2014 Hilux · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. INSTALL OUTPUT SHAFT ASSEMBLY

C272938
  1. Apply gear oil to the sliding part of the output shaft.

  1. Using a plastic-faced hammer, install the output shaft by rapping the intermediate plate.


2. INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING

C272936
  1. Using a snap ring expander, install the shaft snap ring to the output shaft.


3. INSTALL INPUT SHAFT ASSEMBLY

D026006E02
  1. Apply gear oil to the input shaft and No. 2 synchronizer ring, and install them to the output shaft.

    NOTICE:
    1. Install the No. 2 synchronizer ring so that its groove fits into the No. 2 synchromesh shifting key.
    2. Check that the input shaft rotates slightly.


4. INSTALL COUNTER GEAR

D026005E02
  1. Temporarily install the counter gear to the intermediate plate.


5. INSTALL COUNTER SHAFT CENTER BEARING

C272975E01
  1. Using SST and a hammer, tap in a new center bearing to the intermediate plate.

    SST
    09316-60011   (09316-00011)

    HINT:
    Install the bearing while tapping the tip of the counter gear with a plastic hammer so that the counter gear will not hit the side wall of the output shaft gear by being pushed forward.


6. INSTALL REVERSE IDLER GEAR

D026002E02
  1. Apply gear oil to each sliding part of the reverse idler gear and the reverse idler gear shaft, and install the reverse idler gear and the reverse idler shaft to the intermediate plate.

    NOTICE:
    Face the groove side of the reverse idler shaft to the rear side, and install it from the rear side.


7. INSTALL REAR BEARING RETAINER

D026001E02
  1. Install the bearing retainer inserting to the groove of the reverse idler gear shaft with the 4 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }


8. INSTALL 5TH GEAR THRUST WASHER PIN

C272930
  1. Apply MP grease to the washer pin, and install it to the counter gear.


9. INSTALL 5TH GEAR THRUST WASHER

C272928
  1. Apply gear oil to the thrust washer, and install it to the counter gear.

    NOTICE:
    Install the thrust washer so that its chamfer side faces to the front side.


10. INSTALL NO. 3 SYNCHROMESH SHIFTING KEY
  1. Apply gear oil to the sliding part of No. 3 transmission hub sleeve, and install it to the counter 5th gear.

    NOTICE:
    Be sure of the direction of the No. 3 transmission hub sleeve and the counter 5th gear.

  1. C248514E02
    Install the 2 No. 3 synchromesh shifting keys and No. 3 synchromesh shifting key spring to the counter 5th gear as shown in the illustration.

    HINT:
    When installing the No. 3 synchromesh shifting key spring, make sure the protrusion fits into the cutout.

  1. C247403
    Using a snap ring expander, install the snap ring to the counter 5th gear.


11. INSTALL COUNTER 5TH GEAR BEARING

D026020E01
  1. Apply gear oil to the bearing and install it to the counter 5th gear.


12. INSTALL COUNTER 5TH GEAR

C272977
  1. Apply gear oil to the 5th gear and No. 3 transmission hub sleeve, and install it to the counter gear.


13. INSTALL NO. 3 SYNCHRONIZER RING

C272979
  1. Apply gear oil to the No. 3 synchronizer ring, and install it to the counter gear.

    NOTICE:
    Install the No. 3 synchronizer ring so that its groove fits into the No. 3 synchromesh shifting key.


14. INSTALL NO. 5 GEAR SPLINE PIECE

C272981E01
  1. Using SST and a press, press in the gear spline piece to the counter gear.

    SST
    09316-60011   (09316-00011)

    NOTICE:
    Check that the gear rotate freely.


15. INSTALL COUNTER GEAR REAR SHAFT SNAP RING
  1. Select the snap ring so that the thrust gap between the No. 5 gear spline piece and snap ring to be within the specification.

