2014 Hilux · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. INSTALL CAMSHAFT TIMING GEAR

  1. A097872E01
    Put the camshaft timing gear and camshaft together by aligning the key groove and straight pin.

  1. Check that there is no gap between the gear's flange and the camshaft.

  1. With the camshaft timing gear fixed in place, tighten the flange bolt.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }


2. INSTALL VALVE STEM CAP
  1. Apply clean engine oil to the valve stem tip, and install the valve stem cap.

    NOTICE:
    Install the cap to the same place it was removed from.


3. INSTALL VALVE LASH ADJUSTER

NOTICE:
  1. Keep the lash adjuster free from dirt and foreign objects.
  2. Only use clean engine oil.

  1. A097867E01
    Place the lash adjuster into a container full of engine oil.

  1. Insert SST's tip into the lash adjuster's plunger and use the tip to press down on the checkball inside the plunger.

    SST
    09276-75010  

  1. Squeeze the SST and lash adjuster together to move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed air.

    OK:
    Plunger moves up and down.

    NOTICE:
    When bleeding high-pressure air from the compression chamber, make sure that the tip of the SST is actually pressing the checkball as shown in the illustration. If the checkball is not pressed, air will not bleed.

  1. After bleeding air, remove SST. Then, try to quickly and firmly press the plunger with a finger.

    OK:
    Plunger is very difficult to move.

    If the result is not as specified, replace the lash adjuster.

  1. Install the lash adjuster.

    HINT:
    Repeat the same procedures and install the remaining lash adjusters.

    NOTICE:
    Install the lash adjuster to the same place it was removed from.


4. INSTALL VALVE ROCKER ARM
  1. Apply clean engine oil to the valve lash adjuster tips and valve stem cap surfaces. Then install the valve rocker arms.

    NOTICE:
    Install the valve stem cap and valve rocker arm to the same place it was removed from.


5. INSTALL CAMSHAFT

  1. A097873E01
    Apply clean engine oil to the camshaft's cam portion and the cylinder head journals.

  1. Install the timing chain on the camshaft timing gear, with the painted mark of the link aligned with the timing mark of the camshaft timing gear.

  1. A097874E01
    Set the 2 camshafts as shown in the illustration.

    NOTICE:
    1. Align the paint mark and timing mark before setting the camshaft.

    2. A110967E01
      Before and after setting the camshaft and No. 2 camshaft, check that the rocker arm is firmly set to the lash adjuster.

  1. G037331E01
    Loosely install the No. 1 camshaft bearing cap.

  1. Check the proper location of each camshaft bearing cap and install each one.

  1. G037284E01
    Install a new O-ring to the No. 1 camshaft bearing cap.

  1. Temporarily install the oil delivery pipe.

  1. G037283E01
    Tighten the 21 bolts and 20 washers in the order shown in the illustration.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf } for bolt A
    15.5 N*m{ 158 kgf*cm , 11 ft.*lbf } for except bolt A


6. INSTALL CAMSHAFT TIMING SPROCKET

  1. A097877E01
    Rotate the camshaft so that the camshaft's timing mark and the No. 2 camshaft knock pin are as shown in the illustration.

  1. Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.

  1. A097878E01
    Install the timing chain on the camshaft timing sprocket, with the paint mark aligned with the timing marks on the camshaft timing sprocket.

  1. Align the No. 2 camshaft knock pin and camshaft timing sprocket's pin hole. Then install the camshaft timing sprocket to the No. 2 camshaft.

    NOTICE:
    If the knock pin and pin hole are difficult to align, slightly rotate the No. 2 camshaft to the left and right using the camshaft's hexagon-shaped part. Then attempt alignment again.

  1. A097863E02
    Fix the camshaft with a wrench, and then tighten the sprocket bolt.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }

  1. Remove the hexagon wrench from the chain tensioner.

  1. A058128E03
    Apply adhesive to 2 or 3 threads of the timing chain cover plug.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    NOTICE:
    Remove any oil from the bolt hole.

  1. Using a 10 mm socket hexagon wrench, install the timing gear case plug.

    Torque:
    16.6 N*m{ 169 kgf*cm , 12 ft.*lbf }


7. INSTALL TIMING CHAIN GUIDE

G037278E02
  1. Install a new O-ring to the camshaft bearing cap.

