2014 Hilux · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012

HINT:
  1. Thoroughly clean all parts to be assembled.
  2. Before installing the parts, apply new engine oil to all sliding and rotating surfaces.
  3. Replace all gaskets, O-rings and oil seals with new parts.


1. REMOVE NO. 1 ENGINE HANGER

  1. A072941E01
    Remove the 2 bolts and No. 1 engine hanger.


2. REMOVE NO. 2 ENGINE HANGER
  1. Remove the 2 bolts and No. 2 engine hanger.


3. REMOVE OIL DIPSTICK GUIDE
  1. Remove the bolt and pull out the oil dipstick.

  1. Remove the O-ring from the oil level gauge guide.


4. REMOVE CYLINDER BLOCK WATER DRAIN COCK
  1. Remove the cylinder block water drain cock.


5. REMOVE VVT SENSOR
  1. Remove the 2 bolts and 2 sensors.


6. REMOVE CRANKSHAFT POSITION SENSOR
  1. Remove the bolt and crankshaft position sensor.


7. REMOVE OIL CONTROL VALVE FILTER

  1. A072942E01
    Remove the plug, filter and gasket from each cylinder head.


8. REMOVE CYLINDER HEAD COVER RH

  1. A072943E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, head cover and gasket.


9. REMOVE CYLINDER HEAD COVER LH

  1. A072944E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.

  1. Remove the ventilation valve from the cylinder head cover.


10. REMOVE CRANKSHAFT PULLEY

  1. A072945E01
    Turn the crankshaft pulley, and align its groove with the timing mark 0 of the timing chain cover.

  1. G038065E03
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°) and align the timing marks as above.

  1. A072947E01
    Using SST, hold the crankshaft pulley and loosen the pulley set bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A072948E01
    Using the pulley set bolt and SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05030)


11. REMOVE OIL PAN DRAIN PLUG
  1. Remove the drain plug and gasket.


12. REMOVE NO. 2 OIL PAN

  1. A112956E01
    Remove the 14 bolts and 2 nuts.

  1. A112957
    Insert the blade of an oil pan seal cutter between the oil pan and No. 2 oil pan, cut through the applied sealer and remove the No. 2 oil pan.

    NOTICE:
    1. Be careful not to damage the contact surface of the No. 2 oil pan and oil pan.
    2. Be careful not to damage the No. 2 oil pan flange.


13. REMOVE OIL STRAINER

  1. A112955
    Remove the 2 nuts, oil strainer and gasket.


14. REMOVE NO. 1 OIL PAN

  1. A112952E02
    Remove 17 bolts and 2 nuts.

  1. A112954
    Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block in the sequence shown.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

  1. Remove the O-ring from the timing chain cover.


15. REMOVE WATER PUMP

  1. A072954E02
    Remove the 17 bolts, water pump and gasket.


16. REMOVE TIMING CHAIN COVER

  1. G036855E01
    Remove the 15 bolts and 2 nuts.

  1. G036859E01
    Remove the timing chain cover by prying the portions between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

  1. Remove the O-ring from the LH cylinder head.


17. REMOVE NO. 1 CHAIN TENSIONER

A072958E01

NOTICE:
  1. Never rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC before rotating it.

  1. While rotating the stopper plate of the tensioner upward, push in the plunger of the chain tensioner as shown in the illustration.

  1. While rotating the stopper plate of the tensioner downward, insert a bar of diameter of 3.5 mm (0.138 in.) into the holes in the stopper plate and tensioner to fix the stopper plate.

  1. Remove the 2 bolts and chain tensioner.


18. REMOVE CHAIN TENSIONER SLIPPER

19. REMOVE NO. 1 IDLE GEAR

  1. G036860E01
    Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.


20. REMOVE NO. 2 VIBRATION DAMPER

  1. G036844E01
    Remove the 2 chain vibration dampers.


21. REMOVE CHAIN

22. REMOVE CRANKSHAFT TIMING SPROCKET

23. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. G036808E01
    Remove the 2 bolts and No. 1 chain vibration damper.


24. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (RH BANK)

  1. G036850E01
    While raising up the No. 2 chain tensioner, insert a pin of diameter of 1.0 mm (0.039 in.) into the hole to fix it.

  1. G036834E01
    Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts, camshaft timing gear, camshaft timing gear assembly and No. 2 timing chain.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear assembly.


25. REMOVE NO. 2 CHAIN TENSIONER

  1. A072962E01
    Remove the bolt and No. 2 chain tensioner.


26. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (LH BANK)

  1. G036835E01
    While pushing down the No. 3 chain tensioner, insert a pin of diameter of 1.0 mm (0.039 in.) into the hole to fix it.

  1. G036836E01
    Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts, camshaft timing gear, camshaft timing gear assembly and No. 2 timing chain.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear assembly.


27. REMOVE NO. 3 CHAIN TENSIONER

  1. A072965E01
    Remove the bolt and No. 3 chain tensioner.


28. REMOVE CAMSHAFT

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which received the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. A072966E01
    Remove the camshafts of the RH bank.

    1. Rotate the camshafts counterclockwise using hexagonal portion of the each camshaft so that the cam lobes of the No. 1 cylinder may face as shown in the illustration.

