2014 Hilux · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Jun 2011


1. INSTALL OUTPUT SHAFT ASSEMBLY

D033548E01
  1. Install the output shaft into the intermediate plate by pushing on the output shaft and tapping on the intermediate plate with a plastic-faced hammer.

  1. D033546E01
    Using a snap ring expander, install the snap ring to the center bearing.

    HINT:
    Be sure the shaft snap ring is flush with the intermediate plate surface.


2. INSTALL COUNTER GEAR ASSEMBLY

D033550E01
  1. Coat the input shaft and No. 2 synchronizer ring with gear oil.

  1. Temporarily install the counter gear, input shaft and a new center bearing to the intermediate plate.

    NOTICE:
    Install the bearing (with snap ring) to the counter gear's rear side.

  1. D029191E01
    Using a plastic-faced hammer, install the center bearing to the intermediate plate by tapping the outer race to the counter gear center bearing.

    HINT:
    Hold the front side of the counter gear by hand.

  1. D029185E01
    Using a snap ring expander, install the snap ring to the counter shaft center bearing.


3. INSTALL OUTPUT SHAFT REAR BEARING RETAINER

D033544E01
  1. Using a T40 "torx" socket, install the rear bearing retainer to the intermediate plate with the 4 screws.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }


4. INSTALL REVERSE IDLER GEAR

D033543E01
  1. Install the idler gear shaft and idler gear to the intermediate plate.

  1. D033542E01
    Install the idler gear shaft stopper to the intermediate plate with the bolt.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }


5. INSTALL REVERSE SHIFT ARM

D033431E01
  1. Install a new E-ring and the shift fork to the shift arm.


6. INSTALL REVERSE SHIFT ARM BRACKET

D033529E01
  1. Install the arm bracket with the shift arm to the intermediate plate.

  1. Install the 2 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }


7. INSTALL 5TH GEAR THRUST WASHER LOCK BALL

D033551E01
  1. Install the lock ball.


8. INSTALL 5TH GEAR THRUST WASHER

D033540E01

9. INSTALL COUNTER SHAFT 5TH GEAR ASSEMBLY

D033552E01
  1. Install the 5th gear bearing to the 5th gear.

  1. Install the 5th gear to the counter gear.

  1. D033553E01
    Temporarily install the No. 3 synchronizer ring on the No. 5 gear spline piece.

  1. D033554E01
    Dismount the intermediate plate from the vise.

  1. Stand the transmission as shown in the illustration.

  1. D033555E01
    Using a press and 22 mm socket wrench, press in the No. 5 gear spline piece with the No. 3 synchronizer ring slots aligned with the shifting keys.

  1. Mount the intermediate plate to the vise.

  1. D033563E01
    Select a snap ring that will allow minimal axial play.

    Standard clearance:
    0.10 mm (0.0039 in.) or less

    Standard counter gear rear shaft snap ring thickness:
    Mark
    Thickness
    A
    2.80 to 2.85 mm (0.110 to 0.112 in.)
    B
    2.85 to 2.90 mm (0.112 to 0.114 in.)
    C
    2.90 to 2.95 mm (0.114 to 0.116 in.)
    D
    2.95 to 3.00 mm (0.116 to 0.118 in.)
    E
    3.00 to 3.05 mm (0.118 to 0.120 in.)
    F
    3.05 to 3.10 mm (0.120 to 0.122 in.)
    G
    3.10 to 3.15 mm (0.122 to 0.124 in.)

  1. D033556E01
    Using a brass bar and hammer, tap in the snap ring to the counter gear.


10. INSPECT COUNTER SHAFT 5TH GEAR THRUST CLEARANCE

C086399E01
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.100 to 0.300 mm (0.0039 to 0.0117 in.)

    Maximum clearance:
    0.300 mm (0.0117 in.)


11. INSTALL NO. 2 SHIFT FORK SHAFT

D033557E03
  1. Install the No. 2 shift fork shaft through the No. 2 gear shift fork, No. 1 gear shift fork and intermediate plate.

  1. D029199E01
    Using a brass bar and hammer, tap in the shaft snap ring to the No. 2 shift fork shaft.

  1. D029173E01
    Install the bolt to the No. 2 gear shift fork.

    Torque:
    20 N*m{ 204 kgf*cm , 14 ft.*lbf }


12. INSTALL NO. 2 SHIFT INTERLOCK PIN

D029200E01
  1. Coat the No. 2 shift interlock pin with MP grease, and install it into the No. 1 gear shift fork shaft.


