2014 Hilux · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built from Jun 2011


1. FIX REAR DIFFERENTIAL CARRIER ASSEMBLY

C121133

2. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR

  1. F001237E03
    Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Maximum runout:
    Runout
    Maximum
    Vertical runout
    0.10 mm (0.0039 in.)
    Lateral runout
    0.10 mm (0.0039 in.)

    1. If the runout is greater than the maximum, replace the companion flange.


3. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

  1. C121134
    Using a dial indicator, measure the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.0028 in.)

    1. If the runout is greater than the maximum, replace the ring gear with a new one.


4. INSPECT DIFFERENTIAL RING GEAR BACKLASH

  1. C121135
    Using a dial indicator, measure the backlash of the ring gear.

    Standard backlash:
    0.13 to 0.18 mm (0.0051 to 0.0071 in.)

    1. If the backlash is not within the specification, adjust the side bearing preload or repair as necessary.

      HINT:
      Perform the measurements at 3 or more positions around the side bearing preload.


5. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

  1. C003092E01
    Using a torque wrench, measure the preload of backlash between the drive pinion and ring gear.

    Standard drive pinion preload (at start of torque):
    0.56 to 0.85 N*m (6 to 9 kgf*cm, 4.9 to 7.5 in.*lbf)

    1. If necessary, disassemble and inspect the differential.


6. INSPECT TOTAL PRELOAD

  1. C003092E01
    Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

  1. Using a torque wrench, measure the total preload.

    HINT:
    A bolt without a torque specification is shown in the service data (Click here).

    1. If necessary, disassemble and inspect the differential.


7. REMOVE REAR DRIVE PINION NUT

  1. F044346E01
    Using SST and a hammer, loosen the staked part of the nut.
    SST
    09930-00010   (09931-00010, 09931-00020)

  1. SA02349E03
    Using SST to hold the companion flange in place, remove the nut.
    SST
    09330-00021   (09330-00030)


8. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

  1. B087869E01
    Using SST, remove the companion flange.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.


9. REMOVE REAR DIFFERENTIAL DUST DEFLECTOR

  1. F040564E02
    Using SST and a press, press out the dust deflector.
    SST
    09950-60010   (09951-00380)
    09950-70010   (09951-07150)
    09950-00020  

    NOTICE:
    Do not drop the companion flange.


10. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

  1. SA02348E02
    Using SST, remove the oil seal from the differential carrier.
    SST
    09308-10010  


11. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

12. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. Z000641E01
    Using SST, remove the roller bearing (inner) from the drive pinion.
    SST
    09556-22010  


13. REMOVE DIFFERENTIAL CASE ASSEMBLY

  1. C121136E01
    Place matchmarks on the bearing cap and differential carrier.

  1. Remove the 4 bolts and 2 differential bearing caps.

  1. Remove the 2 side shims.

  1. C028220E01
    Remove the rear differential case assembly from the differential carrier.

    HINT:
    Tag the 2 case bearing outer races to show the location for reassembly.


14. REMOVE DIFFERENTIAL DRIVE PINION
  1. Remove the drive pinion and bearing spacer from the differential carrier.


15. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

  1. R010668E01
    Using SST and a press, press out the roller bearing (inner) from the drive pinion.
    SST
    09950-00020  

    NOTICE:
    Do not drop the drive pinion.

    HINT:
    If the drive pinion or ring gear is damaged, replace them as a set.


16. REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

17. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. F044358E01
    Using SST, remove the roller bearing (outer) from the carrier.
    SST
    09308-00010  

  1. Using a brass bar and hammer, tap out the oil storage ring from the carrier.

    HINT:
    If the bearing is damaged during removal, replace it.


18. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

  1. C091047E01
    Using a brass bar and hammer, tap out the rear tapered roller bearing (outer) from the carrier.

    HINT:
    If the bearing is damaged during removal, replace it.


19. REMOVE DIFFERENTIAL RING GEAR

  1. C121137E01
    Place matchmarks on the ring gear and differential case.

  1. Remove the 10 ring gear set bolts.

  1. C014054E02
    Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


20. INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT
  1. Install the rear differential case bearing to the differential case.

  1. Install the differential case to the differential carrier.

  1. Install the 2 bearing caps to the differential carrier with the 4 bolts.

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

  1. C121138
    Using a dial indicator, measure the differential case runout.

    Maximum runout:
    0.07 mm (0.0028 in.)

  1. Remove the differential case.

  1. Remove the rear differential case bearing.


21. REMOVE REAR DIFFERENTIAL CASE BEARING

  1. F040345E02
    Using SST, remove the 2 bearings from the differential case.
    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00360)

    HINT:
    Do not remove the case bearing when not replacing the differential case.


22. INSPECT DIFFERENTIAL PINION AND SIDE GEAR
  1. Check that the differential pinion and differential side gear are not worn.

    1. If the differential pinion or differential side gear is not worn, replace the differential.


23. INSPECT DIFFERENTIAL CASE

  1. F014547E02
    Measure the side gear backlash.

    1. Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case.

      Standard backlash:
      0.05 to 0.20 mm (0.0020 to 0.008 in.)

      1. If the backlash is not within the specified range, replace the differential case with a new one.

← REMOVAL (from Jun 2011)REASSEMBLY (from Jun 2011) →