DATA LIST / ACTIVE TEST
System information · Vehicles built Jun 2011 – Jul 2013
Versions by build date: Jun 2011 – Jul 2013 from Aug 2013
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the tester, read the Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ABS Warning Light
ABS warning light / ON or OFF
ON: ABS warning light on
OFF: ABS warning light off
-
VSC Warning Light
VSC OFF indicator light / ON or OFF
ON: VSC OFF indicator light on
OFF: VSC OFF indicator light off
-
Brake Warning Light
Brake warning light / ON or OFF
ON: Brake warning light on
OFF: Brake warning light off
-
Slip Indicator Light
Slip indicator light / ON or OFF
ON: Slip indicator light on
OFF: Slip indicator light off
-
Stop Light SW
Stop light switch / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW
Parking brake switch / ON or OFF
ON: Parking brake applied
OFF: Parking brake released
-
Main Idle SW
Main idle switch / ON or OFF
ON: Accelerator pedal released
OFF: Accelerator pedal depressed
-
Brake Pedal Load Sensing SW
Brake pedal load sensing switch / ON or OFF
ON: Brake pedal depressed beyond specified point
OFF: Brake pedal not depressed beyond specified point
-
Gear Position
Gear position information / P,N, R, 1st-8th, Fail, Not R
Actual gear position
-
Shift Lever Position
Shift lever position information / P,N, R, D/M, 1st-6th/B, Fail
Actual shift lever position
-
Shift Information
Shift information / ON or OFF
ON: During gear change
OFF: Not during gear change
-
Inspection Mode
Inspection mode / Other or Inspect
Other: Normal mode
Inspect: Inspection mode
-
Number of IG ON (Inspection)
Number of times ignition switch turned on after entering inspection mode / Min.: 0, Max.: 255
-
-
Master Cylinder Sensor
Master cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V
When brake pedal released: 0.3 to 0.9 V
The value increases when the brake pedal is depressed.
Zero Point of M/C
Memorized zero value / Min.: -12.50 Mpa, Max.: 12.40 Mpa
-
-
Deceleration Sensor
Acceleration sensor (GL1) / Min.: -18.525 m/s2, Max.: 18.387 m/s2
-
Changes continuously during acceleration/deceleration.
Zero Point of Decele
Memorized zero value / Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
-
Deceleration Sensor2
Acceleration sensor (GL2) / Min.: -18.525 m/s2, Max.: 18.387 m/s2
-
Changes continuously during acceleration/deceleration.
Zero Point of Decele2
Memorized zero value / Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
-
Yaw Rate Sensor
Yaw rate sensor / Min.: -128°/s, Max.: 127°/s
Vehicle stationary: 0°/s
Right turn: -128 to 0°/s
Left turn: 0 to 127°/s
-
Zero Point of Yaw Rate
Memorized zero value / Min.: -128°, Max.: 127°
-
-
Yaw Rate Sensor2
Yaw rate sensor 2 / Min.: -128°/s, Max.: 127°/s
Vehicle stationary: 0°/s
Right turn: -128 to 0°/s
Left turn: 0 to 127°/s
-
Zero Point of Yaw Rate2
Memorized zero value / Min.: -128°/s, Max.: 127°/s
-
-
Steering Angle Sensor
Steering angle sensor / Min.: -3276.8°, Max.: 3276.7°
Left turn: Increases
Right turn: Decreases
-
Zero Point of Steering Angle
Memorized zero value / Min.: -3276.8°, Max.: 3276.7°
After steering angle sensor zero point calibration: 0°
-
Lateral G
Lateral G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
Changes in proportion to acceleration during turning.
Forward and Rearward G
Forward and backward G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
Changes in proportion to acceleration during acceleration/deceleration.
Yaw Rate Value
Yaw rate value / Min.: -128°/s, Max.: 127°/s
-
Changes in proportion to yaw during turning.
Steering Angle Value
Steering angle value / Min.: -3276.8°, Max.: 3276.7°
-
Changes in proportion to the amount of steering wheel rotation during steering operation.
