2014 Hilux · Service Manual BRAKE

TERMINALS OF ECU

System information · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013


CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU WITH ACTUATOR)
C108855E01
  1. Measure the voltage of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S2-1 (+BS) - S2-2, 24 (GND1, GND2)
    W-R - W-B
    Solenoid relay power supply
    Always
    10 to 14 V
    S2-3 (EXI4) - S2-2, 24 (GND1, GND2)*
    G-W - W-B
    L4 switch input
    Ignition switch ON, L4 switch ON
    Below 1.5 V
    Ignition switch ON, L4 switch OFF
    8 to 14 V
    S2-4(GL1) - S2-2, 24 (GND1, GND2)
    R - W-B
    Deceleration sensor input
    Ignition switch ON, vehicle is stopped
    0.5 to 4.5 V
    S2-7 (GGND) - S2-2, 24 (GND1, GND2)
    B - W-B
    Deceleration sensor GND
    Ignition switch OFF
    Below 1.5 V
    S2-9 (FL+) - S2-8 (FL-)
    R - G
    Front speed sensor LH input
    Ignition switch ON, slowly turn left front wheel
    Pulse generation
    S2-10 (STP) - S2-2, 24 (GND1, GND2)
    G-W - W-B
    Stop light switch input
    Stop light switch ON
    8 to 14 V
    Stop light switch OFF
    Below 1.5 V
    S2-11 (RL+) - S2-12 (RL-)
    P - L
    Rear speed sensor LH input
    Ignition switch ON, slowly turn left rear wheel
    Pulse generation
    S2-13 (WA) - S2-2, 24 (GND1, GND2)
    R-G - W-B
    ABS warning light output
    Ignition switch ON, ABS warning light ON
    9 to 14 V
    Ignition switch ON, ABS warning light OFF
    Below 1 V
    S2-14 (D/G) - S2-2, 24 (GND1, GND2)
    L-Y - W-B
    Diagnosis tester communication line
    Ignition switch ON
    10 to 14 V
    S2-15 (TS) - S2-2, 24 (GND1, GND2)
    W - W-B
    Terminal TS of DLC3
    Ignition switch OFF
    Below 1.5 V
    Ignition switch ON
    10 to 14 V
    S2-16 (TC) - S2-2, 24 (GND1, GND2)
    P-L - W-B
    Terminal TC of DLC3
    Ignition switch OFF
    Below 1.5 V
    Ignition switch ON
    10 to 14 V
    S2-17 (EXI) - S2-2, 24 (GND1, GND2)*
    R-B - W-B
    4WD w/ A. D. D. :
    1. Differential vacuum actuator switch input
    4WD w/o A. D. D. :
    1. Transfer indicator switch (4WD Position) input
    4WD w/ A. D. D. :
    1. Ignition switch ON
    2. Differential vacuum actuator switch ON
    4WD w/o A. D. D. :
    1. Ignition switch ON
    2. Transfer indicator switch (4WD Position) ON
    Below 1.5 V
    4WD w/ A. D. D. :
    1. Ignition switch ON
    2. Differential vacuum actuator switch OFF
    4WD w/o A. D. D. :
    1. Ignition switch ON
    2. Transfer indicator switch (4WD Position) OFF
    10 to 14 V
    S2-18 (PKB) - S2-2, 24 (GND1, GND2)
    L-O - W-B
    Parking brake switch input
    Ignition switch ON, parking brake switch ON
    Below 1.5 V
    Ignition switch ON, parking brake switch OFF
    10 to 14 V
    S2-22 (EXI2) - S2-2, 24 (GND1, GND2)
    V - W-B
    Transfer indicator switch (rear differential lock) input
    Ignition switch ON, rear differential lock switch ON
    Below 1 V
    Ignition switch ON, rear differential lock switch OFF
    10 to 14 V
    S2-23 (+BM) - S2-2, 24 (GND1, GND2)
    R - W-B
    Motor relay power supply
    Always
    10 to 14 V
    S2-25 (IG1) - S2-2, 24 (GND1, GND2)
    R-L - W-B
    IG1 power supply
    Ignition switch ON
    10 to 14 V
    S2-28(VGS) - S2-2, 24 (GND1, GND2)
    W - W-B
    Deceleration sensor power supply
    Ignition switch ON, vehicle is stopped
    4.75 to 5.25 V
    S2-31 (FR+) - S2-30 (FR-)
    W - R
    Front speed sensor RH input
    Ignition switch ON, slowly turn right front wheel
    Pulse generation
    S2-33 (RR+) - S2-34 (RR-)
    G - R
    Rear speed sensor RH input
    Ignition switch ON, slowly turn right rear wheel
    Pulse generation

    HINT:
    *: 4WD
    If the result is not as specified, there may be a malfunction in the skid control ECU.

← TERMINALS OF ECU (Jun 2011 – Jul 2013)DIAGNOSIS SYSTEM (from Jun 2011) →