2014 Hilux · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Jun 2011 – Jul 2014 from Aug 2014


1. REMOVE OIL FILLER CAP

2. REMOVE VENTILATION VALVE

  1. A099685E01
    Loosen the hose clamp and disconnect the ventilation hose from the valve.

  1. Remove the valve.


3. REMOVE CYLINDER HEAD COVER

  1. G035202E05
    Remove the 19 bolts, 2 nuts, cover and 2 gaskets.


4. REMOVE CRANKSHAFT PULLEY

A097861E04
  1. Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear and sprocket are aligned with the timing marks of the No. 1 bearing cap, as shown in the illustration.

  1. A099211E01
    Using SST, hold the crankshaft pulley and remove the pulley set bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. G035121E01
    Using the set bolt and SST, remove the pulley bolt and pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)


5. REMOVE NO. 2 OIL PAN

A099215E10
  1. Remove the drain plug and gasket.

  1. Remove the 20 bolts and 2 nuts.

  1. Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.


6. REMOVE OIL STRAINER

  1. A334454
    Remove the 2 bolts, nut, oil strainer and gasket.


7. REMOVE NO. 1 OIL PAN

G036411E02
  1. Remove the 16 bolts and 2 nuts.

  1. Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.


8. REMOVE TIMING CHAIN COVER

G036504E01
  1. Remove the 19 bolts and 2 nuts shown in the illustration.

  1. A097897E02
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.

  1. Remove the 3 O-rings.

  1. G036021E02
    Using a 10 mm socket hexagon wrench, remove the timing gear case plug.


9. REMOVE WATER PUMP

  1. A087223E03
    Remove the 8 bolts, water pump and gasket.


10. REMOVE TIMING CHAIN COVER OIL SEAL

  1. A097898E01
    Place the timing chain cover on wooden blocks.

  1. Using a screwdriver with its tip taped, pry out the oil seal.

  1. A172563E01
    Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.
    SST
    09223-75010  
    09950-70010   (09951-07150)

    HINT:
    When installing the crankshaft pulley, check the shape of the pulley. The correct pulley has a groove (Click here).

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap the oil seal at an angle.

  1. Apply a light coat of MP grease to a new oil seal lip.


11. REMOVE OIL PUMP RELIEF VALVE

  1. A086864E01
    Using a 27 mm socket wrench, remove the plug and gasket.

  1. Remove the valve spring and relief valve.


12. REMOVE TIMING CHAIN GUIDE
  1. Remove the 2 bolts, timing chain guide and O-ring.


13. REMOVE TIMING CHAIN TENSIONER

A097899E02

NOTICE:
  1. When the chain tensioner is removed, do not rotate the crankshaft.
  2. When the chain is removed and the camshaft needs to be rotated, rotate the crankshaft 90° to the right.

  1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate downward to set the lock, and insert a 1.27 mm hexagon wrench into the stopper plate's hole.

  1. Remove the bolt, nut, chain tensioner and gasket.


14. REMOVE CHAIN TENSIONER SLIPPER
  1. Remove the bolt and tensioner slipper.


15. REMOVE VIBRATION DAMPER
  1. Remove the 2 bolts and vibration damper.


16. REMOVE TIMING CHAIN

17. REMOVE CRANKSHAFT TIMING SPROCKET

18. REMOVE CRANKSHAFT POSITION SENSOR PLATE

19. REMOVE CRANKSHAFT PULLEY SET KEY
  1. Remove the 2 pulley set keys from the crankshaft.


20. REMOVE OIL JET
  1. Remove the bolt, oil jet and gasket.


21. REMOVE CAMSHAFT

  1. A097866E01
    Uniformly loosen the 21 bearing cap bolts in several passes in the order shown in the illustration. Then remove the oil delivery pipe, O-ring and 9 bearing caps.

  1. Remove the 9 bearing caps, oil delivery pipe, O-ring and 2 camshafts.

    NOTICE:
    1. Place the camshaft on a flat surface, maintain this position and loosen the bolts uniformly.
    2. Do not pry the camshaft with a tool by applying excessive force to it.
    3. Do not damage the reception part of the exhaust on the cylinder head side.


22. REMOVE CAMSHAFT TIMING SPROCKET

  1. A086867E01
    Fix the camshaft with a vise, and then remove the sprocket bolt and camshaft timing sprocket.

    NOTICE:
    Be careful not to damage the camshaft.


23. REMOVE CAMSHAFT TIMING GEAR

  1. A097871E01
    Remove the flange bolt of the camshaft timing gear.

    NOTICE:
    1. Be sure not to remove the other 3 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.