    Standard clearance:
    0.10 mm (0.0039 in.) or less

    Thickness
    2.80 to 2.85 mm (0.1102 to 0.1122 in.)
    2.85 to 2.90 mm (0.1122 to 0.1141 in.)
    2.90 to 2.95 mm (0.1141 to 0.1160 in.)
    2.95 to 3.00 mm (0.1160 to 0.1181 in.)
    3.00 to 3.05 mm (0.1181 to 0.1200 in.)
    3.05 to 3.10 mm (0.1200 to 0.1220 in.)
    3.10 to 3.15 mm (0.1220 to 0.1240 in.)

  1. C272983
    Using a brass bar and hammer, tap in the snap ring.


16. INSPECT COUNTER 5TH GEAR THRUST CLEARANCE

D025991E02
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.35 mm (0.0039 to 0.0138 in.)

    If the clearance is not as specified, replace the counter shaft 5th gear and No. 3 synchronizer ring.


17. INSPECT COUNTER 5TH GEAR RADIAL CLEARANCE

D025992E02
  1. Using a dial indicator, check the gear radial clearance.

    Standard clearance:
    0.015 to 0.068 mm (0.0006 to 0.0027 in.)

    If the clearance is not as specified, replace the counter 5th gear bearing.


18. INSTALL OUTPUT SHAFT REAR BEARING

D026024E01
  1. Using SST and a press, press in the spacer and a new rear bearing to the output shaft.

    SST
    09309-35010  


19. INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING
  1. Select a shaft snap ring so that the thrust gap between the output shaft bearing shaft and snap ring to be within the specification.

    Standard clearance:
    0.10 mm (0.0039 in.) or less

    Thickness
    Thickness
    2.65 to 2.70 mm (0.1043 to 0.1063 in.)
    3.10 to 3.15 mm (0.1220 to 0.1240 in.)
    2.70 to 2.75 mm (0.1063 to 0.1083 in.)
    3.15 to 3.20 mm (0.1240 to 0.1260 in.)
    2.75 to 2.80 mm (0.1083 to 0.1102 in.)
    3.20 to 3.25 mm (0.1260 to 0.1280 in.)
    2.80 to 2.85 mm (0.1102 to 0.1122 in.)
    3.25 to 3.30 mm (0.1280 to 0.1299 in.)
    2.85 to 2.90 mm (0.1122 to 0.1141 in.)
    3.30 to 3.35 mm (0.1299 to 0.1319 in.)
    2.90 to 2.95 mm (0.1141 to 0.1160 in.)
    3.35 to 3.40 mm (0.1319 to 0.1339 in.)
    2.95 to 3.00 mm (0.1160 to 0.1181 in.)
    3.40 to 3.45 mm (0.1339 to 0.1358 in.)
    3.00 to 3.05 mm (0.1181 to 0.1200 in.)
    3.45 to 3.50 mm (0.1358 to 0.1378 in.)
    3.05 to 3.10 mm (0.1200 to 0.1220 in.)
    -

  1. C273479
    Using a brass bar and hammer, tap in the snap ring.


20. INSTALL SPEEDOMETER DRIVE GEAR

G034243E04
  1. Using snap ring pliers, install the snap ring.

  1. Install the ball and drive gear.

  1. Using snap ring pliers, install the snap ring.


21. INSTALL REVERSE SHIFT ARM BRACKET

D025985E01
  1. Install the arm bracket on the intermediate plate with the 2 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }


22. INSTALL REVERSE SHIFT FORK

D026025E01
  1. Install the shift arm to the shift fork. Using a screwdriver and hammer, tap in a new E-ring.

  1. D026026E01
    Install the tip of the reverse shift arm to the reverse idler gear. Align the cut end of the reverse shift arm with the reverse shift arm bracket pin, and install them.


23. INSTALL NO. 4 SHIFT FORK SHAFT

D026027E01
  1. Install the compression spring and reverse shift fork ball to the reverse shift fork.

