DATA LIST / ACTIVE TEST
System information · Vehicles built from Jun 2011
| READ DATA LIST |
- HINT:
- Using the intelligent tester's Data List allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List.

- HINT:
- To display the entire Data List, press the pull down menu button next to Primary. Then select All Data.
Read the Data List on the tester's screen.
*: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed
Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed
Speed indicated on speedometer
Engine Speed
Engine speed/
Min.: 0 rpm, Max.: 16383.75 rpm
650 to 750 rpm: Idle after engine warmed up
-
Calculate Load
ECM calculated load/
Min.: 0%, Max.: 100%
- 11.4 to 16.4%: Idle (A/C OFF and shift position N)
- 13.1 to 18.9%: 2500 rpm (A/C OFF and shift position N)
-
Vehicle Load
Vehicle load/
Min.: 0%, Max.: 25700%
Actual vehicle load
-
MAF
Air flow rate from MAF meter/
Min.: 0 gm/s, Max.: 655.35 gm/s
- 3.2 to 4.7 gm/s: Idling
- 13.1 to 18.9 gm/s: 2500 rpm
If the value is approximately 0.0 gm/sec.: - Mass air flow meter power source circuit is open
- VG circuit is open or shorted
- E2G circuit is open
Coolant Temp
Engine coolant temperature/
Min.: -40°C (-40°F)
Max.: 140°C (284°F)
After warming up the engine:
80 to 95°C (176 to 203°F)
- If the value is -40°C (-40°F): sensor circuit is open
- If the value is 140°C (284°F): sensor circuit is shorted
Intake Air
Intake air temperature/
Min.: -40°C (-40°F)
Max.: 140°C (284°F)
Equivalent to ambient air temperature
- If the value is -40°C (-40°F): sensor circuit is open
- If the value is 140°C (284°F): sensor circuit is shorted
Engine Run Time
Engine run time/
Min.: 0 s
Max.: 65535 s
Time after engine start
Service data
Initial Engine Coolant Temp
Initial engine coolant temperature/
Min.: -40°C, Max.: 120°C
Close to ambient temperature
Service data
Initial Intake Air Temp
Initial intake air temperature/
Min.: -40°C, Max.: 120°C
Close to ambient temperature
Service data
Battery Voltage
Battery voltage/
Min.: 0 V, Max.: 65.535 V
Idling: 9 to 14 V
(Inspection mode)
-
Accel Sens. No.1 Volt %
Absolute accelerator pedal position No. 1/
Min.: 0%, Max.: 100%
10 to 22%: accelerator pedal is released
54 to 86%: accelerator pedal is fully depressed
-
Accel Sens. No.2 Volt %
Absolute accelerator pedal position No. 2/
Min.: 0%, Max.: 100%
12 to 42%: accelerator pedal is released
66 to 98%: accelerator pedal is fully depressed
-
Accel Sensor Out No.1
Accelerator pedal position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.9 V
-
ETCS freeze data
Accel Sensor Out No.2
Accelerator pedal position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.9 V
-
ETCS freeze data
Accel Sensor Out No.1
Accelerator pedal position sensor No. 1 output voltage/
Min.: 0 V, Max.: 5 V
- 0.4 to 1.4 V: Accelerator pedal released
- 3.1 to 4.6 V: Accelerator pedal fully depressed
-
Accel Sensor Out No.2
Accelerator pedal position sensor No. 2 output voltage/
Min.: 0 V, Max.: 5 V
- 1.0 to 2.2 V: Accelerator pedal released
- 3.9 to 5.0 V: Accelerator pedal fully depressed
-
Accelerator Idle Position
Whether or not accelerator pedal position sensor detecting idle/
ON or OFF
