2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jun 2011


1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. Even after discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. A118150E01
    Disconnect the fuel pump connector.

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch OFF.

    HINT:
    DTC P0171/25 (system too lean) may be set.

  1. Crank the engine again, then check that the engine does not start.

  1. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

  1. Connect the fuel pump connector.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


3. REMOVE FUEL TANK CAP

4. REMOVE NO. 3 FUEL TUBE CLAMP

  1. G038853E01
    Remove the tube clamp from the fuel tube.


5. DISCONNECT FUEL MAIN TUBE AND FUEL RETURN TUBE

  1. A111068E01
    Pinch and pull the main tube connector to disconnect the connector from the pipe. Then pinch and pull the return tube connector to disconnect the connector from the pipe.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.

  1. Disconnect the vent line hose.


6. DISCONNECT FUEL TANK TO FILLER PIPE HOSE
  1. Disconnect the filler pipe hose from the fuel tank filler pipe.


7. DISCONNECT FUEL TANK BREATHER HOSE
  1. Disconnect the breather hose from the fuel tank filler pipe.


8. REMOVE FUEL TANK FILLER PIPE
  1. Remove the bolt and filler pipe.


9. REMOVE FUEL TANK
  1. Set a mission jack underneath the fuel tank.

  1. A118151
    Remove the 3 bolts, 3 clips, 3 pins and 3 fuel tank bands.

  1. Slightly lower the mission jack.

    NOTICE:
    Be careful not to cut the wirings.

  1. A118152E01
    Fold back approximately half of each cushion rubber so that the wire harness can be removed in the next step.

  1. A118153
    Disengage the 4 wire harness clips from the fuel tank as shown in the illustration.

  1. Disconnect the fuel pump connector.

    NOTICE:
    1. Before this procedure, check the connector for dirt, mud or other contamination.
    2. Do not use any tools in this procedure.


10. REMOVE NO. 1 FUEL TANK CUSHION

  1. A116052
    Using needle-nose pliers, remove the 5 clips shown in the illustration and then remove the heat insulator.

  1. A118155
    Remove the 3 fuel tank cushions from the fuel tank.


11. REMOVE FUEL PUMP GAUGE RETAINER

  1. A252104E02
    Remove the 2 tube joint clips and pull out the 2 fuel tank tubes.

    NOTICE:
    1. Remove any dirt and foreign matter on the fuel tube joint before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.

  1. Remove the fuel tank return tube and fuel tank main tube from the fuel tank.

  1. A246112E05
    Temporarily install SST (plate and 4 claws) to the fuel pump gauge retainer.
    SST
    09808-14030  

    HINT:
    1. Be sure to use 4 SST (claws) as shown in the illustration.
    2. Engage SST (claws) securely with the fuel pump gauge retainer ribs to secure SST.

  1. While pressing SST (claws) against the fuel pump gauge retainer ribs securely, install the 4 bolts.

    HINT:
    Install SST while pressing SST (claws) against the fuel pump gauge retainer (towards the center of SST).

  1. Install SST (handle).

  1. A241650E03
    Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing SST, rotate the handle slowly to loosen the fuel pump gauge retainer.
    SST
    09808-14030  

    NOTICE:
    1. When the retainer is loosened, be careful as the fuel pump will spring upward from the force of the spring.
    2. Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.
    3. Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
    4. Make sure to rotate SST (handle) horizontally. If SST (handle) is rotated at an angle, SST may come off.
    5. Do not spin SST too fast or use an impact wrench as this may result in damage to components.
    6. If SST comes off of the fuel pump gauge retainer, loosen SST (bolts) and reinstall SST.

    HINT:
    The tips of SST (claws) can be fitted onto the ribs of the fuel pump gauge retainer.

  1. Remove the fuel pump gauge retainer.


12. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
  1. Remove the fuel gauge tube from the fuel tank.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Remove the gasket from the fuel tank.

← COMPONENTS (from Jun 2011)INSTALLATION (Jun 2011 – Jul 2012) →