2014 Hilux · Service Manual BRAKE

DTC CHECK / CLEAR

Troubleshooting · Vehicles built Jun 2011 – Jul 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013


DTC CHECK/CLEAR (When Using Intelligent Tester)
  1. Check for DTCs.

    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the intelligent tester on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.

    6. Check the details of the DTCs.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

  2. Clear the DTCs.

    NOTICE:
    Clearing the DTC also clears the freeze frame data.


    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the intelligent tester on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.

    6. Clear the DTCs by following the prompts on the intelligent tester.

      HINT:
      Refer to the intelligent tester operator's manual for further details.


DTC CHECK/CLEAR (When Using SST Check Wire)

  1. C146309E17
    Check for DTCs.
    Text in Illustration  
    *a
    Front view of DLC3

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

    2. Turn the ignition switch to ON.

    3. Read the DTCs output from the ABS warning light and VSC OFF indicator light in the combination meter.

      HINT:
      1. When the system is normal, the ABS warning light and VSC OFF indicator light blink at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).
      2. When only 1 DTC is output, the light outputs the same code after an interval of 4 seconds. Example: when DTC 21 is output, the light blinks twice, turns off for 1.5 seconds, blinks once, turns off for 4 seconds, and then repeats this output pattern.
      3. When 2 or more DTCs are output, the light outputs the codes with an interval of 2.5 seconds between each different code, and it repeats the output of all codes after an interval of 4 seconds.

    4. Warning and indicator light codes are defined in the following charts.

      ABS DTC 
      ABS Warning Light Display
      DTC Code
      11
      C0278
      12
      C0279
      13
      C0273
      14
      C0274
      21
      C0226
      22
      C0236
      23
      C0246
      24
      C0256
      25
      C1225
      31
      C1401
      C1405
      32
      C1402
      C1406
      33
      C1403
      C1407
      34
      C1404
      C1408
      35
      C1413
      36
      C1414
      37
      C1337
      38
      C1415
      39
      C1416
      41
      C1241
      C1417
      43
      C1243
      44
      C1419
      C1420
      C1442
      45
      C1245
      46
      C1421
      C1422
      C1423
      C1424
      49
      C1425
      C1426
      51
      C1427
      C1428
      67
      C1429
      C1430
      C1431
      68*
      C1268*
      91
      C1361
      94
      U0073
      95
      U0124
      97
      C1381
      1. *: for 4WD
      VSC DTC 
      VSC OFF Indicator Light Display
      DTC Code
      31
      C1432
      C1433
      C1434
      32
      C1232
      34
      C1435
      C1436
      C1443
      36
      C1210
      39
      C1336
      43*
      -
      51
      C1201
      53
      C1203
      62
      U0123
      63
      U0126
      65
      C1437
      U0100
      66
      C1290
      C1439
      C1445
      98
      C1440
      C1441
      1. *: This DTC is stored when the VSC system detects a malfunction in the ABS.

    5. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

      HINT:
      If 2 or more DTCs are output at the same time, the DTCs are output in ascending order.

  2. Clear the DTCs.

    1. C146309E17
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      Text in Illustration  
      *a
      Front view of DLC3
      SST
      09843-18040  

    2. Turn the ignition switch to ON.

    3. Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.

    4. Check that the ABS warning light and VSC OFF indicator light blink at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).

    5. Remove SST from the terminals of the DLC3.


END OF DTC CHECK/CLEAR
  1. Turn the ignition switch to ON.

  2. Check that the ABS warning light and VSC OFF indicator light go off within approximately 3 seconds after turning the ignition switch to ON.

← DIAGNOSIS SYSTEM (from Aug 2013)DTC CHECK / CLEAR (from Aug 2013) →