ON: Idling
-
Accel Fully Close #1 (AD)
Accelerator fully closed value No. 1 (AD)/
Min.: 0 V, Max.: 4.98 V
-
ETCS service data
Accel Fully Close Learn #1
Accelerator fully closed learned value No. 1/
Min.: 0 deg, Max.: 124.5 deg
-
ETCS service data
Accel Fully Close Learn #2
Accelerator fully closed learned value No. 2/
Min.: 0 deg, Max.: 124.5 deg
-
ETCS service data
Throttle Sensor Volt %
Absolute throttle position sensor/
Min.: 0%, Max.: 100%
- Accelerator pedal released: 10 to 22%
- Accelerator pedal fully depressed: 64 to 96%
The calculated value based on VTA1
Throttl Sensor #2 Volt %
Throttle sensor positioning #2/
Min.: 0%, Max.: 100%
- Accelerator pedal released: 42 to 62%
- Accelerator pedal fully depressed: 92 to 100%
The calculated value based on VTA2
ST1
Brake pedal signal/
ON or OFF
ON: Brake pedal depressed
-
System Guard
System guard/
ON or OFF
-
ETCS service data
Open Side Malfunction
Open side malfunction/
ON or OFF
-
ETCS service data
Throttle Idle Position
Whether or not throttle position sensor is detecting idle/
ON or OFF
Accelerator pedal released: ON
Accelerator pedal depressed: OFF
-
Throttle Require Position
Throttle requirement position/
Min.: 0 V, Max.: 4.9 V
Idling: 0.5 to 1.1 V
-
Throttle Sensor Position*
Throttle sensor positioning/
Min.: 0%, Max.: 100%
Throttle fully closed: 0%
Throttle fully open: 50 to 80%
Recognition value for throttle opening angle on ECM
Throttle Position No. 1
Throttle position No. 1/
Min.: 0 V, Max.: 4.98 V
-
ETCS freeze data
Throttle Position No. 2
Throttle position No. 2/
Min.: 0 V, Max.: 4.98 V
-
ETCS freeze data
Throttle Position No. 1
Throttle position No. 1/
Min.: 0 V, Max.: 5 V
- Accelerator pedal released: 0.5 to 1.1 V
- Accelerator pedal fully depressed: 3.2 to 4.8 V
- Fail-safe: 0.6 to 1.4 V
-
Throttle Position No. 2
Throttle position No. 2/
Min.: 0 V, Max.: 5 V
- Accelerator pedal released: 2.1 to 3.1 V
- Accelerator pedal fully depressed: 4.6 to 5.0 V
- Fail-safe: 2.1 to 3.1 V
Read the value with intrusive operation (Active Test)
Throttle Position Command
Throttle position command value/
Min.: 0 V, Max.: 4.9 V
0.5 to 4.8 V
ETCS service data
Throttle Sens Open Pos #1
Throttle sensor opener position No. 1/ Min.: 0, Max.: 4.9 V
0.6 to 1.4 V
ETCS service data
Throttle Sens Open Pos #2
Throttle sensor opener position No. 2/ Min.: 0, Max.: 4.9 V
1.7 to 2.5 V
ETCS service data
Throttle Sens Open #1 (AD)
Throttle sensor opener position No. 1 (AD)/
Min.: 0 V, Max.: 4.9 V
0.5 to 4.8 V
-
Throttle Motor
Whether or not throttle motor control is permitted/ ON or OFF
- Ignition switch ON: ON
- ETCS has failed: OFF
-
Throttle Motor Current
Throttle motor current/
Min.: 0 A, Max.: 20 A
Idling: 0 to 3.0 A
-
Throttle Motor DUTY
Throttle motor/
Min.: 0%, Max.: 100%
Idling after engine warmed up: 10 to 22%
ETCS service data
Throttle Motor Current
Throttle motor current/
Min.: 0 A, Max.: 19.9 A
-
ETCS service data
Throttle Motor Open Duty
Throttle motor duty ratio/
Min.: 0%, Max.: 100%
-
ETCS service data
Throttle Motor Close Duty
Throttle motor duty ratio/
Min.: 0%, Max.: 100%
-
ETCS service data
Throttle Motor Duty (Open)
Throttle motor duty ratio (open)/