Rear Diff Lock Switch
Rear differential lock position switch / ON or OFF
w/ Rear Differential Lock:
ON: Rear differential lock position switch on
OFF: Rear differential lock position switch off
w/o Rear Differential Lock:
OFF
-
Automatic Disconnect Diff SW
4WD detection switch / ON or OFF
ON: 4WD
OFF: 2WD
-
L4 Switch
L4 position switch / ON or OFF
ON: L4
OFF: except L4
-
FR Wheel Speed
Front speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
FL Wheel Speed
Front speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
RR Wheel Speed
Rear speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
RL Wheel Speed
Rear speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
Vehicle Speed
Maximum speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
No large fluctuations when driving at a constant speed.
FR Wheel Acceleration
Front wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
Changes continuously during acceleration/deceleration.
FL Wheel Acceleration
Front wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
Changes continuously during acceleration/deceleration.
RR Wheel Acceleration
Rear wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
Changes continuously during acceleration/deceleration.
RL Wheel Acceleration
Rear wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
Changes continuously during acceleration/deceleration.
FR Wheel ABS Ctrl Status
Front wheel RH ABS control status / ON or OFF
ON: During control
OFF: Not during control
-
FL Wheel ABS Ctrl Status
Front wheel LH ABS control status / ON or OFF
ON: During control
OFF: Not during control
-
RR Wheel ABS Ctrl Status
Rear wheel RH ABS control status / ON or OFF
ON: During control
OFF: Not during control
-
RL Wheel ABS Ctrl Status
Rear wheel LH ABS control status / ON or OFF
ON: During control
OFF: Not during control
-
RR Wheel EBD Ctrl Status
Rear wheel RH EBD control status / ON or OFF
ON: During control
OFF: Not during control
-
RL Wheel EBD Ctrl Status
Rear wheel LH EBD control status / ON or OFF
ON: During control
OFF: Not during control
-
BA Ctrl Status
BA control status / ON or OFF
ON: During control
OFF: Not during control
-
TRC(TRAC) Ctrl Status
TRC control status / ON or OFF
ON: During control
OFF: Not during control
-
TRC(TRAC) Engine Ctrl Status
TRC engine control status / ON or OFF
ON: During control
OFF: Not during control
-
TRC(TRAC) Brake Ctrl Status
TRC brake control status / ON or OFF
ON: During control
OFF: Not during control
-
FR Wheel VSC Ctrl Status
Front wheel RH VSC control status / ON or OFF
ON: During control
OFF: Not during control
-
FL Wheel VSC Ctrl Status
Front wheel LH VSC control status / ON or OFF
ON: During control
OFF: Not during control
-
RR Wheel VSC Ctrl Status
Rear wheel RH VSC control status / ON or OFF
ON: During control
OFF: Not during control
-
RL Wheel VSC Ctrl Status
Rear wheel LH VSC control status / ON or OFF
ON: During control
OFF: Not during control
-
Engine Revolutions
Engine speed / Min.: 0 rpm, Max.: 65535 rpm
Engine stopped: 0 rpm
No large fluctuations when the engine speed is constant.
Real Engine Torque
Actual engine torque / Min.: -1024.0 Nm, Max.: 1023.0 Nm
-
-
Accelerator Opening Angle %
Throttle valve opening amount / Min.: 0.0%, Max.: 128.0%
When accelerator pedal released: 0%
Changes in proportion to the movement of the pedal during accelerator pedal operation.
