ON-VEHICLE INSPECTION
Inspection · Vehicles built from Jun 2011
| DRAIN DIFFERENTIAL OIL |
for front differential:
Stop the vehicle on a level surface.
Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, remove the differential filler plug and gasket.

- SST
- 09961-00950
Text in Illustration *1
10 mm Straight Hexagon Wrench
*2
10 mm Union Nut Wrench
*3
Socket Adaptor
Remove the drain plug and gasket, and drain the oil.
Install a new gasket and the drain plug.
- Torque:
- 65 N*m{ 660 kgf*cm , 48 ft.*lbf }
for rear differential:
Stop the vehicle on a level surface.
Remove the differential filler plug and gasket.
Remove the drain plug and gasket, and drain the oil.
Install a new gasket and the drain plug.
- Torque:
- 49 N*m{ 500 kgf*cm , 36 ft.*lbf }
| ADD DIFFERENTIAL OIL |
Add differential oil so that the oil level is within 5 mm (0 to 0.196 in.) from the bottom lip of the differential filler plug hole.

Text in Illustration *a
0 to 5 mm (0 to 0.196 in.)
- NOTICE:
- After changing the oil seal, drive the vehicle and then check the oil level again.
- Too much or too little oil will lead to differential problems.
- After changing the oil seal, drive the vehicle and then check the oil level again.
- HINT:
- If necessary, fill the differential carrier assembly with hypoid gear oil.
- Recommended viscosity:
Item
Temperature
Viscosity
Front differential (w/ A.D.D.)
SAE 75W-90
Front differential (w/o A.D.D.)
Rear differential
Above -18°C (0°F)
SAE 90
Below -18°C (0°F)
SAE 80W-90 or SAE 80W
- Differential oil type:
Item
Oil type
Front differential
Rear differential
Hypoid gear oil API GL-5 or equivalent
Rear differential (for LSD)
Hypoid gear oil LSD API GL-5 or equivalent
- Standard front differential oil capacity:
Item
Capacity
w/o A.D.D.
1.40 to 1.50 liters (1.48 to 1.58 US qts., 1.23 to 1.32 Imp. qts.)
w/ A.D.D.
1.60 to 1.70 liters (1.69 to 1.79 US qts., 1.41 to 1.49 Imp. qts.)
- TMT made Standard rear differential oil capacity:
Item
Capacity
2WD and w/ LSD
3.15 to 3.25 liters (3.33 to 3.43 US qts., 2.78 to 2.86 Imp. qts.)
4WD and w/o LSD
3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)
- TSAM made :
Item
Capacity
2WD and made for DANA
2.30 to 2.40 liters (2.43 to 2.54 US qts., 2.02 to 2.11 Imp. qts.)
4WD, Pre-runner and made for DANA
(w/o LSD, A.D.D.)
2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)
w/ LSD for 2WD
3.15 to 3.25 liters (3.33 to 3.43 US qts., 2.78 to 2.86 Imp. qts.)
w/ LSD for 4WD
3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)
w/ Differential lock
2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.60 Imp. qts.)
Check for oil leakage when the oil level is low.
for front differential:
Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, install a new gasket and the differential filler plug.

- SST
- 09961-00950
Text in Illustration *1
10 mm Straight Hexagon Wrench
*2
10 mm Union Nut Wrench
*3
Socket Adaptor
- Torque:
- 39 N*m{ 400 kgf*cm , 29 ft.*lbf }
- NOTICE:
- Make sure all the tools are connected in a straight line.
- Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.
- Formula:
- T' = T x L3 / (L1 + L2 + L3)
- T' = Spec. value of torque wrench
- T = Value of specified tightening torque
- L1 = Length of union nut wrench
- L2 = Length of SST
- L3 = Length of torque wrench
- Make sure all the tools are connected in a straight line.
for rear differential:
Install a new gasket and the differential filler plug.
- Torque:
- 49 N*m{ 500 kgf*cm , 36 ft.*lbf }
