2014 Hilux · Service Manual ENGINE

P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built from Jun 2011

Also covers:

DESCRIPTION

The Air-fuel Ratio (A/F) sensor generates a voltage* in response to the actual air-fuel ratio. The sensor output voltage provides feedback to the ECM. The ECM uses the feedback to control the air-fuel ratio.
Using the sensor output voltage, the ECM determines the deviation from the stoichiometric air-fuel ratio, and regulates the injection time. If the A/F sensor is malfunctioning, the ECM is unable to control the air-fuel ratio accurately.
The A/F sensor is equipped with a heater which heats the zirconia element. The heater is also controlled by the ECM. When the intake air volume is low (the temperature of the exhaust gas is low), a current flows to the heater to heat the sensor to facilitate the accurate detection of oxygen concentration.
The A/F sensor is a planar type. The heat of the heater is conducted to the zirconia element through the alumina, accelerating sensor activation.
To obtain a high purification rate of carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) in the exhaust gas, the Three-Way Catalytic Converter (TWC) is used. The TWC is most efficient when the air-fuel ratio is maintained near the stoichiometric air-fuel ratio.

HINT:
  1. *: The voltage value changes inside the ECM only.
  2. These DTCs are related to the A/F sensor.

DTC No.
DTC Detection Condition
Trouble Area
P2237
Open in the circuit between terminals AF+ and AF- of the A/F sensor while engine is running
(2 trip detection logic)
  1. Open in Air Fuel Ratio (A/F) sensor (sensor 1) circuit
  2. Air Fuel Ratio (A/F) sensor (sensor 1)
  3. ECM
P2238
  1. Condition (a) or (b) continues for 5.0 seconds or more:
    (a) AF+ is 0.5 V or less
    (b) (AF+) - (AF-) is 0.1 V or less
  1. A/F sensor admittance: Less than 0.022 1/Ω
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM
P2239
  1. Condition (a) or (b) continues for 5.0 seconds or more:
    (a) AF+ is more than 4.5 V
    (b) (AF+) - (AF-) is more than 0.8 V
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM
P2252
AF- is 0.5 V or less for 5.0 seconds or more
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM
P2253
AF- is more than 4.5 V for 5.0 seconds or more
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM

WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the "Control the Injection Volume" function provided in the Active Test. The "Control the Injection Volume" function can help to determine whether the Air-fuel Ratio (A/F) sensor, heated oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the "Control the Injection Volume" operation using intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the intelligent tester ON.
  3. Warm up the engine by running the engine at 2,500 rpm for approximately 90 seconds.
  4. On the intelligent tester, select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
  5. Perform the "Control the Injection Volume" operation with the engine in an idling condition (press the right or left button to change the fuel injection volume).
  6. Monitor the output voltage of the A/F and Heated oxygen sensors (AFS B1 S1 and O2S B1 S2) displayed on the tester.

HINT:
  1. The "Control the Injection Volume" operation lowers the fuel injection volume by 12.5% or increases the injection volume by 24.8%.
  1. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Standard:
Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS B1S1 or AFS B1 S1
(A/F)
+24.8%
Rich
Less than 3.0 V
AFS B1S1 or AFS B1 S1
(A/F)
-12.5%
Lean
More than 3.35 V
O2S B1 S2
(HO2)
+24.8%
Rich
More than 0.55 V
O2S B1 S2
(HO2)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The A/F sensor output has a few seconds of delay and the heated oxygen sensor output has about 20 seconds of delay at maximum.

Case
A/F Sensor (Sensor 1)
Output Voltage
HO2 Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Areas
1
Injection Volume
+24.8%
-12.5%
A103184
Injection Volume
+24.8%
-12.5%
A103184
-
Output Voltage
More than 3.35 V
Less than 3.0 V
A107708
Output Voltage
More than 0.55 V
Less than 0.4 V
A103186
2
Injection Volume
+24.8%
-12.5%
A103184
Injection Volume
+24.8%
-12.5%
A103184
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
Output Voltage
Almost
no reaction
A103185
Output Voltage
More than 0.55 V
Less than 0.4 V
A103186
3
Injection Volume
+24.8%
-12.5%
A103184
Injection Volume
+24.8%
-12.5%
A103184
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
Output Voltage
More than 3.35 V
Less than 3.0 V
A107708
Output Voltage
Almost
no reaction
A103185
4
Injection volume
+24.8%
-12.5%
A103184
Injection Volume
+24.8%
-12.5%
A103184
  1. Injector
  2. Fuel pressure
  3. Gas leakage from exhaust system
    (Air-fuel ratio extremely lean or rich)
Output Voltage
Almost
no reaction
A103185
Output Voltage
Almost
no reaction
A103185
  1. The following "Control the Injection Volume" procedure enables the technicians to check and graph the output voltages of both A/F Sensor and heated oxygen sensor.
  2. To display the graph, select the following menu items on the tester: View / Line graph.

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check the conditions that would cause the engine to run with the rich air-fuel mixture.
  3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check the conditions that would cause the engine to run with the lean air-fuel mixture.


1. CHECK WIRE HARNESS (A/F SENSOR - ECM)
G038637E09
  1. Disconnect the A18 A/F sensor connector.

  1. Turn the E12 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A18-1 (HT1A) - E12-1 (HA1A)
    Below 1 Ω
    A18-3 (A1A+) - E12-21 (A1A+)
    Below 1 Ω
    A18-4 (A1A-) - E12-31 (A1A-)
    Below 1 Ω
    A18-1 (HT1A) or E12-1 (HA1A) - Body ground
    10 kΩ or higher
    A18-3 (A1A+) or E12-21 (A1A+) - Body ground
    10 kΩ or higher
    A18-4 (A1A-) or E12-31 (A1A-) - Body ground
    10 kΩ or higher

    A112065E17



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


2. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor.


NEXT


3. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear DTCs.

  1. Start the engine.

  1. Allow the engine idle for 5 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read pending DTCs.

    Result:
    Result
    Proceed to
    No DTC is output
    A
    P2237, P2238, P2239, P2252 or P2253 is output
    B



B
REPLACE ECM
A

END


← P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) (+ P2196) (from Jun 2011)P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) (from Jun 2011) →