SYSTEM DESCRIPTION
Troubleshooting · Vehicles built from Jun 2011
| ENGINE CONTROL SYSTEM |


| *1 |
ECM |
*2 |
Fuel Supply Pump Assembly |
| *3 |
Suction Control Valve |
*4 |
Fuel Temperature Sensor |
| *5 |
Common Rail Assembly |
*6 |
Fuel Pressure Sensor |
| *7 |
Pressure Discharge Valve |
*8 |
Injector Driver |
| *9 |
EDU Relay |
*10 |
Injector Assembly |
| *11 |
Diesel Throttle Body Assembly |
*12 |
Manifold Absolute Pressure Sensor |
| *13 |
Electric EGR Control Valve Assembly |
*14 |
Glow Plug Controller |
| *15 |
Glow Plug |
*16 |
Engine Coolant Temperature Sensor |
| *17 |
Intake Air Temperature Sensor (Turbo) |
*18 |
Intercooler |
| *19 |
Camshaft Position Sensor |
*20 |
Crankshaft Position Sensor |
| *21 |
Mass Air Flow Meter |
*22 |
Intake Air Temperature Sensor (Built Into Mass Air Flow Meter) |
| *23 |
Turbocharger Sub-assembly |
*24 |
DC motor, Nozzle Vane Position Sensor |
| *25 |
Differential Pressure Sensor Assembly |
*26 |
Exhaust Gas Temperature Sensor (B1S1) |
| *27 |
No. 2 Exhaust Gas Temperature Sensor (B1S2) |
*28 |
No. 3 Exhaust Gas Temperature Sensor (B1S3) |
| *29 |
Air Fuel Ratio Sensor |
*30 |
Exhaust Fuel Addition Injector Assembly |
| *31 |
VSV for EGR Bypass Valve |
*32 |
EGR Cooler |
| *33 |
VSV for Swirl Control Valve |
*34 |
Accelerator Pedal Position Sensor |
| DIESEL PARTICULATE FILTER SYSTEM DESCRIPTION |
Diesel Particulate Filter System comprehensively regulates engine control (consists of a catalytic system and a fuel injection system) that purifies particulate matter (PM) by diesel engines. The catalytic system purifies hydrocarbons (HC) and carbon monoxides (CO), and reduces PM with a catalytic converter with the Diesel Particulate Filter (DPF). The fuel injection system adds fuel into the exhaust port using the exhaust fuel addition injector to produce maintain a proper catalyst temperature for PM forced regeneration.


