16-13 (SLT+) - Body ground
    20°C (68°F)
    10 kΩ or higher
    E16-12 (SLT-) - Body ground
    20°C (68°F)
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM

3. INSPECT SHIFT SOLENOID VALVE SLT
G020767E16
  1. Remove the shift solenoid valve SLT.

  1. Measure the resistance of the solenoid valve.

    Standard resistance:
    5.0 to 5.6 Ω at 20°C (68°F)

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

  1. Check the operating noise of the solenoid valve.

    OK:
    Solenoid makes operating noise.


    HINT:
    A110977E03
    Reference: Inspect using an oscilloscope.
    Check the waveform of the ECM connector.

    OK:
    Refer to illustration.
    Item
    Content
    Tester Connection
    E16-13 (SLT+) - E16-12 (SLT-)
    Tool Setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Engine is idling



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK

REPAIR OR REPLACE TRANSMISSION WIRE


← P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) (from Aug 2012)P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) (from Aug 2012) →