  1. D025981E01
    Apply gear oil to the sliding part of the No. 4 shift fork shaft.

  1. Using a screwdriver, install the No. 3 shift fork shaft by pushing the reverse shift fork ball lightly.

  1. D026028E01
    Using a brass bar and hammer, tap in the snap ring to the No. 4 shift fork shaft.


24. INSTALL NO. 3 SHIFT FORK SHAFT

D025979E02
  1. Install the reverse shift fork ball to the reverse shift fork.

  1. D025975E03
    Install the No. 1 shift interlock roller to the intermediate plate.

  1. C272922
    Install the No. 3 shift fork to the No. 3 transmission hub sleeve and No. 3 shift fork shaft to the intermediate plate from the front side.

  1. D029114E01
    Using a brass bar and hammer, tap in the snap ring to the shift fork shaft.

  1. C272920
    Using a 5 mm pin punch and hammer, tap in the slotted spring pin to the No. 3 shift fork.


25. INSTALL NO. 1 SHIFT FORK SHAFT

  1. D025975E04
    Install the No. 1 shift interlock roller to the intermediate plate.

  1. D029055E02
    Install the No. 1 shift fork to the reverse gear.

  1. D029054E02
    Install the No. 1 shift fork shaft to the intermediate plate from the rear side.

  1. D029053E02
    Install the shift fork set bolt to the No. 1 shift fork.

    Torque:
    20 N*m{ 204 kgf*cm , 14 ft.*lbf }

  1. D029115E01
    Using a brass bar and hammer, tap in the shift fork shaft snap ring to the No. 1 shift fork shaft.


26. INSTALL NO. 2 SHIFT SHAFT

D025967E02
  1. Install the shift interlock pin and No. 1 shift interlock roller to the intermediate plate.

  1. D029051E02
    Install the No. 2 shift fork to the No. 2 transmission hub sleeve.

  1. D029050E02
    Apply gear oil to the No. 2 shift fork, and install to the intermediate plate from the rear side.

  1. D029049E02
    Install the shift fork set bolt to the No. 2 shift fork.

    Torque:
    20 N*m{ 204 kgf*cm , 14 ft.*lbf }

  1. D029116E01
    Using a brass bar and a hammer, tap in the snap ring to the No. 2 shift fork shaft.


27. INSTALL NO. 1 SHIFT DETENT BALL SPRING SEAT

D033570E02
  1. Install the 2 compression springs and 2 shifts detent balls to the intermediate plate.

  1. D033569E02
    Using a T40 ''torx'' socket wrench, install the 3 spring seats to the intermediate plate.

    Torque:
    18.5 N*m{ 190 kgf*cm , 14 ft.*lbf }

  1. D025960E02
    Install the detent ball and low side compression spring to the intermediate plate.

  1. D029046E02
    Using a T40 ''torx'' socket wrench, install the spring seat to the intermediate plate.

    Torque:
    18.5 N*m{ 190 kgf*cm , 14 ft.*lbf }


28. INSTALL TRANSMISSION MAGNET

D025957E02
  1. Clean the transmission magnet, and install it to the intermediate plate.


29. INSTALL MANUAL TRANSMISSION CASE

D029067E03
  1. Apply seal packing to the manual transmission case as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. D029117E01
    Using a plastic-faced hammer, tap the transmission case to attach it to the intermediate plate.


30. INSTALL NO. 1 COUNTER GEAR FRONT BEARING SNAP RING

D025954E02
  1. Using a snap rig expander, install the snap ring to the transmission case.


31. INSTALL FRONT BEARING SHAFT SNAP RING

D025953E02
  1. Using a snap ring expander, install the snap ring to the transmission case.


32. INSTALL TRANSMISSION FRONT BEARING RETAINER OIL SEAL

D026035E01
  1. Using SST and a hammer, tap in a new oil seal to the front bearing retainer.

    SST
    09950-60010   (09951-00300, 09951-00520, 09952-06010)
    09950-70010   (09951-07100)

    Oil seal depth:
    11.20 to 12.20 mm (0.4409 to 0.4803 in.)

