2014 Hilux · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE NO.1 ENGINE UNDER COVER

3. REMOVE NO.2 ENGINE UNDER COVER

4. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the front pipe from the outlet pipe and remove the gasket.

  1. Remove the front pipe from the pipe support.


5. REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
  1. Remove the propeller shaft with center bearing assembly (Click here).


6. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }


7. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

G039346E01
  1. Remove the oil dipstick.

  1. Remove the 2 bolts and oil filler tube.

  1. Remove the O-ring from the oil filler tube.


8. DISCONNECT OIL COOLER TUBE

G034850E02
  1. Using a union nut wrench, disconnect the inlet tube and outlet tube.

  1. G034255E01
    Remove the 3 bolts and 3 clamps.


9. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

G034515E01
  1. Remove the nut and disconnect the control cable.

  1. Remove the clip and disconnect the control cable.


10. REMOVE TRANSMISSION CONTROL CABLE BRACKET

G034516E01
  1. Remove the 2 bolts and control cable bracket from the transmission.


11. REMOVE STARTER ASSEMBLY
  1. Remove the starter (Click here).


12. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

G034520E01
  1. Support the transmission with a transmission jack.


13. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

G034517E01
  1. *1: Remove the 4 set bolts of the No. 1 engine mounting insulator rear.

  1. *2: Remove the 4 nuts, 4 bolts and frame crossmember.


14. REMOVE NO. 1 ENGINE MOUNTING INSULATOR REAR

C238609
  1. Remove the 4 bolts, ground cable and engine mounting insulator.


15. DISCONNECT CONNECTOR

G034521E01
  1. Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.

  1. Disconnect the connectors.

    1. Disconnect the temperature sensor connector.

    2. Disconnect the park/neutral position switch connector.

    3. Disconnect the 3 speed sensor connectors.

    4. Disconnect the transmission wire connector.


16. DISCONNECT WIRE HARNESS

17. REMOVE STIFFENER PLATE

G034607E03
  1. Remove the 4 bolts and stiffener plate RH (with clamp tube).

  1. Remove the 4 bolts and stiffener plate LH.

  1. Remove the No. 4 cylinder block insulator.

  1. Remove the No. 2 end plate.


18. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

G034258E01
  1. Turn the crankshaft to gain access to each bolt.

  1. Hold the crankshaft pulley bolt with a wrench, and remove the 6 torque converter clutch mounting bolts.

  1. G034259E01
    Remove the 5 bolts.

  1. Separate the transmission from the engine.


19. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY
← COMPONENTS (from Aug 2012)REMOVAL (Aug 2012 – Jul 2013) →