2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. DISCONNECT BATTERY NEGATIVE TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. DRAIN ENGINE COOLANT
  1. Remove the radiator cap.

  1. Loosen the cylinder block drain cock plug and radiator drain plug, and then the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


    A270641E01


3. REMOVE V-BANK COVER

  1. A112983
    Remove the 2 nuts and the V-bank cover.


4. DISCONNECT NO. 2 VENTILATION HOSE

A075594

5. REMOVE AIR CLEANER

  1. A075595
    Disconnect the vacuum hose.

  1. Disconnect the MAF meter connector.

  1. Remove the 2 wire harness clamps.

  1. A075596
    Loosen the 2 hose clamps.

  1. Remove the 2 bolts and air cleaner.


6. REMOVE INTAKE AIR SURGE TANK

A076500E02
  1. Disconnect the 2 water by-pass hoses.

  1. A075644E01
    Disconnect the purge line hose.

  1. A075645E01
    Disconnect the ventilation hose.

  1. A075646E01
    Disconnect the 2 VSV connectors.

  1. Disconnect the throttle body with motor connector.

  1. Separate the 3 wire harness clamps and hose clamp.

  1. A076501E01
    Remove the 2 bolts and throttle body bracket.

  1. A076502E01
    Remove the bolt and oil baffle plate.

  1. Remove the 4 bolts and 2 surge tank stays.

  1. A075648E01
    Remove the 2 nuts.

  1. Using an 8 mm hexagon socket wrench, remove the 4 bolts, intake air surge tank and gasket.


7. REMOVE IGNITION COIL

8. REMOVE CYLINDER HEAD COVER RH

  1. A072943E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, head cover and gasket.


9. REMOVE CYLINDER HEAD COVER LH

  1. A072944E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.

  1. Remove the ventilation valve from the cylinder head cover.


10. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A076530E01
    Turn the crankshaft pulley, and align its groove with the timing mark 0 of the timing chain cover.

  1. G038065E01
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.


11. REMOVE NO. 1 CHAIN TENSIONER

A072958E01

NOTICE:
  1. Never rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC before rotating it.

  1. While rotating the stopper plate of the tensioner upward, push in the plunger of the chain tensioner as shown in the illustration.

  1. While rotating the stopper plate of the tensioner downward, insert a bar of diameter of 3.5 mm (0.138 in.) into the holes in the stopper plate and tensioner to fix the stopper plate.

  1. Remove the 2 bolts and chain tensioner.


12. REMOVE NO. 4 CAMSHAFT

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. G038075E01
    While pushing down the No. 3 chain tensioner, insert a diameter of 1.0 mm (0.039 in.) into the hole to fix it in place.

  1. G038076E01
    Hold the hexagonal portion of the No. 4 camshaft with a wrench, and remove the camshaft timing gear set bolt.

    NOTICE:
    Be careful not to damage the cylinder head and valve lifter with the wrench.

  1. Separate the camshaft timing gear from the No. 4 camshaft.

  1. A076482E01
    Uniformly loosen and remove the 8 bearing cap bolts in several passes in the sequence shown in the illustration.

  1. Remove the 4 bearing caps and No. 4 camshaft.


13. REMOVE NO. 3 CHAIN TENSIONER

  1. G038077E01
    Remove the No. 3 chain tensioner bolt, and then remove the No. 3 chain tensioner and camshaft timing gear.


14. REMOVE NO. 3 CAMSHAFT

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. A076484E01
    Release the chain tension between the camshaft timing gear (LH bank) and crankshaft timing gear by turning the crankshaft pulley counterclockwise slightly.

  1. G038400E01
    Hold the hexagonal portion of the No. 3 camshaft with a wrench, and loosen the camshaft timing gear set bolt.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear assembly.

  1. G038401E01
    Slide the camshaft timing gear and separate the No. 1 chain from the camshaft timing gear.

  1. A076487E02
    Uniformly loosen and remove the 8 bearing cap bolts in several passes in the sequence shown in the illustration.

  1. Remove the 4 bearing caps.

  1. G038402E01
    Remove the camshaft timing gear set bolt with the No. 3 camshaft is lifted up, and then remove the No. 3 camshaft and camshaft timing gear with No. 2 chain.

  1. A076489E01
    Tie the No.1 chain with a string as shown in the illustration.

    NOTICE:
    Be careful not to drop anything inside the timing chain cover.

← REMOVAL (Aug 2012 – Jul 2013)INSPECTION (from Jun 2011) →