    2. A072967E03
      Uniformly loosen and remove the 16 bearing cap bolts in several passes, in the sequence shown.

    3. Remove the 8 bearing caps and 2 camshafts.

  1. A072968E03
    Remove the camshafts of the LH bank.

    1. Uniformly loosen and remove the 16 bearing cap bolts in several passes, in the sequence shown.

    2. Remove the 8 bearing caps and 2 camshafts.


29. REMOVE NO. 1 CAMSHAFT BEARING

30. REMOVE NO. 2 CAMSHAFT BEARING

31. REMOVE CYLINDER HEAD

  1. A072969E01
    Remove the 2 cylinder head bolts on the LH cylinder head in several passes, in the sequence shown.

  1. A072970E02
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts on each cylinder head, in several passes, in the sequence shown, then repeat for the other side as shown. Remove the 16 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop the plate washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in incorrect order.

  1. A072971E01
    Lift the cylinder head from the dowels on the cylinder block, and place the 2 cylinder heads on wooden blocks on a bench.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.

    HINT:
    If the cylinder head is difficult to lift off, pry between the cylinder head and cylinder block with a screwdriver.

  1. Remove the RH and LH cylinder head gaskets.


32. REMOVE NO. 1 WATER OUTLET PIPE

  1. A076246E01
    Separate the knock sensor wire.

  1. Remove the bolt, 2 nuts and water outlet pipe.


33. REMOVE KNOCK SENSOR

  1. A076270E01
    Disconnect the knock sensor connectors.

  1. Remove the 2 bolts and 2 knock sensors.


34. REMOVE ENGINE REAR OIL SEAL RETAINER

  1. A076247E01
    Remove the 5 bolts and 2 nuts.

  1. Using a screwdriver, remove the oil seal retainer by prying the portions between the oil seal retainer and crankshaft bearing cap.


35. REMOVE VALVE LIFTER

A075601E01

HINT:
Arrange the valve lifter in the correct order.


36. REMOVE VALVE

A075602E01

HINT:
Arrange the valves, inner compression springs, valve spring retainers and valve spring retainer rocks in the correct order.

  1. Place the cylinder head on the wooden block.

  1. Using SST, compress the inner compression spring and remove the 2 valve spring retainer locks.

    SST
    09202-70020   (09202-00010)

  1. Remove the valve, inner compression spring and valve spring and valve spring retainer.


37. REMOVE VALVE SPRING SEAT

  1. A075603E01
    Using compressed air and a magnet hand, remove the valve spring seat by blowing air.


38. REMOVE VALVE STEM OIL SEAL

  1. A075604E01
    Using a needle-nose pliers, remove the valve stem oil seal.


39. CLEAN CYLINDER HEAD

  1. A075605E01
    Using a gasket scraper, remove all the gasket material from the cylinder block contact surface.

    NOTICE:
    Be careful not to scratch the cylinder block contact surface.

  1. A075606E01
    Using a wire brush, remove all the carbon from the combustion chambers.

    NOTICE:
    Be careful not to scratch the combustion chambers.

  1. A075607E01
    Using a valve guide bushing brush and solvent, clean all the valve guide bushes.

  1. A075608E01
    Using a soft brush and solvent, thoroughly clean the cylinder head.


40. CLEAN VALVE

  1. EM00580E01
    Using a gasket scraper, chip off any carbon from the valve head.

  1. Using a wire brush, thoroughly clean the valve.


41. REMOVE CONNECTING ROD CAP
  1. Using SST, remove the 2 connecting rod cap bols.

    SST
    09011-38121  

  1. Remove the connecting rod cap.


42. REMOVE PISTON WITH CONNECTING ROD

  1. A076043E01
    Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearings, connecting rod and cap together.
    2. Arrange the piston and connecting rod assemblies in the correct order.


43. REMOVE PISTON RING SET

  1. A076044E01
    Using a piston ring expander, remove the 2 compression rings.

  1. Remove the 2 side rails and oil ring by hand.


44. REMOVE PISTON PIN HOLE SNAP RING

  1. P012403E01
    Using a small screwdriver, pry out the 2 snap rings.


45. REMOVE PISTON WITH PIN

  1. A076045E05
    Gradually heat the piston to approximately 80°C (176°F).

  1. A076046E01
    Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.

    HINT:
    1. The piston and pin are a matched set.
    2. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.


46. REMOVE CRANKSHAFT

  1. A076048E02
    Uniformly loosen and remove the 8 main bearing cap bolts and seal washers in the several passes, in the sequence shown.

  1. A076049E02
    Uniformly loosen and remove the 16 main bearing cap bolts in several passes, in the sequence shown.

  1. A076050E01
    A076068E01
    Using a screwdriver, pry out main bearing caps. Remove the 4 main bearing caps and lower bearings.

    NOTICE:
    1. Pull up the main bearing cap little by little to the right and the left by turns.
    2. Be careful not to damage the joint surface of the cylinder block and the main bearing cap.


47. REMOVE CRANKSHAFT THRUST WASHER SET

48. REMOVE CRANKSHAFT BEARING

49. REMOVE OIL NOZZLE

  1. A076051E01
    Using a 5 mm socket hexagon wrench, remove the 3 oil nozzles.


50. REMOVE TAPER SCREW PLUG

NOTICE:
It is not necessary to remove a taper screw plug unless it is being replaced.

← DISASSEMBLY (Jun 2011 – Jul 2012)INSPECTION (Jun 2011 – Jul 2014) →