Solenoid Relay
Solenoid relay / ON or OFF
ON: Solenoid relay on
OFF: Solenoid relay off
-
ECB* Motor Relay
Motor relay / ON or OFF
ON: Motor relay on
OFF: Motor relay off
-
Fail Safe Motor Relay
Motor fail-safe relay / ON or OFF
ON: Motor fail-safe relay on
OFF: Motor fail-safe relay off
-
TR(A)C/VSC Solenoid (SM2)
Master cylinder cut solenoid (SM2) / ON or OFF
ON: Operating
OFF: Not operating
-
TR(A)C/VSC Solenoid (SM1)
Master cylinder cut solenoid (SM1) / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFRH)
Front wheel RH hold solenoid / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFRR)
Front wheel RH release solenoid / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFLH)
Front wheel LH hold solenoid / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFLR)
Front wheel LH release solenoid / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRRH)
Rear wheel RH hold solenoid / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRRR)
Rear wheel RH release solenoid / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRLH)
Rear wheel LH hold solenoid / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRLR)
Rear wheel LH release solenoid / ON or OFF
ON: Operating
OFF: Not operating
-
FR Speed Open
Front speed sensor RH open circuit detection / Error or Normal
Normal
-
FL Speed Open
Front speed sensor LH open circuit detection / Error or Normal
Normal
-
RR Speed Open
Rear speed sensor RH open circuit detection / Error or Normal
Normal
-
RL Speed Open
Rear speed sensor LH open circuit detection / Error or Normal
Normal
-
EFI Communication Open
EFI communication open circuit detection / Error or Normal
Normal
-
Yaw Rate Open
Yaw rate sensor open circuit detection / Error or Normal
Normal
-
Deceleration Open
Acceleration sensor open circuit detection / Error or Normal
Normal
-
Steering Open
Steering angle sensor open circuit detection / Error or Normal
Normal
-
Master Cylinder Open
Master cylinder pressure sensor open circuit detection / Error or Normal
Normal
-
IG1 Voltage Value
IG1 voltage / Min.: 0.00 V, Max.: 20.00 V
11 to 14 V
-
MT Voltage Value
Monitor voltage / Min.: 0.00 V, Max.: 20.00 V
-
TRC/VSC Off Mode
VSC OFF switch / Normal, Unknown, TRC OFF or VSC OFF
Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-
Number of DTC
Number of DTCs stored / Min.: 0, Max.: 255
-
-
IG Voltage Value Decreased
IG voltage value decrease detection / Error or Normal
Normal
-
IG Voltage Value Increased
IG voltage value increase detection / Error or Normal
Normal
-
FR Speed Sensor Voltage Open
Front speed sensor RH voltage open circuit detection / Error or Normal
Normal
-
FL Speed Sensor Voltage Open
Front speed sensor LH voltage open circuit detection / Error or Normal
Normal
-
RR Speed Sensor Voltage Open
Rear speed sensor RH voltage open circuit detection / Error or Normal
Normal
-
RL Speed Sensor Voltage Open
Rear speed sensor LH voltage open circuit detection / Error or Normal
Normal
-
M/C Pressure Sensor Noise
Master cylinder pressure sensor noise detection / Error or Normal
Normal
-
Brake Pedal Switch Open
Brake pedal load sensing switch open circuit detection / Error or Normal
Normal
-
Yaw Rate Sensor Voltage Open
Yaw rate sensor voltage open circuit detection / Error or Normal
Normal
-
EFI Communication Invalid
EFI communication invalid detection / Error or Normal
Normal
-
- *: Electronically Controlled Brake
- *: Electronically Controlled Brake
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
According to the display on the tester, perform the Active Test.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
ABS Warning Light
ABS warning light
Warning light ON / OFF
Observe the combination meter.
VSC Warning Light
VSC OFF indicator light
Indicator light ON / OFF
Observe the combination meter.
Brake Warning Light
Brake warning light
Warning light ON / OFF
Observe the combination meter.
Slip Indicator Light
Slip indicator light
Indicator light ON / OFF
Observe the combination meter.
Solenoid Relay
Solenoid relay
Relay ON / OFF
When Solenoid Relay is turned OFF using the Active Test, the slip indicator light turns on.
Motor Relay
Motor relay
Relay ON / OFF
The operating sound of the motor can be heard.
ABS Solenoid (SRLR)
Rear wheel LH release solenoid
Solenoid ON / OFF
The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRLH)
Rear wheel LH hold solenoid
Solenoid ON / OFF
The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRRR)
Rear wheel RH release solenoid
Solenoid ON / OFF
The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRRH)
Rear wheel RH hold solenoid
Solenoid ON / OFF
The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFLR)
Front wheel LH release solenoid
Solenoid ON / OFF
The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFLH)
Front wheel LH hold solenoid
Solenoid ON / OFF
The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFRR)
Front wheel RH release solenoid
Solenoid ON / OFF
The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFRH)
Front wheel RH hold solenoid
Solenoid ON / OFF
The operating sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SMR)
Master cylinder cut solenoid (SM2)
Solenoid ON / OFF
The operating sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SMF)
Master cylinder cut solenoid (SM1)
Solenoid ON / OFF
The operating sound of the solenoid (clicking sound) can be heard.