  1. Lightly apply MP grease to the tip of the oil seal.


33. INSTALL FRONT BEARING RETAINER

D026036E01
  1. Apply seal packing to the bearing retainer as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. D025950E02
    Install the bearing retainer front to the transmission case with the 8 bolts.

    Torque:
    16.5 N*m{ 170 kgf*cm , 12 ft.*lbf }

  1. Check that the input shaft and output shaft rotate smoothly.


34. INSTALL EXTENSION HOUSING OIL SEA

D033420E01
  1. Using SST and a hammer, tap in a new oil seal to the extension housing.

    SST
    09710-30050  
    09950-70010   (09951-07100)

    Oil seal depth:
    0 +- 0.5 mm (0 +- 0.020 in.)

    NOTICE:
    Be careful not to damage the oil seal lip.

  1. Lightly apply MP grease to the tip of the oil seal.


35. INSTALL REVERSE RESTRICT PIN

D029042E02
  1. Install the restrict pin to the extension housing.

  1. D033421E02
    Using a 5 mm pin punch and hammer, tap in the slotted pin to the extension housing.

  1. D029040E02
    Using a T40 ''torx'' socket wrench, install the reverse restrict pin plug to the transfer adapter.

    Torque:
    18.5 N*m{ 190 kgf*cm , 14 ft.*lbf }


36. INSTALL OIL RECEIVER
  1. Install the oil receiver with the bolt.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }


37. INSTALL OIL RECEIVER PIPE

D029037E02
  1. Install the oil receiver pipe to the extension housing.


38. INSTALL EXTENSION HOUSING

  1. D029067E02
    Apply seal packing to the extension housing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. Insert the shift and select lever to the extension housing.

  1. G034242E04
    Connect the shift and select lever to the fork shaft and put in the shift lever housing.

  1. Align the shift and select lever to the extension housing installation hole and push in the extension housing.

  1. B085186E01
    Install the extension housing to the case with the 10 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. G034547E02
    Install the shift lever housing bolt to the shift lever housing.

    Torque:
    33 N*m{ 340 kgf*cm , 25 ft.*lbf }


39. INSTALL CONTROL SHIFT LEVER RETAINER

C116363
  1. Install the control shift lever retainer and oil deflector.

  1. Install the 4 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }


40. INSTALL RESTRICT PIN

C116362E04
  1. Install the 2 restrict pins.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


41. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

D029030E02
  1. Using SST, install a new gasket and back-up light switch and to the transmission case.

    SST
    09817-16011  

    Torque:
    44 N*m{ 450 kgf*cm , 32 ft.*lbf }


42. INSTALL SPEEDOMETER DRIVE GEAR
  1. Install the new O-ring to the speedometer driven gear.

  1. Install the speedometer driven gear with the bolt.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }


43. INSTALL CLUTCH HOUSING

D029028E02
  1. Install the clutch housing to the transmission case with the 9 bolts.

    Torque:
    36 N*m{ 370 kgf*cm , 27 ft.*lbf }


44. INSTALL CLUTCH RELEASE FORK BOOT

D029027E02
  1. Install the fork boot to the clutch housing.


45. INSTALL RELEASE FORK SUPPORT

D025933E02
  1. Install the release fork support to the clutch housing.

    Torque:
    47 N*m{ 480 kgf*cm , 35 ft.*lbf }


46. INSTALL CLUTCH RELEASE BEARING ASSEMBLY

D029899E01
  1. Apply Multemp 8158 Grease or equivalent to the clutch release bearing, and install it to the clutch release fork.

    Grease:
    Multemp 8158 Grease or equivalent


47. INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

D029025E02
  1. Install the clutch release fork.

  1. Apply the clutch spline grease to the spline of the input shaft.


48. INSTALL DRAIN PLUG

D029024E02
  1. Install a new gasket and drain plug to the transmission case.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


49. INSTALL FILLER PLUG

D029023E02
  1. Install a new gasket and filler plug to the transmission case.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

← INSTALLATION (Jun 2011 – Jul 2012)INSTALLATION (from Aug 2013) →