Min.: 0%, Max.: 100%
Idling: 0 to 40%
ETCS service data
Throttle Motor Duty (Close)
Throttle motor duty ratio (close)/
Min.: 0%, Max.: 100%
Idling: 0 to 40%
ETCS service data
Throttle Fully Close Learn
Throttle fully closed (learned value)/
Min.: 0 V, Max.: 4.98 V
Accelerator pedal released: 0.4 to 1.0 V
-
ETCS Actuator Power
Whether or not electric throttle control system power is input/
ON or OFF
- Ignition switch ON and system normal: ON
- ETCS has failed: OFF
-
+BM Voltage
+BM voltage/
Min.: 0 V, Max.: 19.9 V
Ignition switch ON and system normal: 11 to 14 V
ETCS service data
Actuator Power Supply
Actuator power supply/
ON or OFF
Idling ON
(Inspection mode)
ETCS service data
Clutch Current
Clutch current/
Min.: 0 A, Max.: 2.49 A
-
ETCS service data
Electromagnetic Clutch
Electromagnetic clutch/
ON or OFF
-
-
Fail Safe Drive
Whether or not fail-safe function is executed/ ON or OFF
- ETCS has failed: ON
- ETCS normal: OFF
-
Fail Safe Drive (Main CPU)
Whether or not fail-safe function is executed/ ON or OFF
- ETCS has failed: ON
- ETCS normal: OFF
-
Injector (Port)
Injection period of the No. 1 cylinder/
Min.: 0 ms, Max.: 32.64 ms
1.3 to 2.8 ms: Idling
-
Injection Volum (Cylinder 1)
Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml
0 to 0.5 ml
The total fuel injection volume of 10 injections.
Fuel Pump Speed Control
Fuel pump speed control status/
ON or OFF
Idling: ON
Active Test support data
Fuel Pump/Speed Status
Fuel pump/speed status/
ON or OFF
Idling: ON
(Inspection mode)
-
EVAP (Purge) VSV
Purge VSV control duty/
Min.: 0%, Max.: 100%
0 to 100%: During idling
The order signal from the ECM.
Evap Purge Flow
Purge flow/
Min.: 0%, Max.: 102.3%
0 to 100%: During idling
-
Purge Density Learn Value
Learning value of purge density/
Min.: -50%, Max.: 349.99%
-40 to 0%: Idling
Service data
EVAP Purge VSV
VSV status for EVAP control/
ON or OFF
-
Active Test support data
Target Air-Fuel Ratio
Air-fuel ratio/
Min.: 0, Max.: 1.998
Idling: 0.8 to 1.2
-
AF Lambda B1S1
Short-term fuel trim associated with bank 1 sensor 1/
Min.: 0%, Max.: 1.99
- Value less than 1 (0.000 to 0.999) = Rich
- Stoichiometric air-fuel ratio = 1
- Value greater than 1 (1.001 to 1.999) = Lean
-
AF Lambda B2S1
Short-term fuel trim associated with bank 2 sensor 1/
Min.: 0%, Max.: 1.99
- Value less than 1 (0.000 to 0.999) = Rich
- Stoichiometric air-fuel ratio = 1
- Value greater than 1 (1.001 to 1.999) = Lean
-
AFS Voltage B1S1
A/F sensor output voltage for bank 1 sensor 1/
Min.: 0 V, Max.: 7.99 V
Idling: 2.8 to 3.8 V
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
AFS Voltage B2S1
A/F sensor output voltage for bank 2 sensor 1/
Min.: 0 V, Max.: 7.99 V
Idling: 2.8 to 3.8 V
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
AFS Current B1S1
Air fuel ratio sensor current for bank 1 sensor 1/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of sensor
AFS Current B2S1
Air fuel ratio sensor current for bank 2 sensor 1/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of sensor
O2S B1S2
Heated oxygen sensor output voltage for bank 1 sensor 2/
Min.: 0 V, Max.: 1.27 V
Driving 70 km/h (44 mph): 0.1 to 0.9 V
