2014 Hilux · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. INSTALL BRAKE BOOSTER ASSEMBLY
  1. Install a new gasket to the brake booster.

  1. C111300
    Install the booster with the 4 nuts.

    Torque:
    14 N*m{ 145 kgf*cm , 10 ft.*lbf }

  1. Install the push rod clevis.

  1. Apply a light coat of lithium soap base glycol grease to the clevis pin.

  1. C226774E01
    Install the clevis pin and a new clip.

    NOTICE:
    The clip must be installed as shown in the illustration.

  1. Install the return spring.

  1. Install the check valve and grommet to the booster.

  1. Connect the vacuum hose with the clip.

  1. Install the vacuum warning switch and grommet to the booster and connect the vacuum warning switch connector.


2. CHECK AND ADJUST BRAKE BOOSTER PUSH ROD

HINT:
Adjust the booster push rod when the master cylinder is replaced with a new one. Adjustment is not necessary when the master cylinder is reinstalled and the booster is replaced with a new one.

  1. G028332E05
    Set SST on the master cylinder and lower the rod of SST until it just touches the piston.
    SST
    09737-00013  

    HINT:
    SST 09797-00012 can also be used.

  1. Apply chalk to the flat tip of the rod of SST. Turn SST upside down and measure the clearance between the brake booster push rod and SST.

    Standard clearance:
    0 mm (0 in.)

    If there is clearance between the main body of SST and the shell of the brake booster, the push rod is protruding too far. If the chalk does not stick to the tip of the brake booster push rod, the push rod protrusion is insufficient.

  1. F040006E01
    If the clearance is not as specified, adjust the length by holding the rod using SST and turning the tip of the rod using a 7 mm socket driver.
    SST
    09737-00020  

    NOTICE:
    Check the push rod clearance again after adjustment.


3. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
  1. Install the brake master cylinder (Click here).


4. FILL RESERVOIR WITH BRAKE FLUID

Fluid:
Item
Specified Condition
except TSAM Made
SAE J1703 or FMVSS No. 116 DOT 3
for TSAM Made
SAE J1704 or FMVSS No. 116 DOT 4


5. BLEED AIR FROM BRAKE MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. C236931
    Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.

  1. Slowly depress and hold the brake pedal.

  1. C236932
    Block the tube holes with your fingers, and then release the brake pedal.

  1. Remove the your fingers, slowly depress and hold the brake pedal, block the tube holes with your fingers again, and then release the brake pedal. Repeat this step 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake tubes to the brake master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).


6. BLEED AIR FROM BRAKE LINE
  1. Remove the bleeder plug cap.

  1. Connect a vinyl tube to the bleeder plugs.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    for front brake:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }
    for rear brake:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the cap.

  1. C191545
    Bleed air from the brake line for each wheel by repeating the above procedures.


7. BLEED AIR FROM CLUTCH LINE (for Manual Transmission)

C112661E01
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.

  1. Repeat the previous 2 steps until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.

  1. Check that all the air has been bled out of the clutch line.


8. CHECK AND ADJUST BRAKE PEDAL HEIGHT

C194288E01
  1. Check the pedal height.

    Pedal height from dash panel:
    Item
    Specified Condition
    LHD (M/T)
    152.9 to 162.9 mm (6.020 to 6.413 in.)
    LHD (A/T)
    154.1 to 164.1 mm (6.067 to 6.461 in.)
    RHD (M/T)
    156.9 to 166.9 mm (6.177 to 6.571 in.)
    RHD (A/T)
    158.1 to 168.1 mm (6.224 to 6.618 in.)

  1. Adjust the pedal height.

    1. Disconnect the connector from the stop light switch.

    2. Remove the switch.

    3. Loosen the push rod clevis lock nut.

    4. Adjust the pedal height by turning the push rod.

    5. Tighten the lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    6. C111301E04
      Insert the switch into the adjuster until it slightly touches the pedal.

      NOTICE:
      Do not depress the pedal.

    7. C111302E03
      Turn the switch a quarter turn clockwise.

      Torque:
      1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

      NOTICE:
      Do not depress the pedal.

    8. Connect the connector to the switch.

    9. Check the switch clearance.

      Stop light switch clearance:
      1.5 to 2.5 mm (0.0591 to 0.0984 in.)


9. CHECK BRAKE PEDAL FREE PLAY

C111306E02
  1. Stop the engine. Depress the pedal several times until there is no vacuum in the booster. Then release the pedal.

  1. Depress the pedal until resistance is felt.

  1. Check the pedal free play by measuring the distance between the position in the previous step and the pedal's released position.

    Pedal free play:
    1.0 to 6.0 mm (0.0394 to 0.236 in.)

    If the free play is not as specified, check the switch clearance in the next step.
    If the free play is as specified, proceed to the "check brake pedal reserve distance" procedure.

  1. Check the switch clearance.

    Stop light switch clearance:
    1.5 to 2.5 mm (0.0591 to 0.0984 in.)

    If the clearance is not as specified, adjust the clearance and recheck the pedal free play.
    If the clearance is as specified, troubleshoot the brake system and proceed to the "check brake pedal reserve distance" procedure.


10. CHECK BRAKE PEDAL RESERVE DISTANCE

C111339E08
  1. Release the parking brake lever. Start the engine.

  1. Depress the pedal and check the pedal reserve distance.

    1. Depress the pedal with a force of 490 N (50 kgf, 110 lbf).

    2. Measure the distance between the pedal and dash panel shown in the illustration.

      Pedal reserve distance:
      Model
      Specified Condition
      for LHD
      85.0 mm (3.347 in.)
      for RHD
      89.0 mm (3.504 in.)

      If the distance is not as specified, troubleshoot the brake system.


11. CHECK BRAKE FLUID LEVEL IN RESERVOIR

  1. C190487
    Check the fluid level.
    If the brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Fluid:
    Item
    Specified Condition
    except TSAM Made
    SAE J1703 or FMVSS No. 116 DOT 3
    for TSAM Made
    SAE J1704 or FMVSS No. 116 DOT 4


12. CHECK FOR BRAKE FLUID LEAKAGE

13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


14. CHECK SRS WARNING LIGHT
  1. w/ Airbag System:
    Check the SRS warning light (Click here).

← REMOVAL (from Aug 2013)INSTALLATION (Aug 2012 – Jul 2013) →