2014 Hilux · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Jun 2011


INSPECT AIR CLEANER FILTER ELEMENT
  1. Remove the air filter.

  1. Visually check that the air filter is not excessively damaged or oily.
    If necessary, replace the air filter.


INSPECT V-RIBBED BELT TENSIONER

  1. G035187E01
    Idle the engine and then stop the engine. Check that the drive belt is between the edges of the tensioner pulley.

  1. Remove the drive belt from the tensioner pulley.

  1. Turn the pulley, and check that the tensioner bearing moves smoothly and quietly.
    If necessary, replace the tensioner pulley.

  1. Install the drive belt.


INSPECT NO. 1 IDLER PULLEY

  1. G035186E01
    Idle the engine and then stop the engine. Check that the drive belt is between the edges of the idler pulley.

  1. Remove the drive belt from the idler pulley.

  1. Turn the pulley, and check that the idler bearing moves smoothly and quietly.
    If necessary, replace the idler pulley.

  1. Install the drive belt.


CHECK VALVE LASH ADJUSTER NOISE
  1. Rev up the engine several times. Check that the engine does not emit unusual noises.

  1. If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then repeat the step above.

    HINT:
    If any defects or problems are found during the inspection above, perform a lash adjuster inspection (Click here).


INSPECT IGNITION TIMING
  1. Warm up the engine and stop the engine.

    NOTICE:
    A warmed up engine should have an engine coolant temperature of over 80°C (176°F), have an engine oil temperature of 60°C (140°F), and the engine rpm should be stabilized.

  1. C108852E03
    When using the intelligent tester:
    Check the ignition timing.

    1. Connect the intelligent tester to the DLC3.

    2. Start the engine at idle.

    3. Turn the intelligent tester main switch ON.

    4. Enter the following item: Powertrain / Engine and ECT / Data List / IGN Advance.

      Standard ignition timing:
      0 to 20° BTDC @ idle

      HINT:
      Please refer to the intelligent tester operator's manual for further details.

  1. G039759E01
    When not using the intelligent tester:
    Check the ignition timing.

    1. Using SST, connect tachometer probe to terminal TAC of the DLC3.

      SST
      09843-18030  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connection with a wrong terminal can damage the engine.
      2. Turn off all electrical systems before connecting the terminals.

    2. A099874E01
      Clamp the tester probe of a timing light to the 4 lead wires or green-red lead wire of the ignition coil connector for No. 1 cylinder.

    3. Start the engine.

    4. G039758E01
      Using SST, connect terminals TC and CG of the DLC3.
      SST
      09843-18040  

      NOTICE:
      When checking the ignition timing, the transmission should be in the neutral position.


      HINT:
      A099876E01
      1. After connecting terminals (TC and CG), engine rpm changes to approximately 1,000 to 1,500 rpm for 5 seconds, then returns to idle speed. Because the ECM checks that the ISC (idle speed control system) operates properly.
      2. Perform the inspection of the ignition timing after engine rpm is returned to idle speed.

    5. A099880E01
      Using a timing light, measure the ignition timing.

      Standard ignition timing:
      3 to 7° BTDC @ idle

    6. Remove the SST from terminals 13 (TC) and 4 (CG) of the DLC3.

    7. Check the ignition timing.

      Standard ignition timing:
      0 to 20° BTDC @ idle

    8. Confirm that ignition timing moves to the advanced angle side when the engine speed is increased.

    9. Remove the timing light.


INSPECT ENGINE IDLE SPEED
  1. Warm up and stop the engine.

    NOTICE:
    A warmed up engine should have an engine coolant temperature of over 80°C (176°F), have an engine oil temperature of 60°C (140°F), and the engine rpm should be stabilized.

  1. When using the intelligent tester:
    Check the idle speed.

    1. C108852E03
      Connect the intelligent tester to the DLC3.

      HINT:
      Please refer to the intelligent tester operator's manual for further details.

    2. Start the engine at idle.

    3. Turn the intelligent tester main switch ON.

    4. Enter the following item:
      Powertrain / Engine and ECT / Data List / Engine SPD.

      Standard idle speed:
      600 to 700 rpm

      NOTICE:
      1. When checking the idle speed, the transmission should be in the neutral position.
      2. Switch off all accessories and air conditioning before connecting the intelligent tester.

  1. G039759E01
    When not using the intelligent tester:
    Check the idle speed.

    1. Using SST, connect tachometer tester probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

    2. Start the engine at idle.

    3. Check the idle speed.

      Standard idle speed:
      600 to 700 rpm


INSPECT IDLE SPEED CONTROL SYSTEM
  1. Warm up and stop the engine.

    NOTICE:
    A warmed up engine should have an engine coolant temperature of over 80°C (176°F), have an engine oil temperature of 60°C (140°F), and the engine rpm should be stabilized.