Text in Illustration *1
ECM
*2
Injector Driver
*3
Common Rail Assembly
*4
Fuel Pressure Sensor
*5
Pressure Discharge Valve
*6
Fuel Supply Pump Assembly
*7
VSV for EGR Bypass Valve
*8
EGR Cooler
*9
Injector Assembly
*10
Electric EGR Control Valve Assembly
*11
Diesel Throttle Body Assembly
*12
Turbocharger Sub-assembly
*13
Exhaust Fuel Addition Injector Assembly
*14
DPF Catalytic Converter
*15
Differential Pressure Sensor Assembly
*16
Exhaust Gas Temperature Sensor (B1S1)
*17
No. 2 Exhaust Gas Temperature Sensor (B1S2)
*18
No. 3 Exhaust Gas Temperature Sensor (B1S3)
*19
Air Fuel Ratio Sensor
*20
CCo Catalyst Converter
*21
Fuel Tank
-
-
DPF components:
Component
Description
DPF catalytic converter
Reduces HC, CO and PM.
Exhaust Fuel Addition Injector Assembly
Adds fuel into the exhaust port in order to raise catalyst temperature for PM forced regeneration.
Exhaust gas temperature sensor
Used for estimating the DPF catalytic converter temperature and adjusting fuel addition by ECM while PM forced regeneration is performed. Also detects the DPF catalytic converter temperature to prevent the catalytic converter temperature from rising too high.
Differential Pressure Sensor Assembly
Detects the volume of PM deposits and any incorrect vacuum hose arrangement on the DPF catalytic converter.
Air fuel ratio sensor
Used for controlling the air-fuel ratio. By controlling the air-fuel ratio, combustion control and PM forced regeneration are properly regulated.
Diagnostics Trouble Codes (DTCs) table for DPF:
- HINT:
- This table indicates typical DTC combinations for each malfunction occurrence.
*: There may be no DTC output depending on the condition of the malfunction.Trouble Area
Malfunction
DTC No.
DPF catalytic converter
Deteriorated or clogged
P062F, P2002, P200C*, P244A*, P244B*, P244C*, P2463*
Exhaust Fuel Addition Injector Assembly
Stuck open
P20CF
Stuck closed
P244A*, P244C
Low fuel addition volume
P244A*, P244B*, P244C*, P2463
Open in exhaust fuel addition injector circuit
P20CB, P244A*, P244C
Short in exhaust fuel addition injector circuit
P20CF, P20CB, P244A*, P244C
Open or short in exhaust fuel addition injector circuit
P200C*, P20CF*, P20CB, P244A*, P244C*
Exhaust gas temperature sensor
Open in exhaust gas temperature sensor circuit
P0545, P0546, P200C*, P2032, P2033, P2084, P242B, P242C, P242D, P244A*, P244C*
Short in exhaust gas temperature sensor circuit
P0545, P0546, P200C*, P2002*, P2032, P2033, P2084, P242B, P242C, P242D, P244A*, P244C*
Exhaust gas temperature sensor
P0545, P0546, P200C*, P2032, P2033, P2084, P242B, P242C, P242D, P244A*, P244C*
Differential Pressure Sensor Assembly
Open in differential pressure sensor circuit
P244A*, P244C* P2454, P2455, P2463*
Short in differential pressure sensor circuit
P244A*, P244C*, P2454, P2455, P2463*
Differential pressure sensor
P244A*, P244C*, P2454, P2455, P2463*
Differential pressure sensor clogged
P244A*, P244C*, P2453, P2463*
Incorrect vacuum hose arrangement of the differential pressure sensor
P244A*, P244C*, P2453, P2463*
Air fuel ratio sensor
Open or short in air fuel ratio sensor or heater circuit
P0031, P0032, P2238, P2239, P2252, P2253, P244B*, P2463*
Air fuel ratio sensor
P0031, P0032, P2195, P2238, P2239, P2252, P2253, P244B*, P2463*
Exhaust gas leaks
Exhaust gas leaks
P244A*, P244C*
Fuel leaks
Fuel leaks in fuel addition injector
P2002*, P200C*, P20CF*, P244A*, P244B*, P244C*, P2463*
Fuel supply pump assembly
Correct fuel pressure cannot be fed to the exhaust fuel addition injector
P244A*, P244B*, P244C*, P2463*
Diagnostics trouble code description for DPF:
DTC No.
Description
P0031
Open in air fuel ratio sensor heater control circuit (Low output)
P0032
Short in air fuel ratio sensor or heater circuit (High output)
P0545
Open or short in exhaust gas temperature sensor circuit (B1S1) (Low output)
P0546
Open or short in exhaust gas temperature sensor circuit (B1S1) (High output)
P2002
DPF catalytic converter thermal deterioration
P200C
DPF catalytic converter abnormally high exhaust gas temperature
P2032
Open or short in exhaust gas temperature sensor circuit (B1S2) (Low output)
P2033
Open or short in exhaust gas temperature sensor circuit (B1S2) (High output)
P2084
Exhaust Gas Temperature Sensor Circuit Range/Performance (B1S2)
P20CB
Open in exhaust fuel addition injector circuit
P20CF
Exhaust fuel addition injector assembly stuck open
P2195
Air fuel ratio sensor stuck lean
P2238
Open or short in air fuel ratio sensor or heater circuit (Low output)
P2239
Open or short in air fuel ratio sensor or heater circuit (High output)
P2252
Open or short in air fuel ratio sensor or heater circuit (Low output)
P2253
Open or short in air fuel ratio sensor or heater circuit (High output)
P242B
Exhaust Gas Temperature Sensor Circuit Range / Performance (B1S3)
P242C
Open or short in exhaust gas temperature sensor circuit (B1S3) (Low output)
P242D
Open or short in exhaust gas temperature sensor circuit (B1S3) (High output)
P244A
DPF catalytic converter excessive differential pressure (Low input)
P244B
DPF catalytic converter excessive differential pressure (High input)
P244C
DPF catalytic converter insufficient temperature increase
P2453
Differential pressure sensor is clogged or has incorrect vacuum hose arrangement
P2454
Open or short in differential pressure sensor circuit (Low output)
P2455
Open or short in differential pressure sensor circuit (High output)
P2463
DPF catalytic converter soot deposition
| COMMON RAIL SYSTEM DESCRIPTION |
Common rail system:
The common rail system uses high-pressure fuel for improved fuel economy. This system also provides robust engine power while suppressing engine vibration and noise.
This system stores fuel in the common rail, which has been pressurized and supplied by the fuel supply pump assembly. By storing fuel at high-pressure, the common rail system can provide fuel at stable fuel injection pressures, regardless of engine speed or engine load.
The ECM, using the injector driver, provides an electric current to the piezo actuator in each injector to regulate the fuel injection timing and volume. The ECM also monitors the internal fuel pressure of the common rail using the fuel pressure sensor. The ECM causes the fuel supply pump assembly to supply the fuel necessary to obtain the target fuel pressure.
In addition, this system uses a piezo actuator inside each injector to open and close the fuel passages. Therefore, both fuel injection time and fuel injection volume can be precisely regulated by the ECM.
The common rail system allows a two stage fuel injection process. In order to soften combustion shock, this system performs "pilot-injection" prior to the main fuel injection. This helps to reduce engine vibration and noise.