13. INSTALL NO. 1 SHIFT FORK SHAFT

D029201E01
  1. Coat the No. 1 interlock pin with MP grease.

  1. Using a magnetic finger, install the No. 1 interlock pin to the intermediate plate.

  1. Install the No. 1 gear shift fork shaft through the No. 2 gear shift fork and intermediate plate.

  1. D029170E01
    Install the bolt to the No. 1 shift fork.

    Torque:
    20 N*m{ 204 kgf*cm , 14 ft.*lbf }

  1. D029202E01
    Using pliers, install the snap ring to the No. 1 gear shift fork shaft.


14. INSTALL NO. 3 HEAD GEAR SHIFT

D033530E01
  1. Install the No. 3 head gear shift to the No. 3 shift fork shaft.

  1. Using a 5 mm pin punch and hammer, tap in the slotted spring pin to the No. 3 shift fork shaft.


15. INSTALL NO. 2 SHIFT INTERLOCK PIN

D033613E01
  1. Coat the No. 2 interlock pin with MP grease, and install it into the No. 3 shift fork shaft.


16. INSTALL NO. 3 SHIFT FORK SHAFT

B087770E01
  1. Coat the shift interlock pin with MP grease.

  1. Using a magnetic finger, install the No. 3 shift interlock pin to the intermediate plate.

  1. Install the No. 3 shift fork shaft through the reverse shift fork and the intermediate plate.

  1. Coat the shift detent ball with MP grease.

  1. Install the shift detent ball and the shift detent ball low side compression spring to the reverse shift fork.

  1. Install the No. 3 shift fork shaft through the reverse shift arm.


17. INSTALL NO. 5 SHIFT FORK SHAFT

D029161E03
  1. Install the reverse shift head and No. 5 shift fork shaft.

  1. D029160E01
    Using a 5 mm pin punch and hammer, tap in the slotted spring pin to the reverse shift head.


18. INSTALL NO. 4 SHIFT FORK SHAFT

B087771E01
  1. Coat the ball pin shift interlocks with MP grease.

  1. Using a magnetic finger, install the ball pin shift interlocks to the intermediate plate.

  1. Install the No. 4 shift fork shaft through the reverse shift fork, intermediate plate and reverse shift head.

  1. D033526E01
    Using a brass bar and hammer, tap in the shift fork shaft snap ring and 2 reverse shift head rings.

  1. D029157E01
    Install the bolt to the No. 3 gear shift fork.

    Torque:
    20 N*m{ 204 kgf*cm , 14 ft.*lbf }


19. INSTALL NO. 2 SHIFT DETENT BALL

D029208E01
  1. Coat the No. 2 detent ball with MP grease.

  1. Install the No. 2 detent ball and compression spring to the intermediate plate.

  1. D029155E01
    Coat the spring seat with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Using a T40 "torx" socket, install the spring seat to the intermediate plate.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }


20. INSTALL SHIFT DETENT BALL

D033532E01
  1. Coat the 3 shift detent balls with MP grease, and install them and the 3 compression springs to the intermediate plate.

  1. D033558E01
    Coat the 3 spring seats with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Using a T40 "torx" socket, install the 3 spring seats to the intermediate plate.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }


21. INSTALL MANUAL TRANSMISSION CASE

C086438E01
  1. Apply seal packing to the transmission case as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. C109840
    Stand the intermediate plate as shown in the illustration.

  1. Using a plastic-faced hammer, install the transmission case to the intermediate plate as shown in the illustration.


22. INSTALL NO. 1 COUNTER GEAR FRONT BEARING SNAP RING

D029150E01
  1. Using a snap ring expander, install the snap ring to the front bearing.


23. INSTALL FRONT BEARING SHAFT SNAP RING

D029149E01
  1. Using a snap ring expander, install the snap ring to the input shaft front bearing.


24. INSTALL TRANSMISSION FRONT BEARING RETAINER OIL SEAL

C086440E01
  1. Using SST, press in a new oil seal to the front bearing retainer.

