REMOVAL
Removal / installation · Vehicles built from Jun 2011
| 1. DISCHARGE FUEL SYSTEM PRESSURE |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
| 3. REMOVE FUEL TANK CAP |
| 4. REMOVE NO. 3 FUEL TUBE CLAMP |
Remove the tube clamp from the fuel tube.

| 5. DISCONNECT FUEL MAIN TUBE AND FUEL RETURN TUBE |
Pinch and pull the main tube connector to disconnect the connector from the pipe. Then pinch and pull the return tube connector to disconnect the connector from the pipe.

- NOTICE:
- Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
- Do not use any tools to separate the pipe and connector.
- Do not forcefully bend or twist the nylon tube.
- Check for foreign matter on the pipe seal surface. Clean if necessary.
- Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
- If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
- Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
Unleaded specification vehicle:
Disconnect the vent line hose.
| 6. DISCONNECT FUEL TANK TO FILLER PIPE HOSE |
Disconnect the filler pipe hose from the fuel tank filler pipe.

| 7. DISCONNECT FUEL TANK BREATHER HOSE |
Disconnect the breather hose from the fuel tank filler pipe.
| 8. REMOVE FUEL TANK FILLER PIPE |
Remove the bolt and filler pipe.
| 9. REMOVE FUEL TANK |
Set a mission jack underneath the fuel tank.

Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.
Slightly lower the mission jack.
- NOTICE:
- Be careful not to cut the wirings.
Remove the clip. Then fold back approximately half of each cushion rubber so that the wire harness can be removed in the step below.

Disconnect the fuel pump connector and detach the 6 wire harness clips from the fuel tank.

- NOTICE:
- Before this procedure, check the connector for dirt, mud or other contamination.
- Do not use any tools in this procedure.
- Before this procedure, check the connector for dirt, mud or other contamination.
| 10. REMOVE NO. 1 FUEL TANK CUSHION |
Using needle-nose pliers, remove the 4 clips and nut as shown in the illustration and then remove the heat insulator.

Remove the clip and 2 fuel tank cushions from the fuel tank.

| 11. REMOVE FUEL PUMP GAUGE RETAINER |
Remove the 2 tube joint clips and pull out the 2 fuel tank tubes.

- NOTICE:
- Remove any dirt and foreign matter on the fuel tube joint before performing this work.
- Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
- Perform this work by hand. Do not use any tools.
- Do not forcibly bend, twist or turn the nylon tube.
- Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.
- Remove any dirt and foreign matter on the fuel tube joint before performing this work.
Remove the fuel tank return tube and fuel tank main tube from the fuel tank.
Temporarily install SST (plate and 4 claws) to the fuel pump gauge retainer.

- SST
- 09808-14030
- HINT:
- Be sure to use 4 SST (claws) as shown in the illustration.
- Engage SST (claws) securely with the fuel pump gauge retainer ribs to secure SST.
- Be sure to use 4 SST (claws) as shown in the illustration.
While pressing SST (claws) against the fuel pump gauge retainer ribs securely, install the 4 bolts.
- HINT:
- Install SST while pressing SST (claws) against the fuel pump gauge retainer (towards the center of SST).
Install SST (handle).
Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing SST, rotate the handle slowly to loosen the fuel pump gauge retainer.

- SST
- 09808-14030
- NOTICE:
- When the retainer is loosened, be careful as the fuel pump will spring upward from the force of the spring.
- Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.
- Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
- Make sure to rotate SST (handle) horizontally. If SST (handle) is rotated at an angle, SST may come off.
- Do not spin SST too fast or use an impact wrench as this may result in damage to components.
- If SST comes off of the fuel pump gauge retainer, loosen SST (bolts) and reinstall SST.
- When the retainer is loosened, be careful as the fuel pump will spring upward from the force of the spring.
- HINT:
- The tips of SST (claws) can be fitted onto the ribs of the fuel pump gauge retainer.
Remove the fuel pump gauge retainer.
| 12. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
Remove the fuel gauge tube from the fuel tank.
- NOTICE:
- Be careful not to bend the arm of the fuel sender gauge.
Remove the gasket from the fuel tank.
