2014 Hilux · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built from Jun 2011


1. REMOVE TRANSFER INDICATOR SWITCH

C097064E01
  1. Remove the switches and gaskets.

    HINT:
    Indicator switch:
    No. 1
    Indicator switch (neutral position) for A/T
    No. 2
    Indicator switch (L4 position) for A/T or M/T w/ ABS
    No. 3
    Indicator switch (4WD) for A/T and M/T


2. REMOVE TRANSFER GEAR SHIFT HEAD (for Adapter on Type)

G034493E01
  1. Using a pin punch and hammer, remove the 2 slotted pins from the No. 1 and No. 2 gear shift heads.

  1. Remove the No. 1 and No. 2 gear shift heads from the front drive shift fork shaft, and high and low shift fork shaft.


3. REMOVE TRANSFER CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY (for Transfer on Type)

C111616
  1. Remove the 4 bolts and retainer.


4. REMOVE TRANSFER CASE COVER SUB-ASSEMBLY (for Adapter on Type)

C111617
  1. Remove the 4 bolts and case cover.


5. REMOVE BREATHER OIL DEFLECTOR

6. REMOVE TRANSFER BEARING RETAINER SUB-ASSEMBLY

C111638
  1. Remove the 5 bolts and bearing retainer.

    HINT:
    If necessary, tap the bearing retainer with a plastic-faced hammer to remove it.


7. REMOVE TRANSFER COVER OIL SEAL
  1. Using a screwdriver and hammer, tap out the oil seal from the bearing retainer.

    NOTICE:
    Be careful not to damage the oil seal and bearing retainer contact surfaces.


8. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (for Front)
  1. Using a chisel and hammer, loosen the staked part of the lock nut.

  1. F043429E01
    Using SST to hold the companion flange, remove the lock nut.
    SST
    09330-00021  

  1. F043430E01
    Using SST, remove the companion flange.
    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)


9. REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL (for Front)
  1. Using a screwdriver and hammer, tap out the oil seal from the companion flange.

    NOTICE:
    Be careful not to damage the oil seal and companion flange contact surfaces.


10. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (for Rear)
  1. Remove the companion flange (rear) in the same way as the companion flange (front).

    SST
    09330-00021  
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)


11. REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL (for Rear)
  1. Using a screwdriver and hammer, tap out the oil seal from the companion flange.

    NOTICE:
    Be careful not to damage the oil seal and companion flange contact surfaces.


12. REMOVE SPEEDOMETER SENSOR

  1. C243377
    Remove the bolt and speedometer sensor from the transfer.

  1. Remove the O-ring from the speedometer sensor.


13. REMOVE TRANSFER EXTENSION HOUSING SUB-ASSEMBLY
  1. Remove the 5 bolts and extension housing.

    HINT:
    If necessary, tap the extension housing with a plastic-faced hammer to remove it.


14. REMOVE TRANSFER EXTENSION HOUSING TYPE T OIL SEAL
  1. Using a screwdriver and hammer, tap out the oil seal.

    NOTICE:
    Be careful not to damage the oil seal and extension housing contact surfaces.


15. REMOVE TRANSFER OUTPUT SHAFT WASHER

16. REMOVE TRANSFER SPEEDOMETER DRIVE GEAR

17. REMOVE REAR TRANSFER CASE

G039426
  1. Remove the 12 bolts and clamp.

  1. Remove the rear case.

    HINT:
    If necessary, tap the rear case with a plastic-faced hammer to remove it.


18. REMOVE FRONT TRANSFER DRIVE SHIFT FORK SHAFT

C111621E01
  1. Using a hexagon wrench, remove the 2 plugs.

  1. Using a magnetic finger, remove the 2 springs and 2 balls from both holes.

  1. Mount the case rear in a vise.

    NOTICE:
    Place aluminum plates on the vise to prevent damage to the case rear.

  1. C111622
    Using a pin punch and hammer, tap out the 2 slotted pins from the shift shaft stopper and No. 2 gear shift fork.

  1. C111623
    Hold the shift fork shaft in place by hand when removing the pin punch.

  1. C111624E01
    Remove the shift fork shaft, No. 1 gear shift fork, spring and shift shaft stopper.

  1. C111625
    Using a magnetic finger, remove the straight pin.


19. REMOVE TRANSFER HIGH AND LOW SHIFT FORK SHAFT

C111626E01
  1. Remove the shift fork shaft and No. 2 gear shift fork.


20. REMOVE TRANSFER REAR OUTPUT SHAFT, FRONT TRANSFER DRIVE CHAIN AND TRANSFER DRIVEN SPROCKET

C111627
  1. Using a snap ring expander, remove the snap ring.

  1. C111628E01
    Using a plastic-faced hammer, carefully tap the case rear, and remove the output shaft together with the drive chain and driven sprocket.

  1. Remove the output shaft and driven sprocket from the drive chain.


21. REMOVE TRANSFER DRIVEN SPROCKET BEARING

F043523
  1. Using a press, press out the bearing.

    NOTICE:
    Be careful not to drop or damage the driven sprocket.


22. REMOVE TRANSFER INPUT GEAR RADIAL BALL BEARING

F043524E01
  1. Using SST, a press and steel bar, press out the bearing.