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
O2S B2S2
Heated oxygen sensor output voltage for bank 2 sensor 2/
Min.: 0 V, Max.: 1.27 V
Driving 70 km/h (44 mph): 0.1 to 0.9 V
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
Short FT #1
Short-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
-20 to 20%
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #1
Long-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
-20 to 20%
Overall fuel compensation carried out in long-term to compensate for continual deviation of short-term fuel trim from central value
Total FT #1
Total fuel trim of bank 1/
Min.: -0.5, Max.: 0.496
-0.2 to 0.2: Idling
-
Short FT #2
Short-term fuel trim of bank 2/
Min.: -100%, Max.: 99.2%
-20 to 20%
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #2
Long-term fuel trim of bank 2/
Min.: -100%, Max.: 99.2%
-20 to 20%
Overall fuel compensation carried out in long-term to compensate for continual deviation of short-term fuel trim from central value
Total FT #2
Total fuel trim of bank 2/
Min.: -0.5, Max.: 0.496
-0.2 to 0.2: Idling
-
Fuel System Status #1
Fuel system status (Bank 1)/
Unused, OL, CL, OL Drive, OL Fault or CL Fault
Idling after warming up: CL
(Inspection mode)
- OL (Open Loop): Has not yet satisfied conditions to go closed loop
- CL (Closed Loop): Feedback for fuel control.
- OL DRIVE: Open loop due to driving conditions (fuel enrichment)
- OL FAULT: Open loop due to detected system fault
- CL FAULT: Closed loop but air fuel ratio sensor which is used for fuel control is malfunctioning
Fuel System Status #2
Fuel system status (Bank 2)/
Unused, OL, CL, OL Drive, OL Fault or CL Fault
Idling after warming up: CL
(Inspection mode)
- OL (Open Loop): Has not yet satisfied conditions to go closed loop
- CL (Closed Loop): Feedback for fuel control.
- OL DRIVE: Open loop due to driving conditions (fuel enrichment)
- OL FAULT: Open loop due to detected system fault
- CL FAULT: Closed loop but air fuel ratio sensor which is used for fuel control is malfunctioning
IGN Advance
Ignition timing advance for No. 1 cylinder/
Min.: -64 deg, Max.: 63.5 deg
BTDC 7 to 24°: Idling (A/C OFF, shift position N)
-
Knock Feedback Value
Feedback value of knocking/
Min.: -64° CA, Max.: 1983.9° CA
-22 to 0 crankshaft angle: Driving, 70 km/h (44 mph)
Service data
Knock Correct Learn Value
Learned knocking correction value/
Min.: -64° CA, Max.: 1983.9° CA
0 to 22 crankshaft angle: Driving, 70 km/h (44 mph)
Service data
ACIS VSV
VSV for ACIS/
ON or OFF
-
Active Test support data
VVT Control Status #1
VVT control status (Bank 1)/
ON or OFF
-
Support for VVT Active Test
VVT Control Status #2
VVT control status (Bank 2)/
ON or OFF
-
Support for VVT Active Test
VVT Aim Angle #1
VVT aim angle (Bank 1)/
Min.: 0%, Max.: 100%
Idling: 0%
VVT duty signal value during forcible operation
VVT Change Angle #1
VVT change angle (Bank 1)/
Min.: 0 DegFR, Max.: 60 DegFR
Idling: 0 to 5 DegFR
Displacement angle during forcible operation
VVT OCV Duty #1
VVT OCV operation duty (Bank 1)/
Min.: 0%, Max.: 100%
Idling: 0%
Requested duty value for forcible operation
VVT Aim Angle #2
VVT aim angle (Bank 2)/