  1. Install the timing chain guide with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


8. INSTALL CYLINDER HEAD COVER

  1. A097879E02
    Install the 2 gaskets to the cylinder head cover.

  1. Remove any old packing (FIPG) material.

  1. Apply seal packing to 2 locations as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes after applying seal packing.
    3. Do not apply engine oil for at least 2 hours after installing.

  1. G035202E01
    Loosely install the head cover with the 19 bolts and 2 nuts.

  1. Uniformly tighten the 19 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. In numerical order, confirm that the bolts labeled 1 to 18 are tightened to the torque specification. Tighten the bolts as necessary.

  1. Connect the wire harness to the 6 clamps.


9. INSTALL IGNITION COIL
  1. Install the ignition coil with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


10. INSTALL INTAKE AIR CONNECTOR
  1. Install the intake air connector with the 2 bolts, and tighten the 2 hose clamps.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf } for intake air connector
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } for hose clamp


11. INSTALL DRIVE BELT

  1. A097752E02
    Install the drive belt to the pulleys except the drive belt tensioner pulley.

  1. Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward and then install the drive belt to the tensioner pulley.

    NOTICE:
    1. The backside of the drive belt should face the tensioner pulley.
    2. Check that the drive belt is properly set to each pulley.

  1. G038479E01
    After a new belt has been installed, check that the tensioner indicator mark is within range A shown in the illustration.


12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

13. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.


14. CHECK FOR ENGINE OIL LEAKS
  1. Start the engine, and check that there are no oil leaks after performing maintenance.


15. CHECK FOR ENGINE COOLANT LEAKS

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A099675E01
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the cylinder block and head.


16. INSPECT ENGINE IDLE SPEED AND IGNITION TIMING
  1. Warm up and stop the engine.

    NOTICE:
    A warmed up engine should have an engine coolant temperature of over 80°C (176°F), have an engine oil temperature of 60°C (140°F), and the engine rpm should be stabilized.

  1. Check the idle speed control system.

    1. G039758E01
      Using SST, connect terminals TC and CG of the DLC3.
      SST
      09843-18040  

    2. Start the engine at idle.

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connection with a wrong terminal can damage the engine.
      2. Turn off all electrical systems before connecting the terminals.
      3. When checking ISC function, the transmission should be in the neutral position.

    3. A099876E01
      After connecting terminals (TC and CG), check that the engine speed changes to approximately 1,000 to 1,500 rpm for 5 seconds, and then returns to idle speed.
      If the result is not as specified, check the throttle body, DTC (Click here) and wire harness.


17. CHECK CO/HC
  1. Start and warm up the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds and idle the engine.

  1. G037188E01
    Insert CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe.

  1. Check CO/HC concentration at idle.

    Standard idle CO concentration:
    0 to 0.5 %

    Standard idle HC concentration:
    Applicable local regulation

  1. If the CO/HC concentration is not as specified, perform troubleshooting in the order given below.

    1. Check the heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, and then inspect and repair the applicable causes if necessary.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idle
      1. Faulty ignitions:
        1. Incorrect timing
        2. Plugs are contaminated, shorted or gaps are defective
      2. Incorrect valve clearance
      3. Leaks in intake and exhaust valves
      4. Leaks in cylinders
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective ECT sensor
        3. Defective Mass Air Flow (MAF) meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor


18. CHECK FUNCTION OF THROTTLE BODY

  1. A111693
    Check the throttle control motor operating sound.

    1. Turn the ignition switch ON.

    2. When pressing the accelerator pedal, check the operating sound of the running motor. Make sure that no friction noises emit from the motor.
      If friction noise is heard, replace the throttle body.

  1. A099015E01
    Check the throttle position sensor.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch ON.

    3. Under Current Data, check that the throttle valve opening percentage (Throttle Pos) is within the standard.

      Standard throttle valve opening percentage:
      60% or more

      NOTICE:
      When checking the standard throttle valve opening percentage, the shift lever should be in the N position.

      If the percentage is less than 60%, replace the throttle body.

← INSTALLATION (Aug 2012 – Jul 2013)COMPONENTS (Jun 2011 – Jul 2012) →