P0351/14 Ignition Coil "A" Primary / Secondary Circuit
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Also covers:
- P0352/15 Ignition Coil "B" Primary / Secondary Circuit
- P0353/14 Ignition Coil "C" Primary / Secondary Circuit
- P0354/15 Ignition Coil "D" Primary / Secondary Circuit
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
- HINT:
- These DTCs indicate malfunctions related to the primary circuit.
- If DTC P0351/14 is displayed, check No. 1 ignition coil with igniter circuit.
- If DTC P0352/15 is displayed, check No. 2 ignition coil with igniter circuit.
- If DTC P0353/14 is displayed, check No. 3 ignition coil with igniter circuit.
- If DTC P0354/15 is displayed, check No. 4 ignition coil with igniter circuit.
- These DTCs indicate malfunctions related to the primary circuit.
The DIS is a 1 cylinder ignition system which ignites one cylinder with one ignition coil. In the 1 cylinder ignition system, one spark plug is connected to the end of the secondary winding. High-voltage is generated in the secondary winding and is applied directly to the spark plug. The spark of the spark plug passes from the center electrode to the ground electrode.
The ECM determines the ignition timing and transmits the ignition (IGT) signals for each cylinder. Using the IGT signal, the ECM turns ON and OFF the power transistor inside the igniter, which turns ON and OFF a current to the primary coil. When the current to the primary coil is cut off, high-voltage is generated in the secondary coil and this voltage is applied to the spark plugs to create sparks inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back the ignition confirmation (IGF) signal to the ECM.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0351/14 P0352/15 P0353/14 P0354/15 |
No IGF signal to ECM while engine is running |
|
MONITOR DESCRIPTION


If the ECM does not receive an IGF after sending an IGT, it interprets this as a fault in the igniter and sets a DTC. The monitor runs for 1 second (the first second of engine idle) after the engine is started.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. PERFORM SIMULATION TEST |
Clear the DTCs (Click here).
Change the arrangement of the ignition coils (with igniters).
- NOTICE:
- Do not change the location of the connectors.
Perform the simulation test.
- Result:
Display (DTC Output)
Proceed to
Cleared DTCs are output again
A
Other DTCs
B
|
|
||||
| A | |
| 2. CHECK IGNITION COIL ASSEMBLY (POWER SOURCE) |
![]() ![]() |
Disconnect the I7, I8, I9 and I10 ignition coil with igniter connectors.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
I7-4 (GND) - Body ground
Below 1 Ω
I8-4 (GND) - Body ground
Below 1 Ω
I9-4 (GND) - Body ground
Below 1 Ω
I10-4 (GND) - Body ground
Below 1 Ω
Turn the ignition switch ON.
Measure the voltage of the wire harness side connectors.
- Standard voltage:
Tester Connection
Specified Condition
I7-1 (+B) - I7-4 (GND)
11 to 14 V
I8-1 (+B) - I8-4 (GND)
11 to 14 V
I9-1 (+B) - I9-4 (GND)
11 to 14 V
I10-1 (+B) - I10-4 (GND)
11 to 14 V
|
|
||||
| NG | |
| 3. CHECK WIRE HARNESS (IGNITION COIL - ECM) |
![]() ![]() |
Disconnect the I7, I8, I9 and I10 ignition coil with igniter connectors.
Disconnect the E12 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
I7-2 - E12-23 (IGF1)
Below 1 Ω
I8-2 - E12-23 (IGF1)
Below 1 Ω
I9-2 - E12-23 (IGF1)
Below 1 Ω
I10-2 - E12-23 (IGF1)
Below 1 Ω
I7-3 - E12-17 (IGT1)
Below 1 Ω
I8-3 - E12-16 (IGT2)
Below 1 Ω
I9-3 - E12-15 (IGT3)
Below 1 Ω
I10-3 - E12-14 (IGT4)
Below 1 Ω
I7-2 or E12-23 (IGF1) - Body ground
10 kΩ or higher
I8-2 or E12-23 (IGF1) - Body ground
10 kΩ or higher
I9-2 or E12-23 (IGF1) - Body ground
10 kΩ or higher
I10-2 or E12-23 (IGF1) - Body ground
10 kΩ or higher
I7-3 or E12-17 (IGT1) - Body ground
10 kΩ or higher
I8-3 or E12-16 (IGT2) - Body ground
10 kΩ or higher
I9-3 or E12-15 (IGT3) - Body ground
10 kΩ or higher
I10-3 or E12-14 (IGT4) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK ECM (IGT1, IGT2, IGT3, IGT4, IGF1 SIGNAL) |
![]() ![]() |
While cranking or idling, check the waveform of the ECM connector using the oscilloscope.
- Standard:
Tester Connection
Specified Condition
E12-17 (IGT1) - E12-3 (E1)
Correct waveform is as shown
E12-16 (IGT2) - E12-3 (E1)
Correct waveform is as shown
E12-15 (IGT3) - E12-3 (E1)
Correct waveform is as shown
E12-14 (IGT4) - E12-3 (E1)
Correct waveform is as shown
E12-23 (IGF1) - E12-3 (E1)
Correct waveform is as shown
Tool setting
Condition
2 V/DIV., 20 msec./DIV.
Idling
- HINT:
- The wavelength becomes shorter as engine speed increases.
|
|
||||
| OK | |
| 5. CHECK IF DTC OUTPUT RECURS (IGNITION COIL - INJ FUSE) |
Clear the DTC (Click here).
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTC.
- Result:
Display (DTC Output)
Proceed to
One or more of P0351, P0352, P0353, P0354, P0355 and P0356
A
No output
B
|
|
||||
| A | ||
| ||