Min.: 0%, Max.: 100%
Idling: 0%
VVT duty signal value during forcible operation
VVT Change Angle #2
VVT change angle (Bank 2)/
Min.: 0 DegFR, Max.: 60 DegFR
Idling: 0 to 5 DegFR
Displacement angle during forcible operation
VVT OCV Duty #2
VVT OCV operation duty (Bank 2)/
Min.: 0%, Max.: 100%
Idling: 0%
Requested duty value for forcible operation
Catalyst Temp B1S1
Calculated catalyst temperature (bank 1 sensor 1)/
Min.: -40°C, Max.: 6513.5°C
400 to 800°C: Catalyst is warmed up
-
Catalyst Temp B2S1
Calculated catalyst temperature (bank 2 sensor 1)/
Min.: -40°C, Max.: 6513.5°C
400 to 800°C: Catalyst is warmed up
-
Catalyst Temp B1S2
Calculated catalyst temperature (bank 1 sensor 2)/
Min.: -40°C, Max.: 6513.5°C
400 to 800°C: Catalyst is warmed up
-
Catalyst Temp B2S2
Calculated catalyst temperature (bank 2 sensor 2)/
Min.: -40°C, Max.: 6513.5°C
400 to 800°C: Catalyst is warmed up
-
Starter Signal
Starter signal/ ON or OFF
ON: Cranking
-
Power Steering Signal
Power steering signal/ ON or OFF
ON: Power steering operation
-
Power Steer. Sig. Record
Power steering signal (history)/ ON or OFF
ON: When steering wheel first turned after battery connected
Signal status usually ON until battery disconnected
Neutral Position SW Signal
PNP switch/
ON or OFF
ON: Shift position is P or N
For automatic transmission
Stop Light Switch
Stop light switch/ ON or OFF
ON: Brake pedal is depressed
-
A/C Signal
A/C Signal/ ON or OFF
ON: A/C switch is turned ON
-
Closed Throttle Position SW
Closed throttle position switch (idle switch)/ ON or OFF
ON: Throttle valve is closed
-
Electrical Load Signal
Electrical load signal/ ON or OFF
ON: Headlights or defogger is turned ON
-
Check Mode
Check mode/ ON or OFF
Check mode ON: ON
-
SPD Test Result
Check mode result for vehicle speed sensor/
Compl or Incmpl
-
-
Misfire Test Result
Check mode result for misfire monitor/
Compl or Incmpl
-
-
OXS1 Test Result
Check mode result for HO2 sensor/
Compl or Incmpl
-
-
OXS2 Test Result
Check mode result for HO2 sensor/
Compl or Incmpl
-
-
A/F Test Result #2
Check mode result for air-fuel ratio sensor/
Compl or Incmpl
-
-
A/F Test Result #1
Check mode result for air-fuel ratio sensor/
Compl or Incmpl
-
-
Complete Parts Monitor
Complete parts monitor/
Not Avl or Avail
-
-
Fuel System Monitor
Fuel system monitor/
Not Avl or Avail
-
-
Misfire Monitor
Misfire monitor/
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT Monitor/ Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT Monitor/ Compl or Incmpl
-
-
O2S(A/FS) Heater Monitor
O2S(A/FS) Heater Monitor/ Not Avl or Avail
-
-
O2S(A/FS) Heater Monitor
O2S(A/FS) Heater Monitor/ Compl or Incmpl
-
-
O2S (A/FS) Monitor
O2S (A/FS) monitor/ Not Avl or Avail
-
-
O2S (A/FS) Monitor
O2S (A/FS) monitor/ Compl or Incmpl
-
-
A/C Monitor
A/C Monitor/ Not Avl or Avail
-
-
A/C Monitor
A/C Monitor/ Compl or Incmpl
-
-
2nd Air Monitor
2nd Air Monitor/ Not Avl or Avail
-
-
2nd Air Monitor
2nd Air Monitor/ Compl or Incmpl
-
-
EVAP Monitor
EVAP Monitor/ Not Avl or Avail
-
-
EVAP Monitor
EVAP Monitor/ Compl or Incmpl
-
-
Heated Catalyst Monitor
Heated Catalyst Monitor/ Not Avl or Avail
-
-
Heated Catalyst Monitor