24. REMOVE CYLINDER HEAD

  1. A097901E01
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.

  1. Remove the cylinder head and gasket.


25. REMOVE OIL FILTER

  1. A097902E01
    Using SST, remove the oil filter.
    SST
    09228-07501  


26. REMOVE OIL FILTER UNION
  1. Using a 27 mm socket wrench, remove the oil filter union.


27. REMOVE OIL FILTER BRACKET
  1. Remove the oil filter bracket union bolt, gasket and oil filter union.

  1. Remove the oil filter bracket and O-ring.

  1. Remove the O-ring from the oil filter bracket union bolt.


28. REMOVE ENGINE REAR OIL SEAL RETAINER

  1. A097903E01
    Remove the 6 bolts.

  1. Using a screwdriver with its tip taped, pry out the oil seal retainer.


29. REMOVE VALVE ROCKER ARM

HINT:
Each rocker arm must be reinstalled to its original location.


30. REMOVE VALVE STEM CAP

HINT:
Each valve stem cap must be reinstalled to its original location.


31. REMOVE VALVE LASH ADJUSTER

HINT:
Each lash adjuster must be reinstalled to its original location.


32. REMOVE INTAKE VALVE

  1. A333831E01
    Using SST and wooden blocks, compress the compression spring and remove the valve retainer locks.
    SST
    09202-70020  
    09202-00020  

  1. Remove the retainer, compression spring, valve, valve spring and spring seat.

    HINT:
    Each intake valve must be reinstalled to its original location.


33. REMOVE EXHAUST VALVE

  1. A333832E01
    Using SST and wooden blocks, compress the compression spring and remove the valve retainer locks.
    SST
    09202-70020  
    09202-00020  

  1. Remove the retainer, compression spring, valve, valve spring and spring seat.

    HINT:
    Each exhaust valve must be reinstalled to its original location.


34. REMOVE VALVE STEM OIL SEAL
  1. Using needle-nose pliers, remove the oil seal.


35. REMOVE OIL CONTROL VALVE FILTER
  1. Using an 8 mm hexagon wrench, remove the screw plug.

  1. Remove the oil control valve filter and gasket.


36. REMOVE NO. 1 HEAD STRAIGHT SCREW PLUG

  1. A097933E01
    Using a 10 mm hexagon wrench, remove the 3 screw plugs.


37. REMOVE NO. 2 HEAD STRAIGHT SCREW PLUG

  1. A097934E01
    Using a 9 mm hexagon wrench, remove the screw plug.


38. INSPECT CONNECTING ROD THRUST CLEARANCE

  1. A087181E01
    Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.15 to 0.35 mm (0.006 to 0.014 in.)

    Maximum thrust clearance:
    0.40 mm (0.016 in.)

    If the thrust clearance is greater than the maximum, replace the connecting rod assembly(s). If necessary, replace the crankshaft.


39. INSPECT CONNECTING ROD OIL CLEARANCE
  1. Check that the matchmarks on the connecting rod and cap are aligned to ensure the correct reassembly.

    HINT:
    The matchmarks on the connecting rods and caps are for ensuring the correct reassembly.

  1. G036554E01
    Remove the 2 connecting rod cap bolts.

  1. Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

    HINT:
    Keep the lower bearing inserted to the connecting rod cap.

  1. Clean the crank pin and bearing.

  1. Check the crank pin and bearing for pitting and scratches.

  1. A097948E01
    Lay a strip of Plastigage on the crank pin.

  1. A097980E01
    Install the connecting rod cap.

    NOTICE:
    Do not turn the crankshaft.


    1. Match the numbered connecting rod cap with the connecting rod.

    2. Align the pins of the connecting rod cap with the pin holes of the connecting rod, and install the connecting rod cap.

    3. Check that the front mark of the connecting rod cap is facing forward.

  1. G035198E01
    Install the connecting rod cap bolts.

    HINT:
    1. The connecting rod cap bolts are tightened in 2 progressive steps.
    2. If any connecting rod bolt is broken or deformed, replace it.


    1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.

    2. Install and alternately tighten the bolts of the connecting rod cap in several passes.

      Torque:
      24.5 N*m{ 250 kgf*cm , 18 ft.*lbf }

      If any one of the connecting rod cap bolts does not meet the torque specification, replace the cap bolts.

    3. A099641E01
      Mark the front of the connecting rod cap bolts with paint.

    4. Retighten the connecting rod cap bolts 90°as shown.

    5. Check that the painted mark is now at a 90°angle to the front.

  1. Remove the 2 bolts and connecting rod cap.

  1. A087186E01
    A097950E01
    Measure the Plastigage at its widest point.

    Standard oil clearance:
    0.039 to 0.066 mm (0.0015 to 0.0026 in.)

    If the crank pin or bearing is damaged, replace the bearings. If necessary, replace the crankshaft.

    HINT:
    If replacing a bearing, replace it with one that has the same number as its respective connecting rod cap. Each bearing's standard thickness is indicated by a 4, 5 or 6 mark on its surface.

    Standard bearing center wall thickness:
    Mark
    Specified Condition
    4
    1.484 to 1.487 mm (0.0584 to 0.0585 in.)
    5
    1.488 to 1.490 mm (0.0586 to 0.0587 in.)
    6
    1.491 to 1.493 mm (0.0587 to 0.0588 in.)