    SST
    09950-60010   (09952-06010, 09951-00440)

    Standard depth:
    12.5 to 13.5 m (0.492 to 0.531 in.)


25. CHECK BEARING RETAINER FRONT

C112666E01
  1. Check that "FIPG" is imprinted on the bearing retainer front.


26. INSTALL BEARING RETAINER FRONT

D033614E02
  1. w/o Gasket:
    Apply seal packing to the bearing retainer front as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. w/ Gasket:
    Install a new gasket and the bearing retainer front to the transmission case.

  1. D029148E01
    w/o Gasket:
    Install the bearing retainer front to the transmission case.

  1. Apply adhesive to the bolt threads.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the 8 bolts.

    Torque:
    17 N*m{ 175 kgf*cm , 12 ft.*lbf }


27. INSTALL EXTENSION HOUSING OIL SEAL

G034230E03
  1. Using SST, tap in a new oil seal to the extension housing.

    SST
    09223-00010  

  1. Lightly apply MP grease to the tip of the oil seal.

    Standard depth:
    0 +-0.5 mm (0 +-0.0196 in.)

    NOTICE:
    Be careful no to damage the lip of the oil seal.


28. INSTALL REVERSE RESTRICT PIN

D029146E01
  1. Install the restrict pin to the extension housing.

  1. D029145E01
    Using a 5 mm pin punch and hammer, tap in the slotted spring pin to the extension housing.

  1. D029144E01
    Using a T40 "torx" socket, install the plug to the extension housing.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }


29. INSTALL OIL RECEIVER
  1. Install the oil receiver with the bolt.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }


30. INSTALL OIL RECEIVER PIPE

D029142E01
  1. Install the oil receiver pipe to the extension housing.


31. INSTALL TRANSMISSION MAGNET

D029141E01
  1. Install the magnet to the extension housing.


32. INSTALL EXTENSION HOUSING

C086443E01
  1. Apply seal packing to the extension housing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. G034242E01
    Install the shift and select lever to the extension housing.

  1. Connect the shift and select lever to the shift fork shaft and insert the shift lever housing.

  1. Align the No. 5 shift fork shaft to the extension housing installation hole and slide it into the extension housing.

  1. G034240E01
    Install the extension housing to the manual transmission case with the 8 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. G034241E01
    Install the bolt to the shift lever housing.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }


33. INSTALL SHIFT DETENT BALL

D029211E01
  1. Coat the shift detent ball with MP grease, and install it and the compression spring to the extension housing.

  1. D029138E01
    Using a T40 "torx" socket, install the spring seat to the extension housing.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }


34. INSTALL SPEEDOMETER DRIVEN GEAR
  1. Install a new O-ring to the driven gear.

  1. Install the driven gear with the bolt.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }


35. INSTALL CONTROL SHIFT LEVER RETAINER

G034238E01
  1. Install the oil deflector and shift lever retainer to the extension housing with the 4 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }


36. INSTALL RESTRICT PIN

G034239E01
  1. Install the 2 restrict pins to the extension housing.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }


37. INSTALL CLUTCH HOUSING

D029131E01
  1. Install the clutch housing.

  1. Apply adhesive to the bolt threads.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the 9 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


38. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

D029130E01
  1. Using SST, install the back-up light switch to the transmission case.

    SST
    09817-16011  

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


39. INSTALL CLUTCH RELEASE FORK BOOT

D029348E01
  1. Install the release fork boot to the clutch housing.


40. INSTALL RELEASE FORK SUPPORT

C086353E01
  1. Install the release fork support to the clutch housing.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


41. INSTALL CLUTCH RELEASE BEARING ASSEMBLY

D029898E01
  1. Coat the release bearing with Multemp 8158 Grease or equivalent, and install it to the release fork.

    Grease:
    Multemp 8158 Grease or equivalent


42. INSTALL CLUTCH RELEASE FORK

C086352E01
  1. Install the release fork to the input shaft.

  1. Apply molybdenum disulphide lithium base grease to the input shaft spline.


43. INSTALL DRAIN PLUG

D029129E01
  1. Install a new gasket and the drain plug to the transmission case.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


44. INSTALL FILLER PLUG

D029128E01
  1. Install a new gasket and the filler plug to the transmission case.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

← REMOVAL (from Jun 2011)COMPONENTS (from Jun 2011) →