Heated Catalyst Monitor/ Compl or Incmpl
-
-
Catalyst Monitor
Catalyst monitor/ Not Avl or Avail
-
-
Catalyst Monitor
Catalyst monitor/ Compl or Incmpl
-
-
# Codes (Include History)
Number of codes/
Min.: 0, Max.: 255
-
Number of detected DTCs
MIL
MIL status/ ON or OFF
MIL ON: ON
-
MIL ON Run Distance
Distance traveled while MIL is activated/
Min.: 0 km, Max.: 65,535 km
Distance after DTC is detected
-
Running Time from MIL ON
Running time from MIL ON/
Min.: 0 min, Max.: 65535 min
Equivalent to running time after MIL is turned on
-
Time after DTC Cleared
Time after DTC cleared/
Min.: 0 min
Max.: 65535 min
Equivalent to time after DTC is cleared
-
Distance from DTC Cleared
Distance after DTC cleared/
Min.: 0 km, Max.: 65535 km
Equivalent to distance driven after DTC is cleared
-
Warmup Cycle Cleared DTC
Warmup cycle after DTC cleared/
Min.: 0, Max.: 255
-
Number of warmup cycles after DTC is cleared
OBD Requirements
OBD Requirements
EOBD (Euro OBD)
-
Number of Emission DTC
Number of emission DTCs
-
-
TC and TE1
TC and TE1 terminal of DLC3/
ON or OFF
-
-
Ignition Trig. Count
Ignition counter/
Min.: 0, Max.: 65535
0 to 600
-
Cylinder #1 Misfire Count
Misfire ratio of cylinder 1/
Min.: 0, Max.: 255
0
-
Cylinder #2 Misfire Count
Misfire ratio of cylinder 2/
Min.: 0, Max.: 255
0
-
Cylinder #3 Misfire Count
Misfire ratio of cylinder 3/
Min.: 0, Max.: 255
0
-
Cylinder #4 Misfire Count
Misfire ratio of cylinder 4/
Min.: 0, Max.: 255
0
-
Cylinder #5 Misfire Count
Misfire ratio of cylinder 5/
Min.: 0, Max.: 255
0
-
Cylinder #6 Misfire Count
Misfire ratio of cylinder 6/
Min.: 0, Max.: 255
0
-
All Cylinders Misfire Count
Misfire count of all cylinders/
Min.: 0, Max.: 255
0 to 35
-
Misfire RPM
Engine speed for first misfire range/
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: Misfire 0
-
Misfire Load
Engine load for first misfire range/
Min.: 0 g/rev, Max.: 3.98 g/rev
0 g/rev: Misfire 0
-
Misfire Margin
Misfire monitoring/
Min.: -128%, Max.: 127%
-100 to 99.22%
Misfire detecting margin
ACT VSV
A/C cut status for Active Test/
ON or OFF
-
Active Test support data
Idle Fuel Cut
Fuel cut idle/ ON or OFF
Fuel cut operation: ON
Idle Fuel Cut = "ON" when throttle valve is fully closed and engine speed is over 2800 rpm
FC TAU
Fuel cut TAU: Fuel cut during very light load/ ON or OFF
Fuel cut operating: ON
The fuel cut is being performed under very light load to prevent the engine combustion from becoming incomplete
Model Code
Model code
-
Identifying the model code:
GGN###
Engine Type
Engine type
-
Identifying the engine type:
1GRFE
Cylinder Number
Cylinder number/
Min.: 0, Max.: 255
-
Identifying the cylinder number:
6
Transmission Type
Transmission type
-
Identifying the transmission type:
ECT 5th
Destination
Destination
-
Identifying the destination:
W
Model Year
Model year/
Min.: 1900, Max.: 2155
-
Identifying the model year:
20##
System Identification
System identification
-
Identifying the engine system:
Gasoline (gasoline engine)
- HINT:
- Normal Condition: If no conditions are specifically stated for "Idling", the shift lever is on neutral, the A/C switch is OFF and all accessory switches are OFF.