- HINT:
- If there is a problem with a fuel return pipe, as bleeding air from the fuel system may not be able to be performed properly in certain instances, such as after replacing a fuel injector, etc., the engine startability may deteriorate.
Common rail system components:
Component
Description
Common rail assembly
Stores high-pressure fuel produced by supply pump
Fuel supply pump assembly
- Operated by crankshaft via gear
- Supplies high-pressure fuel to common rail
Injector assembly
Injects fuel to combustion chamber based on signals from ECM
Fuel pressure sensor
Monitors internal fuel pressure of common rail and sends signals to ECM
Pressure discharge valve
Based on signals from ECM, opens valve when sudden deceleration occurs, or when ignition switch is off to prevent fuel pressure from becoming too high.
Suction control valve
Based on signals from ECM, adjusts fuel volume supplied to common rail and regulates internal fuel pressure
Check valve
Keeps pressure that discharges from injector
- Operated by crankshaft via gear
Diagnostic trouble code (DTC) table for the common rail system:
- HINT:
- This table indicates typical DTC combinations for each malfunction occurrence.
*: There may be no DTC output depending on the condition of the malfunction.Trouble Area
Malfunction
DTC No.
Injector assembly
Open or short in injector circuit
P0093*, P0201, P0202, P0203, P0204, P062D
Stuck open
P0093
Stuck closed
P0301, P0302, P0303, P0304
Fuel pressure sensor
Open or short in fuel pressure sensor circuit or pressure sensor output fixed
P0087, P0190, P0191, P0192, P0193
Pressure discharge valve
Open or short in pressure discharge valve circuit
P0088*, P0093*, P1229*, P1271, P1272
Stuck open
P0093
Stuck closed
P0088*, P1272
Suction control valve
Open or short in suction control valve circuit
P0627, P1229, P0088*
Stuck open
P0088*, P1229
Injector driver
Faulty injector driver
P0093*, P0201*, P0202*, P0203*, P0204*, P062D*, P1271*, P1272*
Common rail system (Fuel system)
Fuel leaks in high-pressure area
P0093
Diagnostic trouble code description for the common rail system:
DTC No.
Description
P0087
Fuel pressure sensor output does not change
P0088
Internal fuel pressure too high (220000 kPa [2243 kgf/cm2, 31900 psi] or more)
P0093
Fuel leaks in high-pressure areas
P0190
Open or short in fuel pressure sensor circuit (output voltage is too low or too high)
P0192
Open or short in fuel pressure sensor circuit (output voltage is too low)
P0193
Open or short in fuel pressure sensor circuit (output voltage is too high)
P0201
Open or short in No. 1 injector circuit
P0202
Open or short in No. 2 injector circuit
P0203
Open or short in No. 3 injector circuit
P0204
Open or short in No. 4 injector circuit
P0301
Cylinder 1 misfire detected
P0302
Cylinder 2 misfire detected
P0303
Cylinder 3 misfire detected
P0304
Cylinder 4 misfire detected
P0627
Open or short in suction control valve circuit
P062D
Open or short in injector driver or injector circuit
P1229
Fuel over-feed
P1271
Open or short in pressure discharge valve circuit
P1272
Pressure discharge valve stuck close
| INJECTION CONTROL SYSTEM DESCRIPTION |
The ECM determines the injection volume and injection timing based on signals from the accelerator pedal position sensor, crankshaft position sensor and camshaft position sensor. Based on the signals from the ECM, the injector driver controls the injectors. The injector driver also controls the suction control valve installed on the fuel supply pump assembly to help regulate fuel pressure.
The piezo type injector used in the 1KD-FTV engine makes noise when the engine is idling because this injector operates at high speed. Therefore, the injector driver controls the injector to operate at low speed when the engine is idling based on signals from the ECM to achieve noise reduction.
The feed pump is used to pump fuel from the fuel tank to the fuel supply pump assembly.


| FUEL SUPPLY PUMP OPERATION SYSTEM DESCRIPTION |


| SUCTION CONTROL VALVE OPERATION SYSTEM DESCRIPTION |
- HINT:
- The ECM controls the suction control valve operation to regulate the fuel volume that is produced by the fuel supply pump assembly for the common rail. This control is performed to regulate the internal fuel pressure of the common rail to the target injection pressure.
Small opening of the suction control valve:
When the opening of the suction control valve is small, the volume of supplied fuel is small.
The suction volume becomes small due to the narrow path despite the plunger stroke being full. The difference between the geometrical volume and suction volume creates a vacuum.
Pump output will start when the fuel pressure at (A) becomes higher than the common rail pressure (B).


Large opening of the suction control valve:
When the opening of the suction control valve is large, the volume of supplied fuel is large.
If the plunger stroke is full, the suction volume becomes large because of the wide path.
Pump output will start when the fuel pressure at (A) becomes higher than the common rail pressure (B).

