2014 Hilux · Service Manual ENGINE

HOW TO PROCEED WITH TROUBLESHOOTING

Troubleshooting · Vehicles built from Jun 2011

HINT:
*: Use the intelligent tester.

When using intelligent tester, troubleshoot in accordance with the procedures shown below.
1.VEHICLE BROUGHT TO WORKSHOP
    NEXT

    2.CUSTOMER PROBLEM ANALYSIS
      NEXT

      3.CONNECT INTELLIGENT TESTER TO DLC3*

        HINT:
        If the display indicates a communication fault with the tester, inspect the DLC3.

      NEXT

      4.CHECK DTC AND FREEZE FRAME DATA*

        HINT:
        Record or print DTCs and freeze frame data if needed.

      NEXT

      5.CLEAR DTC AND FREEZE FRAME DATA*
        NEXT

        6.CONDUCT VISUAL INSPECTION
          NEXT

          7.SET CHECK MODE DIAGNOSIS*
            NEXT

            8.CONFIRM PROBLEM SYMPTOMS

              HINT:
              If the engine does not start, first perform the "check DTC" procedures and "conduct basic inspection" procedures below.

              Result:
              Result
              Proceed to
              Malfunction does not occur
              A
              Malfunction occurs
              B


            B.
            A

            9.SIMULATE SYMPTOMS
              NEXT

              10.CHECK DTC*

                Result:
                Result
                Proceed to
                DTC is output
                A
                DTC is not output
                B


              B.
              A

              11.REFER TO DTC CHART
                NEXT

                12.CONDUCT BASIC INSPECTION

                  Result:
                  Result
                  Proceed to
                  Malfunctioning parts not confirmed
                  A
                  Malfunctioning parts confirmed
                  B


                B.
                A

                13.REFER TO PROBLEM SYMPTOMS TABLE

                  Result:
                  Result
                  Proceed to
                  Malfunctioning circuit confirmed
                  A
                  Malfunctioning parts confirmed
                  B


                B.
                A

                14.CHECK ECM POWER SOURCE CIRCUIT
                1. Check the ECM power source circuit (Click here).

                NEXT

                15.CONDUCT CIRCUIT INSPECTION

                  Result:
                  Result
                  Proceed to
                  Malfunction not confirmed
                  A
                  Malfunction confirmed
                  B


                B.
                A

                16.CHECK FOR INTERMITTENT PROBLEMS
                  NEXT

                  17.CONDUCT PARTS INSPECTION
                    NEXT

                    18.IDENTIFY PROBLEM
                      NEXT

                      19.ADJUST AND/OR REPAIR
                        NEXT

                        20.CONDUCT CONFIRMATION TEST
                          NEXT

                          When not using intelligent tester, troubleshoot in accordance with the procedures shown below.
                          1.VEHICLE BROUGHT TO WORKSHOP
                            NEXT

                            2.CUSTOMER PROBLEM ANALYSIS
                              NEXT

                              3.CHECK AND CLEAR DTC
                                NEXT

                                4.CONFIRM PROBLEM SYMPTOMS

                                  Result:
                                  Result
                                  Proceed to
                                  Malfunction occurs
                                  A
                                  Malfunction does not occur
                                  B


                                B.
                                A

                                5.CHECK DTC

                                  Result:
                                  Result
                                  Proceed to
                                  DTC is output
                                  A
                                  DTC is not output
                                  B


                                B.
                                A

                                6.REFER TO DTC CHART
                                  NEXT

                                  7.CONDUCT BASIC INSPECTION

                                    Result:
                                    Result
                                    Proceed to
                                    Malfunctioning parts not confirmed
                                    A
                                    Malfunctioning parts confirmed
                                    B


                                  B.
                                  A

                                  8.REFER TO PROBLEM SYMPTOMS TABLE

                                    Result:
                                    Result
                                    Proceed to
                                    Malfunctioning circuit confirmed
                                    A
                                    Malfunctioning parts confirmed
                                    B


                                  B.
                                  A

                                  9.CHECK ECM POWER SOURCE CIRCUIT
                                  1. Check the ECM power source circuit (Click here).

                                  NEXT

                                  10.CONDUCT CIRCUIT INSPECTION

                                    Result:
                                    Result
                                    Proceed to
                                    Malfunction not confirmed
                                    A
                                    Malfunction confirmed
                                    B


                                  B.
                                  A

                                  11.CHECK FOR INTERMITTENT PROBLEMS
                                    NEXT

                                    12.CONDUCT PARTS INSPECTION
                                      NEXT

                                      13.IDENTIFY PROBLEM
                                        NEXT

                                        14.ADJUST AND/OR REPAIR
                                          NEXT

                                          15.CONDUCT CONFIRMATION TEST
                                            NEXT

                                            ← SYSTEM DIAGRAM (from Jun 2011)CHECK FOR INTERMITTENT PROBLEMS (Jun 2011 – Jul 2012) →