- 11.4 to 16.4%: Idle (A/C OFF and shift position N)
| PERFORM ACTIVE TEST |
- HINT:
- Performing the intelligent tester's Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.
- The Data List can be displayed during the Active Test.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the tester, perform the Active Test.
Tester Display
Test Part
Control Range
Diagnostic Note
Control the Injection Volume
Control injection volume
(Engine speed: 3000 rpm or less)
Min.: -12.5%, Max.: 24.8%
- All injectors are tested at once
- Injection volume is gradually changed between -12.5% and 24.8%
Control the Injection Volume for A/F Sensor
Change injection volume
Decreases by -12.5% or increases by 25%
Following A/F Control procedure enables technician to check and graph output voltages of both A/F sensor and heated oxygen sensor.
To display graph indication, select following menu items: View / Line graph 1 or Line graph 2.
Activate the Fuel Pump Speed Control
Fuel pump speed control
ON (low speed)/OFF (high speed)
-
Activate the VSV for Intake Control
VSV for ACIS
ON or OFF
-
Activate the VSV for Evap Control
Activate purge VSV control
ON or OFF
-
Control the A/C Cut Signal
Control A/C cut signal
ON or OFF
-
Control the Fuel Pump / Speed
Control fuel pump
ON or OFF
Engine is stopped
Connect the TC and TE1
Connect TC and TE1
ON or OFF
-
Control the Idle Fuel Cut Prohibit
Control idle fuel cut prohibition
ON or OFF
During idling
Control the ETCS Open/Close Slow Speed
Control the ETCS opening/closing slow speed
Open or Close
Test possible when following conditions met: - Ignition switch ON
- Engine is stopped
- Accelerator pedal is fully depressed
Control the ETCS Open/Close Fast Speed
Control the ETCS opening/closing fast speed
Open or Close
Test possible when following conditions met: - Ignition switch ON
- Engine is stopped
- Accelerator pedal is fully depressed
Control the VVT Linear (Bank 1)
Control the VVT (Bank 1)
Min.: -128%, Max.: 127%
-
Control the VVT System (Bank 1)
Control VVT system (Bank 1)
ON or OFF
- ON: Rough idle or engine stall
- OFF: Normal engine speed
- Vehicle is stopped
- Engine idling
Control the VVT Linear (Bank 2)
Control the VVT (Bank 2)
Min.: -128%, Max.: 127%
-
Control the VVT System (Bank 2)
Control VVT system (Bank 2)
ON or OFF
- ON: Rough idle or engine stall
- OFF: Normal engine speed
- Vehicle is stopped
- Engine idling
Control the Cylinder #1 Fuel Cut
Control the cylinder #1 fuel cut
ON or OFF
Cylinder No. 1 fuel cut for power balance - Vehicle is stopped
- Engine idling
Control the Cylinder #2 Fuel Cut
Control the cylinder #2 fuel cut
ON or OFF
Cylinder No. 2 fuel cut for power balance - Vehicle is stopped
- Engine idling
Control the Cylinder #3 Fuel Cut
Control the cylinder #3 fuel cut
ON or OFF
Cylinder No. 3 fuel cut for power balance - Vehicle is stopped
- Engine idling
Control the Cylinder #4 Fuel Cut
Control the cylinder #4 fuel cut
ON or OFF
Cylinder No. 4 fuel cut for power balance - Vehicle is stopped
- Engine idling
Control the Cylinder #5 Fuel Cut
Control the cylinder #5 fuel cut
ON or OFF
Cylinder No. 5 fuel cut for power balance - Vehicle is stopped
- Engine idling
Control the Cylinder #6 Fuel Cut
Control the cylinder #6 fuel cut
ON or OFF
Cylinder No. 6 fuel cut for power balance - Vehicle is stopped
- Engine idling
Control the All Cylinders Fuel Cut
All cylinder fuel cut
ON/OFF
Test possible while vehicle stopped and engine idling.
- All injectors are tested at once