2014 Hilux · Service Manual CRUISE CONTROL SYSTEM

P0571 Stop Light Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2011

DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. When the ECM receives this signal, it cancels the cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch, and the ECM turns the cruise control off.
DTC Code
DTC Detection Condition
Trouble Area
P0571
When the voltage of the STP terminal and the ST1- terminal of the ECM is below 1 V for 0.5 sec. or more.
  1. Stop light switch assembly
  2. Stop light switch circuit
  3. ECM

WIRING DIAGRAM

E149001E11

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Using the intelligent tester, read the Data List.

    Cruise Control 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    Stop Light SW M-CPU
    Stop light switch signal (Main CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

    OK:
    Display changes according to brake pedal operation described in above table.



NG
Go to step 2
OK

REPLACE ECM

2. INSPECT FUSE (STOP, IGN)
  1. Disconnect the STOP and IGN fuses from the driver side junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    STOP fuse
    Always
    Below 1 Ω
    IGN fuse



NG
REPLACE FUSE
OK


3. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. E171636E01
    Remove the stop light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin pushed
    10 kΩ or higher
    Pin not pushed
    Below 1 Ω
    3 - 4
    Pin pushed
    Below 1 Ω
    Pin not pushed
    10 kΩ or higher



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


4. CHECK HARNESS AND CONNECTOR (BATTERY - STOP LIGHT SWITCH)
E110511E11
  1. Disconnect the S14 stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S14-2 - Body ground
    Always
    11 to 14 V
    S14-3 - Body ground
    Ignition switch ON



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
E216585E01
  1. Disconnect the S14 stop light switch connector.

  1. Disconnect the E14*1, E31*2 or E6*3 ECM connector.

    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV (for DPF)
    3. *3: for 1KD-FTV (except DPF)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE:
    Tester Connection
    Condition
    Specified Condition
    S14-1 - E14-15 (STP)
    Always
    Below 1 Ω
    S14-1 - Body ground
    Always
    10 kΩ or higher
    S14-4 - E14-16 (ST1-)
    Always
    Below 1 Ω
    S14-4 - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (for DPF):
    Tester Connection
    Condition
    Specified Condition
    S14-1 - E31-8 (STP)
    Always
    Below 1 Ω
    S14-1 - Body ground
    Always
    10 kΩ or higher
    S14-4 - E31-9 (ST1-)
    Always
    Below 1 Ω
    S14-4 - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (except DPF):
    Tester Connection
    Condition
    Specified Condition
    S14-1 - E6-15 (STP)
    Always
    Below 1 Ω
    S14-1 - Body ground
    Always
    10 kΩ or higher
    S14-4 - E6-14 (ST1-)
    Always
    Below 1 Ω
    S14-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0500 Vehicle Speed Sensor Circuit Malfunction (+ P0503) (from Aug 2013)P0575 Cruise Control Input Circuit (+ P0607) (from Jun 2011) →