2014 Hilux · Service Manual RESTRAINTS

B1800/51 Short in Driver Side Squib Circuit

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2013

Also covers:

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013

SYSTEM DESCRIPTION

The driver squib circuit consists of the center airbag sensor, spiral cable and steering pad. The circuit instructs the SRS to deploy when deployment conditions are met. These DTCs are recorded when a malfunction is detected in the driver squib circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1800/51
Center airbag sensor assembly receives line short circuit signal 5 times in driver squib circuit during primary check
  1. Steering pad (driver squib)
  2. Spiral cable
  3. Center airbag sensor assembly
  4. Instrument panel wire
B1801/51
Center airbag sensor assembly receives open circuit signal in driver squib circuit for 2 seconds
  1. Steering pad (driver squib)
  2. Spiral cable
  3. Center airbag sensor assembly
  4. Instrument panel wire
B1802/51
Center airbag sensor assembly receives short circuit to ground signal in driver squib circuit for 0.5 seconds
  1. Steering pad (driver squib)
  2. Spiral cable
  3. Center airbag sensor assembly
  4. Instrument panel wire
B1803/51
Center airbag sensor assembly receives B+ short circuit signal in driver squib circuit for 0.5 seconds
  1. Steering pad (driver squib)
  2. Spiral cable
  3. Center airbag sensor assembly
  4. Instrument panel wire

WIRING DIAGRAM

H101253E01

INSPECTION PROCEDURE


1. CHECK STEERING PAD (DRIVER SQUIB)
H101445E02
  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the steering pad.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to the spiral cable connector E.

SST
09843-18060  

CAUTION:
Never connect a tester to the steering pad (driver squib) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE:
  1. Do not forcibly insert SST into the terminals of the connector when connecting.
  2. Insert SST straight into the terminal of the connector.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1800, B1801, B1802, B1803 or 51 is not output.

    HINT:
    DTCs other than DTC B1800, B1801, B1802 or B1803 may be output at this time, but they are not related to this check.



OK
REPLACE STEERING PAD (DRIVER SQUIB)
NG


2. CHECK CONNECTOR
  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST (resistance 2.1 Ω) from the spiral cable.

  1. Check that the spiral cable connector (on the steering pad side) is not damaged.

    OK:
    Lock button is not disengaged, and claw of lock is not deformed or damaged.



NG
REPLACE SPIRAL CABLE
OK


3. CHECK DRIVER SQUIB CIRCUIT
H100367E02
  1. Disconnect the connector from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    D+ - Body ground
    Below 1 V
    D- - Body ground
    Below 1 V

  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    D+ - D-
    Below 1 Ω
    D+ - Body ground
    1 MΩ or higher
    D- - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    D+ - D-
    1 MΩ or higher



OK
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
NG


4. CHECK INSTRUMENT PANEL WIRE
H100372E02
  1. Restore the released activation prevention mechanism of connector B to its original position.

  1. Disconnect the instrument panel wire connector from the spiral cable.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A15-1 (D+) - Body ground
    Below 1 V
    A15-2 (D-) - Body ground
    Below 1 V

  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A15-1 (D+) - A15-2 (D-)
    Below 1 Ω
    A15-1 (D+) - Body ground
    1 MΩ or higher
    A15-2 (D-) - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A15-1 (D+) - A15-2 (D-)
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE SPIRAL CABLE


← B1635/24 Front Passenger Side Rear Airbag Sensor Malfunction (from Aug 2013)B1800/51 Short in Driver Side Squib Circuit (+ B1801/51, B1802/51, B1803/51) (from Aug 2013) →