  1. Check the idle speed control system.

    1. G039758E01
      Using SST, connect terminals TC and CG of the DLC3.
      SST
      09843-18040  

    2. Start the engine at idle.

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connection with a wrong terminal can damage the engine.
      2. Turn off all electrical systems before connecting the terminals.
      3. When checking ISC function, the transmission should be in the neutral position.

    3. A099876E01
      After connecting terminals (TC and CG), check that the engine speed changes to approximately 1,000 to 1,500 rpm for 5 seconds, and then returns to idle speed.
      If the result is not as specified, check the throttle body, DTC (Click here) and wire harness.


INSPECT COMPRESSION
  1. Warm up and stop the engine.

    NOTICE:
    A warmed up engine should have an engine coolant temperature of over 80°C (176°F), have an engine oil temperature of 60°C (140°F), and the engine speed should be stabilized.

  1. Disconnect the injector connectors.

  1. Remove the ignition coils.

  1. Remove the spark plugs.

  1. A099130E01
    Check the cylinder compression pressure.

    1. Insert a compression gauge into the spark plug hole.

    2. Fully open the throttle.

    3. While cranking the engine, measure the compression pressure.

      Standard compression pressure:
      1,230 kPa (12.5 kgf/cm2, 178 psi)

      Minimum pressure:
      880 kPa (9.0 kgf/cm2, 128 psi)

      Difference between each cylinder:
      68 kPa (0.7 kgf/cm2, 10 psi) or less

      NOTICE:
      1. Always use a fully charged battery to obtain an engine speed of 250 rpm or more.
      2. Check the other cylinders' compression pressure in the same way.
      3. This measurement must be done as quickly as possible.

      If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect again.

      HINT:
      1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
      2. If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage in the gasket.


CHECK CO (for Leaded Gasoline Specification Vehicle)

HINT:
This check is used only to determine whether or not the idle CO complies with regulations.

  1. Initial condition:

    1. Engine at normal operating temperature

    2. Air cleaner installed

    3. All pipes and hoses of air induction system connected

    4. All accessories switched OFF

    5. All vacuum lines properly connected

    6. SFI system wiring connectors fully seated

    7. Ignition timing set correctly

    8. Transmission in neutral position

    9. Tachometer and CO meter calibration at idle

      NOTICE:
      If a CO meter is not available, do not attempt to adjust the idle mixture. Always use a CO meter when adjusting the idle mixture. Use of the idle mixture screw for adjustments is typically not necessary if the vehicle is in good condition.

  1. Warm up the engine under constant speed (approximately 50 km/h (31 mph)). Close the throttle valve for 5 minutes after the engine coolant temperature becomes stable (80 to 90°C (176 to 194°F)) and idle the engine for 5 minutes.

  1. G037188E02
    Insert a tester probe at least 40 cm (1.3 ft.) into the tailpipe.

  1. Wait at least 1 minute before measuring to allow the concentration to stabilize. Complete the measuring within 3 minutes.

    Standard idle CO concentration:
    1.0 to 2.5 %

  1. A001435E03
    If the CO concentration does not conform to regulations, adjust by turning the idle mixture adjusting screw in the variable resistor with SST.
    SST
    09243-00020  

  1. A001434E02
    The idle mixture adjusting screw can be adjusted through an 180° angle range.
    If the CO concentration is within specification, this adjustment is complete.
    If the CO concentration cannot be corrected by idle mixture adjustment, see the table below for other possible causes.
    CO
    Problems
    Causes
    High
    Rough idle
    (black smoke from exhaust)
    1. Clogged air filter
    2. Plugged ventilation valve
    3. Faulty SFI system
      1. Faulty fuel pressure regulator
      2. Clogged fuel pressure regulator
      3. Defective engine coolant temperature (ECT) sensor
      4. Faulty ECM
      5. Faulty injectors
      6. Faulty throttle position sensor
      7. Faulty MAF meter


CHECK CO/HC (for Unleaded Gasoline Specification Vehicle)
  1. Start and warm up the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds and idle the engine.

  1. G037188E01
    Insert CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe.

  1. Check CO/HC concentration at idle.

    Standard idle CO concentration:
    0 to 0.5 %

    Standard idle HC concentration:
    Applicable local regulation

  1. If the CO/HC concentration is not as specified, perform troubleshooting in the order given below.

    1. Check the heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, and then inspect and repair the applicable causes if necessary.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idle
      1. Faulty ignitions:
        1. Incorrect timing
        2. Plugs are contaminated, shorted or gaps are defective
      2. Incorrect valve clearance
      3. Leaks in intake and exhaust valves
      4. Leaks in cylinders
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective ECT sensor
        3. Defective Mass Air Flow (MAF) meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor

← REPAIR (from Jun 2011)COMPONENTS (Jun 2011 – Jul 2012) →