2014 Hilux · Service Manual ENGINE

P0095 Intake Air Temperature Sensor 2 Circuit

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The diesel turbo Intake Air Temperature (IAT) sensor is built into the charge air cooler and senses the IAT. A built-in thermistor of the sensor changes the resistance value according to the intake air temperature. The lower the IAT is, the greater the thermistor resistance value becomes, and the higher the temperature is, the lower the resistance value becomes (see Fig. 1).
The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve the driveability with a cold engine.
G036559E03
DTC No.
DTC Detection Condition
Trouble Area
P0095
Open or short in diesel turbo IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in diesel turbo IAT sensor circuit
  2. Diesel turbo IAT sensor
  3. ECM
P0097
Short in diesel turbo IAT sensor circuit for 0.5 seconds
(sensor resistance value less than 25 Ω [sensor output voltage less than 0.05 V])
(1 trip detection logic)
  1. Open or short in diesel turbo IAT sensor circuit
  2. Diesel turbo IAT sensor
  3. ECM
P0098
Open in diesel turbo IAT sensor circuit for 0.5 seconds
(sensor resistance value more than 156 kΩ [sensor output voltage more than 4.9 V])
(1 trip detection logic)
  1. Open or short in diesel turbo IAT sensor circuit
  2. Diesel turbo IAT sensor
  3. ECM

HINT:
When DTC P0095, P0097, and/or P0098 is set, check the intake air temperature by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / Intake Air Temp (Turbo).


Reference:
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or more
Short circuit


WIRING DIAGRAM

A119971E07

INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If different DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMP [TURBO])
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).

  1. Read the value.

    OK:
    Same value as the actual intake air temperature.


    Result:
    Temperature Displayed
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or more
    B
    OK (same as air temperature near to intake manifold)
    C



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS
A


2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

  1. A099828E09
    Disconnect the I4 diesel turbo IAT sensor connector.

  1. Connect terminals 1 and 2 of the diesel turbo IAT sensor wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).

  1. Read the value.

    Standard:
    140°C (284°F) or more.



OK
CONFIRM GOOD CONNECTION AT SENSOR. IF OK, REPLACE DIESEL TURBO INTAKE AIR TEMPERATURE
NG


3. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)

  1. A099829E08
    Disconnect the I4 diesel turbo IAT sensor connector.

  1. Connect terminals THIA and E2 of the E8 ECM connector.

    HINT:
    Before checking, perform a visual and contact pressure check on the ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).

  1. Read the value.

    Standard:
    140°C (284°F) or more.



OK
REPAIR OR REPLACE HARNESS OR CONNECTOR
NG

CONFIRM GOOD CONNECTION AT ECM. IF OK, REPLACE ECM

4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A083863E44
    Disconnect the I4 diesel turbo IAT sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).

  1. Read the value.

    Standard:
    -40°C (-40°F) or more.



OK
CONFIRM GOOD CONNECTION AT SENSOR. IF OK, REPLACE DIESEL TURBO INTAKE AIR TEMPERATURE
NG


5. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN ECM)

  1. A099830E10
    Disconnect the I4 diesel turbo IAT sensor connector.

  1. Disconnect the E8 ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).

  1. Read the value.

    Standard:
    -40°C (-40°F) or more.



OK
REPAIR OR REPLACE HARNESS OR CONNECTOR
NG

REPLACE ECM


← P0093 Fuel System Leak Detected - Large Leak (from Aug 2014)P0095 Intake Air Temperature Sensor 2 Circuit (+ P0097, P0098) (Aug 2012 – Jul 2013) →