2014 Hilux · Service Manual BRAKE

REASSEMBLY

Removal / installation · Vehicles built Jun 2011 – Jul 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. INSTALL REAR WHEEL BRAKE CYLINDER CUP

C115338E02
  1. Apply lithium soap base glycol grease to 2 new cups and 2 pistons.

  1. Install the 2 cups to each piston.

  1. Install the compression spring and 2 pistons to the cylinder.

  1. Install 2 new cylinder dust boots to the cylinder.


2. TEMPORARILY TIGHTEN REAR BRAKE DRUM BLEEDER PLUG
  1. Install the bleeder plug to the cylinder.

    HINT:
    The bleeder plug will be tightened to a torque specification in the "bleed air from brake line" procedures.

  1. Install the cap.


3. INSTALL REAR WHEEL BRAKE CYLINDER ASSEMBLY LH

  1. C111485
    Install the cylinder with the 2 bolts.

    Torque:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }

  1. Using a union nut wrench, connect the brake line.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).


4. APPLY HIGH TEMPERATURE GREASE

  1. C111487E03
    Apply high temperature grease to the surface of the backing plate where the shoe will be attached.

  1. Apply high temperature grease to the anchor block plate and cable setting area.


5. INSTALL REAR BRAKE PARKING BRAKE SHOE LEVER SUB-ASSEMBLY

C111488
  1. Using needle-nose pliers, install the lever with a new C-washer.


6. INSTALL REAR BRAKE AUTOMATIC ADJUST LEVER LH

C111489
  1. Using needle-nose pliers, install the lever with the E-ring.


7. INSTALL REAR BRAKE SHOE

C111480
  1. Using needle-nose pliers, connect the No. 3 parking brake cable to the parking brake shoe lever.

  1. Using needle-nose pliers, install the adjust lever tension spring to the automatic adjust lever and rear brake shoe.

  1. C111398E01
    Using SST, install the shoe, pin, shoe hold down spring and shoe hold down spring cup.
    SST
    09718-00010  


8. INSTALL PARKING BRAKE SHOE STRUT SET LH

  1. C115331E02
    Disassemble the strut set. Apply high temperature grease to the areas indicated by the arrows in the illustration. Then reassemble the strut set.

  1. Install the shoe return spring to the strut set.

  1. C122023E01
    Install the strut set as shown in the illustration.


9. INSTALL FRONT BRAKE SHOE

  1. C111397E01
    Connect the shoe tension spring to the front brake shoe and rear brake shoe.

  1. Using SST, install the shoe, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00010  


10. CONNECT REAR BRAKE SHOE RETURN SPRING

  1. C111396E01
    Using SST, connect the return spring to the front brake shoe and rear brake shoe.
    SST
    09703-30011  

    NOTICE:
    Be careful not to damage the wheel cylinder boot.


11. CHECK REAR BRAKE DRUM INSTALLATION

  1. Check that each part is installed properly.

    C115333E01

  1. C111493
    Measure the inside diameter of the drum and diameter of the brake shoes. Check that the difference between the diameters is the correct shoe clearance.

    Standard shoe clearance:
    0.5 mm (0.0197 in.)

    NOTICE:
    There should be no oil or grease on the contact surfaces of the shoe lining and drum.

← INSPECTION (from Jun 2011)REASSEMBLY (from Aug 2013) →