2014 Hilux · Service Manual RESTRAINTS

B1805/52 Short in Front Passenger Side Squib Circuit

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2013

Also covers:

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013

SYSTEM DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor and front passenger airbag. The circuit instructs the SRS to deploy when deployment conditions are met. These DTCs are recorded when a malfunction is detected in the front passenger side squib circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1805/52
Center airbag sensor assembly receives line short circuit signal 5 times in passenger squib circuit during primary check
  1. Front passenger airbag assembly (Passenger squib)
  2. Center airbag sensor assembly
  3. Instrument panel wire
B1806/52
Center airbag sensor assembly receives open circuit signal in passenger squib circuit for 2 seconds
  1. Front passenger airbag assembly (Passenger squib)
  2. Center airbag sensor assembly
  3. Instrument panel wire
B1807/52
Center airbag sensor assembly receives short circuit to ground signal in passenger squib circuit for 0.5 seconds
  1. Front passenger airbag assembly (Passenger squib)
  2. Center airbag sensor assembly
  3. Instrument panel wire
B1808/52
Center airbag sensor assembly receives B+ short circuit signal in passenger squib circuit for 0.5 seconds
  1. Front passenger airbag assembly (Passenger squib)
  2. Center airbag sensor assembly
  3. Instrument panel wire

WIRING DIAGRAM

H101254E01

INSPECTION PROCEDURE


1. CHECK FRONT PASSENGER AIRBAG ASSEMBLY (PASSENGER SQUIB)
H101447E02
  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the front passenger airbag.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to the instrument panel wire connector E.

SST
09843-18060  

CAUTION:
Never connect a tester to the front passenger airbag (passenger squib) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE:
  1. Do not forcibly insert SST into the terminals of the connector when connecting.
  2. Insert SST straight into the terminals of the connector.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1805, B1806, B1807, B1808 or 52 is not output.

    HINT:
    DTCs other than DTC B1805, B1806, B1807, B1808 or 52 may be output at this time, but they are not related to this check.



OK
REPLACE FRONT PASSENGER AIRBAG ASSEMBLY
NG


2. CHECK CONNECTOR
  1. Turn the ignition switch OFF.

  1. Disconnect SST (resistance 2.1 Ω) from the instrument panel wire.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the instrument panel wire connectors (on the front passenger side airbag) are not damaged.

    OK:
    Lock button is not disengaged, and claw of lock is not deformed or damaged.



NG
REPAIR OR REPLACE NO. 2 INSTRUMENT PANEL WIRE
OK


3. CHECK INSTRUMENT PANEL WIRE (PASSENGER SQUIB CIRCUIT)
H100374E02
  1. Disconnect the connector from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A23-1 (P+) - Body ground
    Below 1 V
    A23-2 (P-) - Body ground
    Below 1 V

  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A23-1 (P+) - A23-2 (P-)
    Below 1 Ω
    A23-1 (P+) - Body ground
    1 MΩ or higher
    A23-2 (P-) - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A23-1 (P+) - A23-2 (P-)
    1 MΩ or higher



OK
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
NG


4. CHECK NO. 2 INSTRUMENT PANEL WIRE
H102675E04
  1. Disconnect the connector from the No. 2 instrument panel wire.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A23-1 (P+) - Body ground
    Below 1 V
    A23-2 (P-) - Body ground
    Below 1 V

  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A23-1 (P+) - IL1-2
    Below 1 Ω
    A23-2 (P-) - IL1-1
    Below 1 Ω
    A23-1 (P+) - Body ground
    1 MΩ or higher
    A23-2 (P-) - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector D (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A23-1 (P+) - A23-2 (P-)
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPAIR OR REPLACE NO. 2 INSTRUMENT PANEL WIRE


← B1800/51 Short in Driver Side Squib Circuit (+ B1801/51, B1802/51, B1803/51) (from Aug 2013)B1805/52 Short in Front Passenger Side Squib Circuit (+ B1806/52, B1807/52, B1808/52) (from Aug 2013) →