2014 Hilux · Service Manual BRAKE

ADJUSTMENT

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Jun 2011 – Jul 2014 from Aug 2014


1. CHECK AND ADJUST BRAKE PEDAL HEIGHT

C194288E01
  1. Check the pedal height.

    Pedal height from dash panel:
    Item
    Specified Condition
    LHD (M/T)
    168.3 to 178.3 mm (6.626 to 7.019 in.)
    LHD (A/T)
    169.3 to 179.3 mm (6.666 to 7.059 in.)
    RHD (M/T)
    156.9 to 166.9 mm (6.177 to 6.571 in.)
    RHD (A/T)
    158.1 to 168.1 mm (6.224 to 6.618 in.)

  1. Adjust the pedal height.

    1. Disconnect the connector from the stop light switch.

    2. Remove the switch.

    3. Loosen the push rod clevis lock nut.

    4. Adjust the pedal height by turning the push rod.

    5. Tighten the lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    6. C111301E04
      Insert the switch into the adjuster until it slightly touches the pedal.

      NOTICE:
      Do not depress the pedal.

    7. C111302E03
      Turn the switch a quarter turn clockwise.

      Torque:
      1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

      NOTICE:
      Do not depress the pedal.

    8. Connect the connector to the switch.

    9. Check the switch clearance.

      Stop light switch clearance:
      1.5 to 2.5 mm (0.0591 to 0.0984 in.)


2. CHECK BRAKE PEDAL FREE PLAY

C111306E02
  1. Stop the engine. Depress the pedal several times until there is no vacuum in the booster. Then release the pedal.

  1. Depress the pedal until resistance is felt.

  1. Check the pedal free play by measuring the distance between the position in the previous step and the pedal's released position.

    Pedal free play:
    1.0 to 6.0 mm (0.0394 to 0.236 in.)

    If the free play is not as specified, check the switch clearance in the next step.
    If the free play is as specified, proceed to the "check brake pedal reserve distance" procedure.

  1. Check the switch clearance.

    Stop light switch clearance:
    1.5 to 2.5 mm (0.0591 to 0.0984 in.)

    If the clearance is not as specified, adjust the clearance and recheck the pedal free play.
    If the clearance is as specified, troubleshoot the brake system and proceed to the "check brake pedal reserve distance" procedure.


3. CHECK BRAKE PEDAL RESERVE DISTANCE

C111339E08
  1. Release the parking brake lever. Start the engine.

  1. Depress the pedal and check the pedal reserve distance.

    1. Depress the pedal with a force of 490 N (50 kgf, 110 lbf).

    2. Measure the distance between the pedal and dash panel shown in the illustration.

      Pedal reserve distance:
      Model
      Specified Condition
      for LHD
      90.0 mm (3.543 in.)
      for RHD
      83.0 mm (3.268 in.)

      If the distance is not as specified, troubleshoot the brake system.

← ADJUSTMENT (Jun 2011 – Jul 2014)REASSEMBLY (from Jun 2011) →