2014 Hilux · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Jun 2011


1. INSTALL NO. 2 TRANSMISSION CLUTCH HUB

C086574E01
  1. Coat the hub sleeve with gear oil, and install it to the clutch hub.

    NOTICE:
    Be sure to set the hub sleeve to the clutch hub in the correct direction.

  1. C086575E01
    Install the 3 synchromesh shifting keys to the clutch hub with the 2 synchromesh shifting key springs.

    HINT:
    Do not set both openings of the shifting key springs in the same position.


2. INSTALL 3RD GEAR NEEDLE ROLLER BEARING

C086556E01
  1. Coat the needle roller bearing with gear oil, and install it to the output shaft.


3. INSTALL 3RD GEAR

C086577E01
  1. Coat the 3rd gear with gear oil, and install it to the output shaft.


4. INSTALL NO. 2 SYNCHRONIZER RING

C086576E01
  1. Coat the synchronizer ring with gear oil, and install it to the 3rd gear.


5. INSTALL NO. 2 TRANSMISSION CLUTCH HUB

D029216E01
  1. Using SST and a press, press in the No. 2 clutch hub to the output shaft.

    SST
    09316-60011   (09316-00021)

  1. C086579E01
    Select a clutch hub shaft snap ring that will allow minimal axial play.

    Standard clearance:
    0.10 mm (0.039 in.) or less

    Standard clutch hub shaft snap ring thickness:
    Mark
    Thickness
    C-1
    1.75 to 1.80 mm (0.0689 to 0.0709 in.)
    D
    1.80 to 1.85 mm (0.0709 to 0.0728 in.)
    D-1
    1.85 to 1.90 mm (0.0728 to 0.0748 in.)
    E
    1.90 to 1.95 mm (0.0748 to 0.0768 in.)
    E-1
    1.95 to 2.00 mm (0.0768 to 0.0787 in.)
    F
    2.00 to 2.05 mm (0.0787 to 0.0807 in.)
    F-1
    2.05 to 2.10 mm (0.0807 to 0.0827 in.)

  1. C086553E01
    Using a snap ring expander, install the snap ring.


6. INSPECT 3RD GEAR THRUST CLEARANCE

C086580E01
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.25 mm (0.0039 to 0.0098in.)


7. INSTALL NO. 1 TRANSMISSION CLUTCH HUB

C086581E01
  1. Coat the reverse gear with gear oil, and install it to the clutch hub.

    NOTICE:
    Be sure to set the reverse gear to the clutch hub in the correct direction.

  1. C086575E01
    Install 3 synchromesh shifting keys to the clutch hub with the 2 synchromesh shifting key springs.

    HINT:
    Do not set both openings of the shifting key springs in the same position.


8. INSTALL 2ND GEAR NEEDLE ROLLER BEARING

C086582E01
  1. Coat the needle roller bearing with gear oil, and install it to the output shaft.


9. INSTALL 2ND GEAR

C086583E01
  1. Coat the 2nd gear with gear oil, and install it to the output shaft.


10. INSTALL NO. 1 SYNCHRONIZER RING (for 2nd Gear)

C086584E01
  1. Coat the No. 1 synchronizer ring with gear oil, and install it to the 2nd gear.


11. INSTALL NO. 1 TRANSMISSION CLUTCH HUB

C086585E01
  1. Using SST and a press, press in the clutch hub to the output shaft.

    SST
    09316-60011  


12. INSPECT 2ND GEAR THRUST CLEARANCE

C237935E02
  1. Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.250 mm (0.0039 to 0.0098 in.)


13. INSTALL NO. 1 SYNCHRONIZER RING (for 1st Gear)

C086587E01
  1. Coat the synchronizer ring with gear oil, and install it to the No. 1 clutch hub.


14. INSTALL 1ST GEAR BEARING INNER RACE LOCK BALL

C086588E01
  1. Coat the lock ball with gear oil, and install it to the output shaft.


15. INSTALL 1ST GEAR BEARING INNER RACE

C086589E01
  1. Coat the needle roller bearing with gear oil.

  1. Install the inner race and the needle roller bearing to the 1st gear.


16. INSTALL 1ST GEAR

C086590E01
  1. Coat the 1st gear with gear oil, and install it to the output shaft.


17. INSTALL OUTPUT SHAFT CENTER BEARING

C086591E01
  1. Using SST and a press, press in the center bearing to the output shaft.

    SST
    09316-60011   (09316-00021)


18. INSPECT 1ST GEAR THRUST CLEARANCE

C237934E02
  1. Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.25 mm (0.0039 to 0.0078 in.)


19. INSTALL 5TH GEAR

C086593E01
  1. Using SST and a press, press in the 5th gear to the output shaft.

    SST
    09316-60011   (09316-00021)

  1. D033312E01
    Select a snap ring that will allow minimal axial play.

    Standard clearance:
    0.10 mm (0.039 in.) or less

    Standard output shaft bearing shaft snap ring:
    Mark
    Thickness
    A
    2.67 to 2.72 mm (0.1051 to 0.1071 in.)
    B
    2.73 to 2.78 mm (0.1075 to 0.1094 in.)
    C
    2.79 to 2.84 mm (0.1098 to 0.1118 in.)
    D
    2.85 to 2.90 mm (0.1122 to 0.1141 in.)
    E
    2.91 to 2.96 mm (0.1146 to 0.1165 in.)
    F
    2.97 to 3.02 mm (0.1169 to 0.1189 in.)
    G
    3.03 to 3.08 mm (0.1193 to 0.1213 in.)
    H
    3.09 to 3.14 mm (0.1217 to 0.1236 in.)
    J
    3.15 to 3.20 mm (0.1240 to 0.1260 in.)
    K
    3.21 to 3.26 mm (0.1264 to 0.1283 in.)
    L
    3.27 to 3.32 mm (0.1287 to 0.1307 in.)

  1. D033313E01
    Using a screwdriver and hammer, tap in the snap ring.


20. INSTALL SPEEDOMETER DRIVE GEAR

G034243E01
  1. Using a snap ring expander, install the snap ring.

  1. Install the ball.

  1. Install the drive gear.

  1. Using a snap ring expander, install the snap ring.


21. INSPECT 3RD GEAR RADIAL CLEARANCE

C086543E01
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.008 to 0.034 mm (0.0003 to 0.0013 in.)

    1. If the clearance is not as specified, replace the needle roller bearing.


22. INSPECT 2ND GEAR RADIAL CLEARANCE

C086542E01
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.008 to 0.034 mm (0.0003 to 0.0013 in.)

    1. If the clearance is not as specified, replace the needle roller bearing.


23. INSPECT 1ST GEAR RADIAL CLEARANCE

C086541E01
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.009 to 0.056 mm (0.0004 to 0.0022 in.)

    1. If the clearance is not as specified, replace the needle roller bearing.

← REMOVAL (from Jun 2011)COMPONENTS (from Jun 2011) →