  1. Completely remove the Plastigage.


40. REMOVE PISTON WITH CONNECTING ROD

  1. G035191E03
    Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearing, connecting rod and cap together.
    2. Arrange the piston and connecting rod assemblies in the correct order.


41. INSPECT CRANKSHAFT THRUST CLEARANCE

  1. A087188E01
    Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.020 to 0.220 mm (0.0008 to 0.0087 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is greater than the maximum, replace the thrust washers as a set.

    Thrust washer thickness:
    2.440 to 2.490 mm (0.0961 to 0.0980 in.)


42. INSPECT CRANKSHAFT OIL CLEARANCE

  1. A097951E03
    Uniformly loosen the 10 bearing cap bolts in several passes in the sequence shown in the illustration.

    HINT:
    1. Keep the lower bearings and crankshaft bearing caps together.
    2. Arrange the thrust washers in the correct order.

  1. Clean each main journal and bearing.

  1. Check each main journal and bearing for pitting and scratches.
    If the journal or bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.

  1. Place the crankshaft on the cylinder block.

  1. A097962E01
    Lay a strip of Plastigage across each journal.

  1. A097963E01
    Install the 5 crankshaft bearing caps in their proper locations.

    NOTICE:
    Do not turn the crankshaft.

  1. A097951E01
    Install the crankshaft bearing cap bolts.

    HINT:
    1. The main bearing cap bolts are tightened in 2 progressive steps.
    2. If any of the main bearing cap bolts are broken or deformed, replace as necessary.


    1. Install and uniformly tighten the 10 main bearing cap bolts in the sequence shown in the illustration.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }

      If any one of the main bearing cap bolts does not meet the torque specification, replace the main bearing cap bolt.

    2. A099641E01
      Mark the front of the bearing cap bolts with paint.

    3. Retighten the bearing cap bolts by 90°in the numerical order above.

    4. Check that the painted mark is now at a 90°angle to the front.

  1. Remove the 10 bolts and 5 crankshaft bearing caps (above procedures).

  1. A087199E01
    A097964E01
    Measure the Plastigage at its widest point.

    Standard oil clearance:
    Item
    Standard Condition
    No. 3 journal
    0.030 to 0.055 mm (0.0012 to 0.0022 in.)
    Other journal
    0.024 to 0.049 mm (0.0009 to 0.0019 in.)

    Maximum oil clearance:
    0.10 mm (0.0039 in.)

    If the oil clearance is greater than the maximum, replace the crankshaft bearings. If necessary, replace the crankshaft.

    HINT:
    If replacing the cylinder block, the bearing standard clearance will be 0.030 to 0.055 mm (0.0012 to 0.0022 in.).

    HINT:
    If replacing a bearing, first check the number on the cylinder block for the bearing's respective journal. Then replace the bearing with one that has the same number. Each bearing's standard thickness is indicated by a 1, 2 or 3 mark on its surface.

    Cylinder block main journal bore diameter (Reference)::
    Mark
    Specified Condition
    1
    64.004 to 64.010 mm (2.5198 to 2.5201 in.)
    2
    64.011 to 64.016 mm (2.5201 to 2.5203 in.)
    3
    64.017 to 64.022 mm (2.5203 to 2.5206 in.)

    Standard bearing center wall thickness (Reference):
    Mark
    Specified Condition
    1
    1.987 to 1.990 mm (0.0782 to 0.0783 in.)
    2
    1.990 to 1.993 mm (0.0783 to 0.0785 in.)
    3
    1.993 to 1.996 mm (0.0785 to 0.0786 in.)

  1. Completely remove the Plastigage.


43. REMOVE CRANKSHAFT
  1. Lift out the crankshaft.

  1. Remove the upper bearings and upper thrust washers from the cylinder block.

    HINT:
    Arrange the main bearing caps, bearings and thrust washers in the correct order.


44. REMOVE PISTON WITH PIN

  1. G035197E02
    Check fit between the piston and piston pin.

    1. Try to move the piston back and forth on the piston pin.
      If any movement is felt, replace the piston and pin as a set.

  1. A087190E01
    Remove the piston rings.

    1. Using a piston ring expander, remove the 2 compression rings.

    2. Remove the rail and expander by hand.

      HINT:
      Arrange the piston rings in the correct order only.

  1. G035729E01
    Disconnect the connecting rod from the piston.

    1. Using a small screwdriver, pry off the snap ring from the piston.

    2. A001178E06
      Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).

    3. G036556E01
      Using a brass bar and plastic-faced hammer, lightly tap out the piston pin and remove the connecting rod.

      HINT:
      1. The piston and pin are a matched set.
      2. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.


45. REMOVE CYLINDER BLOCK WATER DRAIN COCK

46. REMOVE OIL NOZZLE
  1. Using a 5 mm hexagon wrench, remove the oil nozzle.

← DISASSEMBLY (Jun 2011 – Jul 2014)INSPECTION (Jun 2011 – Jul 2014) →