INSPECTION
Inspection · Vehicles built from Jun 2011
| INSPECT VANE PUMP SHAFT AND BUSHING IN FRONT HOUSING |
Using a micrometer, measure the diameter (a) of the vane pump shaft.

Using a caliper gauge, measure the inside diameter (b) of the front housing.
- NOTICE:
- Do not damage the bushing in the front housing.
Subtract (a) from (b) to calculate the oil clearance.
- Maximum oil clearance:
- 0.07 mm (0.0028 in.) or less
| INSPECT VANE PUMP ROTOR AND VANE PUMP PLATES CLEARANCE |
Using a feeler gauge, measure the clearance between the side face of the vane pump rotor groove and the vane pump plates.

- Maximum clearance:
- 0.03 mm (0.0012 in.)
- NOTICE:
- If the clearance is more than the maximum, replace the vane pump plates, vane pump rotor and vane pump cam ring.
- Refer to the following table to select an appropriate combination of vane pump rotor, vane pump cam ring and vane pump plates.
- Combination of vane pump rotor, vane pump cam ring and vane pump plates:
for 2WD Vane Pump Rotor Part No.
Vane Pump Cam Ring Part No.
Vane Pump Plate Part No.
44313-02160
44325-0K060
44345-06060
44313-02170
44325-0K070
44345-06070
44313-02180
44325-0K080
44345-06080
44313-02190
44325-0K090
44345-06090
44313-02200
44325-0K100
44345-06100
for 4WD Vane Pump Rotor Part No.
Vane Pump Cam Ring Part No.
Vane Pump Plate Part No.
44313-02160
44325-06110
44345-06060
44313-02170
44325-06120
44345-06070
44313-02180
44325-06130
44345-06080
44313-02190
44325-06140
44345-06090
44313-02200
44325-06150
44345-06100
- If the clearance is more than the maximum, replace the vane pump plates, vane pump rotor and vane pump cam ring.
| INSPECT FLOW CONTROL VALVE |
Check the flow control valve for leakage. Close one of the holes and apply compressed air, 392 to 490 kPa (4 to 5 kgf/cm2, 57 to 71 psi), into the opposite side hole, and confirm that air does not come out from the end holes.

- NOTICE:
- Make sure to use clean and dry air.
If there is leakage, replace the flow control valve.

- NOTICE:
- Check the mark on the front housing and replace the flow control valve with one having the same mark as that of the front housing.
- Refer to the following table to select an appropriate combination of front housing and flow control valve.
- Combination of front housing and flow control valve:
Front Housing Mark
Flow Control Valve Mark
Flow Control Valve Part No.
A
A
44330-04010
B
B
44330-04020
C
C
44330-04030
D
D
44330-04040
E
E
44330-04050
F
F
44330-04060
- Check the mark on the front housing and replace the flow control valve with one having the same mark as that of the front housing.
Coat the flow control valve with power steering fluid.
- NOTICE:
- Make sure to use new power steering fluid.
Insert the flow control valve into the flow control valve installation hole of the front housing, and check that the flow control valve enters smoothly under its own weight.
If the flow control valve does not enter the front housing smoothly, replace the flow control valve.
| INSPECT FLOW CONTROL VALVE COMPRESSION SPRING |
Using a vernier caliper, measure the free length of the flow control valve compression spring.

- Minimum free length:
- 32.3 mm (1.272 in.)
| INSPECT PRESSURE PORT UNION |
If the union seat in the pressure port union is severely damaged, replace the pressure port union.
