2014 Hilux · Service Manual TRANSMISSION

P0985 Shift Solenoid "E" Control Circuit Low (Shift Solenoid Valve SR)

Diagnostic trouble codes · Vehicles built from Jun 2011

Also covers:

DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2 and SR, which is controlled by the ECM. If an open or short circuit occurs in the shift solenoid valves, the ECM controls the remaining normal shift solenoid valve to allow the vehicle to be operated safely (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P0985
ECM detects short in solenoid valve SR circuit 2 times when solenoid valve SR is operated (1 trip detection logic)
  1. Short in shift solenoid valve SR circuit
  2. Shift solenoid valve SR
  3. ECM
P0986
ECM detects open in solenoid valve SR circuit 2 times when solenoid valve SR is not operated (1 trip detection logic)
  1. Open in shift solenoid valve SR circuit
  2. Shift solenoid valve SR
  3. ECM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve SR circuit. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem and illuminates the MIL and stores the DTC. When the shift solenoid valve SR is ON, if resistance is 8 Ω or less, the ECM determines that there is a short in the shift solenoid valve SR circuit.
When the shift solenoid valve SR is OFF, if resistance is 100 kΩ or more, the ECM determines that there is an open in the shift solenoid valve SR circuit (Click here).

WIRING DIAGRAM

A110993E03

INSPECTION PROCEDURE


HINT:
The shift solenoid valve SR turns ON/OFF normally when the shift lever is on D:
ECM gear shift command
1st
2nd
3rd
4th
5th
Shift solenoid valve SR
OFF
OFF
OFF
OFF
ON


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SR)

  1. G020667E26
    Disconnect the E1 wire connector.

  1. Measure the resistance of the wire connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    7 (SR) - Body ground
    20°C (68°F)
    11 to 15 Ω



NG
Go to step 3
OK


2. CHECK WIRE HARNESS (TRANSMISSION WIRE - ECM)

  1. G035616E07
    Disconnect the E16 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-9 (SR) - Body ground
    20°C (68°F)
    11 to 15 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM

3. INSPECT SHIFT SOLENOID VALVE SR
A110988E01
  1. Remove the shift solenoid valve SR.

  1. Measure the resistance of the solenoid valve.

    Standard resistance:
    11 to 15 Ωat 20°C (68°F)

  1. Connect the battery's positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

  1. Check the operating noise of the solenoid valve.

    OK:
    Solenoid makes operating noise.



NG
REPLACE SHIFT SOLENOID VALVE SR
OK

REPAIR OR REPLACE TRANSMISSION WIRE


← P0976 Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2) (+ P0977) (from Jun 2011)P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) (Jun 2011 – Jul 2012) →