P2121/19 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
DESCRIPTION
- HINT:
- This DTC is related to the accelerator pedal position sensor.
| DTC No. |
DTC Detection Condition |
Suspected Area |
| P2121/19 |
Conditions (a) and (b) continue for 0.5 seconds:
|
|
MONITOR DESCRIPTION
When the difference between voltage outputs of VPA1 and VPA2 deviates from the standard range, the ECM concludes that there is a defect in the accelerator pedal position (APP) sensor. The ECM illuminates the MIL and sets a DTC.This monitor runs for 1 second (the first second of engine idle) after the engine is started.
FAIL-SAFE
The accelerator pedal position sensor has a main circuit and associated circuit. When one circuit is malfunctioning, the accelerator pedal position is calculated by the output of the other circuit. When both of the circuits are malfunctioning, it is interpreted that the accelerator pedal is released. As a result, throttle valve is closed and engine idles.WIRING DIAGRAM
Refer to DTC P2120/19 (Click here).INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
When using intelligent tester:
| 1. READ DATA LIST (ACCELERATOR POSITION NO. 1, ACCELERATOR POSITION NO. 2) |
![]() ![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.
Read the values.
- Standard voltage:
Accelerator Pedal
Accelerator Position No. 1
Accelerator Position No. 2
Released
0.5 to 1.1 V
1.2 to 2.0 V
Depressed
2.6 to 4.5 V
3.4 to 5.0 V
|
|
||||
| NG | |
| 2. CHECK WIRE HARNESS (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() ![]() |
Disconnect the A13 accelerator pedal position sensor connector.
Disconnect the E9 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
A13-6 (VPA) - E9-18 (VPA)
Below 1 Ω
A13-5 (EPA) - E9-20 (EPA)
Below 1 Ω
A13-4 (VCPA) - E9-26 (VCPA)
Below 1 Ω
A13-3 (VPA2) - E9-19 (VPA2)
Below 1 Ω
A13-2 (EPA2) - E9-21 (EPA2)
Below 1 Ω
A13-1 (VCP2) - E9-27 (VCP2)
Below 1 Ω
A13-6 (VPA) or E9-18 (VPA) - Body ground
10 kΩ or higher
A13-5 (EPA) or E9-20 (EPA) - Body ground
10 kΩ or higher
A13-4 (VCPA) or E9-26 (VCPA) - Body ground
10 kΩ or higher
A13-3 (VPA2) or E9-19 (VPA2) - Body ground
10 kΩ or higher
A13-2 (EPA2) or E9-21 (EPA2) - Body ground
10 kΩ or higher
A13-1 (VCP2) or E9-27 (VCP2) - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
When not using intelligent tester:
| 1. CHECK ECM (VPA, VPA2 VOLTAGE) |
![]() ![]() |
Turn the ignition switch ON.
Measure the voltage of the ECM connector.
- Standard voltage:
Tester Connection
Accelerator Pedal Condition
Specified Condition
E9-18 (VPA) - E9-20 (EPA)
Released
0.5 to 1.1 V
E9-18 (VPA) - E9-20 (EPA)
Depressed
2.5 to 4.6 V
E9-19 (VPA2) - E9-21 (EPA2)
Released
1.5 to 2.9 V
E9-19 (VPA2) - E9-21 (EPA2)
Depressed
3.5 to 5.0 V
|
|
||||
| NG | |
| 2. CHECK WIRE HARNESS (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() ![]() |
Disconnect the A13 accelerator pedal position sensor connector.
Disconnect the E9 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
A13-6 (VPA) - E9-18 (VPA)
Below 1 Ω
A13-5 (EPA) - E9-20 (EPA)
Below 1 Ω
A13-4 (VCPA) - E9-26 (VCPA)
Below 1 Ω
A13-3 (VPA2) - E9-19 (VPA2)
Below 1 Ω
A13-2 (EPA2) - E9-21 (EPA2)
Below 1 Ω
A13-1 (VCP2) - E9-27 (VCP2)
Below 1 Ω
A13-6 (VPA) or E9-18 (VPA) - Body ground
10 kΩ or higher
A13-5 (EPA) or E9-20 (EPA) - Body ground
10 kΩ or higher
A13-4 (VCPA) or E9-26 (VCPA) - Body ground
10 kΩ or higher
A13-3 (VPA2) or E9-19 (VPA2) - Body ground
10 kΩ or higher
A13-2 (EPA2) or E9-21 (EPA2) - Body ground
10 kΩ or higher
A13-1 (VCP2) or E9-27 (VCP2) - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||




