P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012
Also covers:
- P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)
- P2241 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)
- P2242 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)
- P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)
- P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)
- P2255 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)
- P2256 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)
Versions by build date: Jun 2011 – Jul 2012 from Aug 2012
DESCRIPTION
Refer to DTC P2195 (Click here).| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2238 P2241 |
A/F sensor circuit low (bank 1 sensor 1) |
|
| Condition (a) continues for 5.0 sec. or more: (a) AF+ voltage is 0.5 V or less |
|
|
| Condition (a) continues for 5.0 sec. or more: (b) (AF+) - (AF-) = 0.1 V or less | ||
| P2239 P2242 |
A/F sensor circuit high (bank 1 sensor 1) (2 trip detection logic) |
|
| Condition (a) continues for 5.0 sec. or more: AF+ voltage is greater than 4.5 V |
|
|
| Condition (a) continues for 5.0 sec. or more: (b) (AF+) - (AF-) = greater than 0.8 V | ||
| P2252 P2255 |
Condition (a) continues for 5.0 sec. or more: AF- voltage is 0.5 V or less (2 trip detection logic) |
|
| P2253 P2256 |
Condition (a) continues for 5.0 sec. or more: AF- voltage is greater than 4.5 V |
- HINT:
- DTCs P2238, P2239, P2252 and P2253 indicate malfunctions related to bank 1 A/F sensor circuit.
- DTCs P2241, P2242, P2255 and P2256 indicate malfunctions related to bank 2 A/F sensor circuit.
- Bank 1 refers to the bank that includes the No. 1 cylinder.
- Bank 2 refers to the bank that includes the No. 2 cylinder.
- DTCs P2238, P2239, P2252 and P2253 indicate malfunctions related to bank 1 A/F sensor circuit.
MONITOR DESCRIPTION
The Air-fuel Ratio (A/F) sensor varies its output voltage in proportion to the air-fuel ratio. If the A/F sensor impedance (alternating current resistance) or output voltage deviates greatly from the standard range, the ECM determines that there is an open or short malfunction in the A/F sensor circuit.WIRING DIAGRAM
Refer to DTC P2195 (Click here).INSPECTION PROCEDURE
- HINT:
- Intelligent tester only:
- Malfunctioning areas can be found by performing the Active Test "Control the injection volume for A/F sensor" operation. The "Control the injection volume for A/F sensor" operation can determine if the A/F sensor, heated oxygen sensor or other potential trouble areas are malfunctioning or not.
- (a) Perform Active Test using the intelligent tester.
- HINT:
- "Control the injection volume for A/F sensor" is an Active Test which changes the injection volume to -12.5% or +25%.
(2) Start the engine and turn the tester ON.
(3) Warm up the engine by running the engine at 2,500 rpm for approximately 90 seconds.
(4) Enter the following menus on the intelligent tester: Powertrain / Engine and ECT / Active Test / Control the injection volume for A/F sensor.
(5) Enter the following monitor items: AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2.
(6) Perform the "Control the injection volume for A/F sensor" operation with the engine in an idling condition (press the right or left button).
- HINT:
- The "Control the injection volume for A/F sensor" operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- The "Control the injection volume for A/F sensor" operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
- Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
- Standard:
Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS B1S1 or AFS B2S1
(A/F)
+25%
Rich
Less than 3.0
AFS B1S1 or AFS B2S1
(A/F)
-12.5%
Lean
More than 3.35
O2S B1S2 or O2S B2S2
(heated oxygen sensor)
+25%
Rich
More than 0.55
O2S B1S2 or O2S B2S2
(heated oxygen sensor)
-12.5%
Lean
Less than 0.4
- NOTICE:
- The A/F sensor output has a few seconds of delay and the heated oxygen sensor output has approximately 20 seconds of delay.
| Case |
A/F Sensor (Sensor 1) Output Voltage |
Heated Oxygen Sensor (Sensor 2) Output Voltage |
Main Suspected Trouble Areas |
||
| 1 |
Injection volume +25% -12.5% |
![]() ![]() |
Injection volume +25% -12.5% |
![]() ![]() |
- |
| Output voltage More than 3.35 V Less than 3.0 V |
![]() ![]() |
Output voltage More than 0.55 V Less than 0.4 V |
![]() ![]() |
||
| 2 |
Injection volume +25% -12.5% |
![]() ![]() |
Injection volume +25% -12.5% |
![]() ![]() |
|
| Output voltage Almost no reaction |
![]() ![]() |
Output voltage More than 0.55 V Less than 0.4 V |
![]() ![]() |
||
| 3 |
Injection volume +25% -12.5% |
![]() ![]() |
Injection volume +25% -12.5% |
![]() ![]() |
|
| Output voltage More than 3.35 V Less than 3.0 V |
![]() ![]() |
Output voltage Almost no reaction |
![]() ![]() |
||
| 4 |
Injection volume +25% -12.5% |
![]() ![]() |
Injection volume +25% -12.5% |
![]() ![]() |
|
| Output voltage Almost no reaction |
![]() ![]() |
Output voltage Almost no reaction |
![]() ![]() |
||
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- These DTCs are related to the A/F sensor.
- These DTCs are recorded when A/F sensor has a malfunction, although the caption is heated oxygen sensor.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() ![]() |
Disconnect the A/F sensor connector.
Measure the resistance of the A/F sensor.
- Standard resistance (Bank 1 Sensor 1):
Tester Connection
Condition
Specified Condition
1 (HA1A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω
1 (HA1A) - 4 (A1A-)
-
10 kΩ or higher
- Standard resistance (Bank 2 Sensor 1):
Tester Connection
Condition
Specified Condition
1 (HA2A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω
1 (HA2A) - 4 (A2A-)
-
10 kΩ or higher
|
|
||||
| OK | |
| 2. INSPECT RELAY (Marking: A/F) |
![]() ![]() |
Remove the A/F sensor heater relay from the engine room relay block.
Measure the resistance of the relay.
- Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)
|
|
||||
| OK | |
| 3. CHECK WIRE HARNESS (A/F SENSOR - ECM) |
![]() ![]() ![]() ![]() |
Disconnect the A18 or A25 A/F sensor connector.
Disconnect the E6 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance (Bank 1 Sensor 1):
Tester Connection
Specified Condition
A18-1 (HA1A) - E16-2 (HA1A)
Below 1 Ω
A18-3 (A1A+) - E16-22 (A1A+)
Below 1 Ω
A18-4 (A1A-) - E16-30 (A1A-)
Below 1 Ω
A18-1 (HA1A) or E16-2 (HA1A) - Body ground
10 kΩ or higher
A18-3 (A1A+) or E16-22 (A1A+) - Body ground
10 kΩ or higher
A18-4 (A1A-) or E16-30 (A1A-) - Body ground
10 kΩ or higher
- Standard resistance (Bank 2 Sensor 1):
Tester Connection
Specified Condition
A25-1 (HA2A) - E16-1 (HA2A)
Below 1 Ω
A25-3 (A2A+) - E16-23 (A2A+)
Below 1 Ω
A25-4 (A2A-) - E16-31 (A2A-)
Below 1 Ω
A25-1 (HA2A) or E16-1 (HA2A) - Body ground
10 kΩ or higher
A25-3 (A2A+) or E16-23 (A2A+) - Body ground
10 kΩ or higher
A25-4 (A2A-) or E16-31 (A2A-) - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||