    SST
    09555-55010  

    NOTICE:
    Be careful not to damage the driven sprocket.


23. REMOVE NO. 1 TRANSFER CASE PLUG (for Filler)
  1. Remove the filler plug and gasket.


24. REMOVE NO. 1 TRANSFER CASE PLUG (for Drain)
  1. Remove the drain plug and gasket.


25. REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY

F043446
  1. Remove the 3 bolts and oil separator.


26. REMOVE TRANSFER CASE MAGNET

27. REMOVE TRANSFER OIL PUMP BODY SUB-ASSEMBLY

F043447E01
  1. Remove the 3 bolts and oil pump body.


28. REMOVE TRANSFER OIL PUMP BODY O-RING

F043462
  1. Using a screwdriver, remove the O-ring from the oil pump body.

    NOTICE:
    Be careful not to damage the oil pump body.


29. REMOVE TRANSFER OIL PUMP GEAR

F043448
  1. Remove the nut and oil pump gear.


30. REMOVE FRONT TRANSFER DRIVE CLUTCH SYNCHRONIZER RING (for Manual Transmission)

C111629
  1. Remove the synchronizer ring from the planetary gear.


31. REMOVE TRANSFER LOW PLANETARY GEAR ASSEMBLY WITH TRANSFER INPUT SHAFT

F043449
  1. Using a snap ring expander, remove the snap ring.

  1. C111630
    Remove the low planetary gear with the input shaft.


32. REMOVE TRANSFER CASE PLUG

F043455E01

33. REMOVE COMPRESSION SPRING

34. REMOVE PIN

35. REMOVE TRANSFER LOW PLANETARY RING GEAR

F043456
  1. Using a screwdriver, pry out the snap ring.

    NOTICE:
    Be careful not to damage the case front.

  1. Remove the ring gear from the case front.


36. REMOVE TRANSFER CASE OIL SEAL
  1. Using a screwdriver and hammer, tap out the oil seal (No. 1).

  1. Using a screwdriver and hammer, tap out the oil seal (No. 2).

    NOTICE:
    Be careful not to damage the oil seal and case front contact surfaces.


37. REMOVE TRANSFER LOW PLANETARY GEAR SPLINE PIECE

C111631
  1. Using a screwdriver, pry out the snap ring.

    NOTICE:
    Be careful not to damage the low planetary gear.

  1. C111632
    Remove the spline piece.


38. REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING

C111633

39. REMOVE TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING

C111634
  1. Using a snap ring expander, remove the snap ring.


40. REMOVE TRANSFER INPUT GEAR STOPPER

G034494E01

41. REMOVE TRANSFER INPUT GEAR STOPPER BALL

42. REMOVE MANUAL TRANSFER PLANETARY CARRIER WASHER

43. REMOVE TRANSFER INPUT SHAFT

C111635E01

44. REMOVE NO. 1 TRANSFER THRUST BEARING RACE

45. REMOVE TRANSFER LOW PLANETARY GEAR BEARING

46. REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING

C111636
  1. Remove the 2 seal rings.


47. REMOVE TRANSFER INPUT SHAFT BEARING
  1. Using a snap ring expander, remove the snap ring.

  1. F043467E01
    Using SST and a press, press out the bearing.
    SST
    09554-30011  
    09555-55010  

    NOTICE:
    Be careful not to drop or damage the low planetary gear.


48. REMOVE TRANSFER LOW PLANETARY GEAR BEARING

F043526E01
  1. Using SST, remove the bearing.

    SST
    09612-65014   (09612-01030, 09612-01050)

    NOTICE:
    Hang SST securely between the bearing and low planetary gear.


49. REMOVE TRANSFER CLUTCH HUB (for Manual Transmission)

C111645
  1. Using a snap ring expander, remove the snap ring.

  1. Remove the high and low clutch sleeve, 3 shifting keys and 2 shifting key springs.

  1. Using a press, press out the clutch hub.

    NOTICE:
    Be careful not to drop or damage the clutch hub.


50. REMOVE TRANSFER CLUTCH HUB (for Automatic Transmission)
  1. Using a snap ring expander, remove the snap ring.

  1. Remove the high and low clutch sleeve.

  1. Using a press, press out the clutch hub.

    NOTICE:
    Be careful not to drop or damage the clutch hub.


51. REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY (for A.D.D. Manual Shift Type)

C111646E01
  1. Using SST and a press, press out the bearing.

    SST
    09555-55010  

    NOTICE:
    Be careful not to drop or damage the output shaft.

  1. C111647E01
    Remove the spacer and ball.

  1. Remove the drive sprocket with front drive clutch sleeve.

  1. Remove the needle roller bearing.

  1. Remove the front drive synchronizer ring.

  1. Remove the front drive sleeve, 3 shifting keys and 2 shifting key springs from the drive sprocket.


52. REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY (for Normal Shift Type)

C111646E01
  1. Using SST and a press, press out the bearing.

    SST
    09555-55010  

    NOTICE:
    Be careful not to drop or damage the output shaft.

  1. C111652E01
    Remove the spacer and ball.

  1. Remove the drive sprocket with front drive clutch sleeve.

  1. Remove the needle roller bearing.

← REMOVAL (from Aug 2013)INSPECTION (from Jun 2011) →