P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012
Also covers:
- P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)
- P0051 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)
- P0052 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)
Versions by build date: Jun 2011 – Jul 2012 from Aug 2012
DESCRIPTION
Refer to DTC P2195 (Click here).- HINT:
- When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned OFF.
- The ECM uses a pulse width modulated control circuit to adjust the current through the heater. The A/F sensor heater circuit uses a relay on the +B side of the circuit.


- When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned OFF.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0031 P0051 |
Heated current is 0.8 A or less when heater operates (bank 1) (1 trip detection logic) |
|
| P0032 P0052 |
Heated current exceeds 10 A when heater operates (bank 2) (1 trip detection logic) |
|
- HINT:
- Bank 1 refers to the bank that includes the No. 1 cylinder.
- Bank 2 refers to the bank that does not include the No. 1 cylinder.
- Sensor 1 refers to the sensor closest to the engine assembly.
- Sensor 2 refers to the sensor farthest away from the engine assembly.
- Bank 1 refers to the bank that includes the No. 1 cylinder.
MONITOR DESCRIPTION
The ECM uses A/F sensor information to keep the air-fuel ratio close to the stoichiometric ratio. This maximizes the catalytic converter's ability to purify exhaust gases. The sensor detects oxygen levels in the exhaust gas and sends this signal to the ECM.The inner surface of the sensor element is exposed to outside air. The outer surface of the sensor element is exposed to exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element. The zirconia element generates a small voltage when there is a large difference in the oxygen concentration of the exhaust and outside air. The platinum coating amplifies the voltage generation. When the sensor is heated, the sensor becomes very efficient. If the temperature of the exhaust is low, the sensor will not generate useful voltage signals without supplemental heating. The ECM regulates the supplemental heating using a duty-cycle approach to regulate the average current in the heater element.
If the heater current is out of the normal operating range, the sensor's output signals will be inaccurate and the ECM cannot regulate the A/F properly.
When the heater current is out of the normal operating range, the ECM interprets this as a malfunction and sets a DTC.
WIRING DIAGRAM
Refer to DTC P2195 (Click here).INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- Although "oxygen sensor" is in the DTC titles, these DTCs are related to the air-fuel ratio (A/F) sensor.
- Sensor 1 refers to the sensor mounted before the Three-Way Catalytic Converter (TWC) and is located near the engine assembly.
- Sensor 2 refers to the sensor mounted after the TWC and is located far from the engine assembly.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() ![]() |
Disconnect the A/F sensor connector.
Measure the resistance of the A/F sensor.
- Standard resistance (Bank 1 Sensor 1):
Tester Connection
Condition
Specified Condition
1 (HA1A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω
1 (HA1A) - 4 (A1A-)
-
10 kΩ or higher
- Standard resistance (Bank 2 Sensor 1):
Tester Connection
Condition
Specified Condition
1 (HA2A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω
1 (HA2A) - 4 (A2A-)
-
10 kΩ or higher
|
|
||||
| OK | |
| 2. INSPECT RELAY (Marking: A/F) |
![]() ![]() |
Remove the A/F heater relay from the engine room relay block.
Measure the resistance of the relay.
- Standard resistance:
Terminal No.
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)
|
|
||||
| OK | |
| 3. INSPECT ECM (HA1A AND HA2A VOLTAGE) |
![]() ![]() |
Turn the ignition switch ON.
Measure the voltage of the E16 and E17 ECM connectors.
- Standard voltage:
Tester Connection
Specified Condition
E16-2 (HA1A) - E17-1 (E1)
9 to 14 V
E16-1 (HA2A) - E17-1 (E1)
9 to 14 V
|
|
||||
| NG | |
| 4. CHECK WIRE HARNESS (A/F SENSOR - ECM AND A/F RELAY) |
![]() ![]() |
Disconnect the A18 and A25 A/F sensor connectors.
Disconnect the E16 ECM connector.
Remove the A/F relay from the engine room relay block.
Measure the resistance of the wire harness side connectors.
- Standard resistance (Bank 1 Sensor 1):
Tester Connection
Specified Condition
A18-1 (HA1A) - E16-2 (HA1A)
Below 1 Ω
A18-2 (+B) - Relay block A/F relay terminal 3
Below 1 Ω
A18-1 (HA1A) or E16-2 (HA1A) - Body ground
10 kΩ or higher
A18-2 (+B) or relay block A/F relay terminal 3 - Body ground
10 kΩ or higher
- Standard resistance (Bank 2 Sensor 1):
Tester Connection
Specified Condition
A25-1 (HA2A) - E16-1 (HA2A)
Below 1 Ω
A25-2 (+B) - Relay block A/F relay terminal 3
Below 1 Ω
A25-1 (HA2A) or E16-1 (HA2A) - Body ground
10 kΩ or higher
A25-2 (+B) or relay block A/F relay terminal 3 - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||




