C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2013
Also covers:
- C0215/34 Left Rear Wheel Speed Sensor Signal Malfunction
- C1238/38 Foreign Object is Attached on Tip of Rear Speed Sensor RH
- C1239/39 Foreign Object is Attached on Tip of Rear Speed Sensor LH
- C1273/73 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1274/74 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)
- C1277/77 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1278/78 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
DESCRIPTION
Refer to DTCs C0200/31, C0205/32, C1235/35 and C1236/36.DTCs C1273/73, C1274/74, C1277/77 and C1278/78 can be deleted when the speed sensor sends a vehicle speed signal or the test mode ends. DTCs C1273/73, C1274/74, C1277/77 and C1278/78 are output only in the test mode.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| C0210/33 C0215/34 |
When one of following occurs
|
|
| C1238/38 C1239/39 |
At vehicle speed of 20 km/h (12 mph) or more, condition that noise is included in speed sensor signal continues for 5 sec. or more. |
|
| C1273/73 |
Detected only during test mode |
|
| C1274/74 |
Detected only during test mode |
|
| C1277/77 |
Detected only during test mode |
|
| C1278/78 |
Detected only during test mode |
|
- HINT:
- DTCs C0210/33 and C1238/38 are for the rear speed sensor RH.
- DTCs C0215/34 and C1239/39 are for the rear speed sensor LH.
- DTCs C0210/33 and C1238/38 are for the rear speed sensor RH.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHOOSE DIAGNOSIS METHOD |
Choose the diagnosis method.
Method Method
Proceed to
Using intelligent tester
A
Not using intelligent tester
B
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR) |
Check the Data List for proper functioning of the rear speed sensor.
Skid control ECU Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
RR Wheel Speed
Wheel speed sensor (RR)
reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Speed similar to that of speedometer
RL Wheel Speed
Wheel speed sensor (RL)
reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Speed similar to that of speedometer
- OK:
- There is almost no difference between actual wheel speed and displayed speed value.
- HINT:
- There is a tolerance of +/-10% in the speedometer indication.
|
|
||||
| OK | |
| 3. INSPECT SPEED SENSOR AND SENSOR ROTOR SERRATIONS |
![]() ![]() |
Connect an oscilloscope to terminals 33 (RR+) and 34 (RR-), and 11 (RL+) and 12 (RL-) of the S2 skid control ECU connector.
Drive the vehicle at about 30 km/h (19 mph), and check the signal waveform.
- OK:
- A waveform is output, as shown in the illustration.
- HINT:
- As vehicle speed (wheel revolution speed) increases, the wavelength shortens and the fluctuation in the output voltage becomes greater.
- Scratches, looseness or foreign matter on the speed sensor rotor cause noise (errors) in the signal waveform.
- As vehicle speed (wheel revolution speed) increases, the wavelength shortens and the fluctuation in the output voltage becomes greater.
|
|
||||
| OK | ||
| ||
| 4. INSPECT REAR SPEED SENSOR |
![]() ![]() |
Disconnect the S40 and S41 rear speed sensor connectors.
Measure the resistance of the speed sensors.
- Standard resistance:
Tester Connection
Specified Condition
1 - 2
0.65 to 1.8 kΩ
1 - Body ground
10 kΩ or higher
2 - Body ground
10 kΩ or higher
- HINT:
- Check the speed sensor signal after the speed sensor replacement.
|
|
||||
| OK | |
| 5. CHECK WIRE HARNESS (SKID CONTROL ECU - REAR SPEED SENSOR) |
![]() ![]() |
Disconnect the S2 ECU connector.
Disconnect the S40 and S41 rear speed sensor connectors.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
- LH:
Tester Connection
Specified Condition
S2-11 (RL+) - S40-2
Below 1 Ω
S2-12 (RL-) - S40-1
Below 1 Ω
S40-2 - Body ground
10 kΩ or higher
S40-1 - Body ground
10 kΩ or higher
- RH:
Tester Connection
Specified Condition
S2-33 (RR+) - S41-2
Below 1 Ω
S2-34 (RR-) - S41-1
Below 1 Ω
S41-2 - Body ground
10 kΩ or higher
S41-1 - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 6. INSPECT SPEED SENSOR AND SENSOR ROTOR SERRATIONS |
![]() ![]() |
Connect an oscilloscope to terminals 33 (RR+) and 34 (RR-), and 11 (RL+) and 12 (RL-) of the S2 skid control ECU connector.
Drive the vehicle at about 30 km/h (19 mph), and check the signal waveform.
- OK:
- A waveform is output, as shown in the illustration.
- HINT:
- As vehicle speed (wheel revolution speed) increases, the wavelength shortens and the fluctuation in the output voltage becomes greater.
- Scratches, looseness or foreign matter on the speed sensor rotor cause noise (errors) in the signal waveform.
- As vehicle speed (wheel revolution speed) increases, the wavelength shortens and the fluctuation in the output voltage becomes greater.
|
|
||||
| OK | |
| 7. CHECK IF DTC OUTPUT RECURS |
Clear the DTCs.
Drive the vehicle at approximately 30 km/h (19 mph) or more for 60 seconds or more.
Check for DTCs.
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | ||
| ||
| 8. INSPECT REAR SPEED SENSOR (INSTALLATION) |
![]() ![]() |
Check the rear speed sensor installation (Click here).
- OK:
- The installation bolt is tightened properly.
There is no clearance between the sensor and rear axle housing.
- HINT:
- Check the speed sensor signal after the speed sensor replacement.
|
|
||||
| OK | |
| 9. INSPECT REAR SPEED SENSOR (TIP) |
Remove the rear speed sensor.
Check the sensor tip.
- OK:
- No scratches or foreign matter on sensor tip.
- HINT:
- If the sensor is contaminated with oil or other foreign material, clean the sensor.
- If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.
- Check the speed sensor signal after cleaning or replacing the speed sensor.
- If the sensor is contaminated with oil or other foreign material, clean the sensor.
- NOTICE:
- Do not replace the speed sensor if no damage to the speed sensor tip is found.
|
|
||||
| OK | |
| 10. INSPECT SPEED SENSOR ROTOR |
Remove the rear axle shaft with backing plate.
Check the sensor rotor serrations.
- OK:
- No scratches, missing teeth or foreign matter on sensor rotor.
- HINT:
- If foreign matter is attached, remove it and check the output waveform after reassembly.
- Check the speed sensor signal after cleaning or replacing the speed sensor rotor.
- If foreign matter is attached, remove it and check the output waveform after reassembly.
|
|
||||
| OK | |
| 11. CHECK IF DTC OUTPUT RECURS |
Clear the DTCs.
Drive the vehicle at approximately 30 km/h (19 mph) or more for 60 seconds or more.
Check for DTCs.
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | ||
| ||




