HOW TO PROCEED WITH TROUBLESHOOTING
Troubleshooting · Vehicles built from Aug 2013
- HINT:
- Use the following procedure to troubleshoot the navigation system.
| 1.VEHICLE BROUGHT TO WORKSHOP |
| |||||
| 2.CUSTOMER PROBLEM ANALYSIS |
- When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
- Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
- The following 5 items are important points in problem analysis:
What
Vehicle model, system name
When
Date, time, occurrence frequency
Where
Road conditions
Under what conditions?
Driving conditions, weather conditions
How did it happen?
Problem symptoms
| |||||
| 3.INSPECT BATTERY VOLTAGE |
Measure the battery voltage.
- Standard voltage:
- 11 to 14 V
- HINT:
- If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
| |||||
| 4.CHECK CABIN |
Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.
- OK:
- Condensation is not likely being produced and the temperature is not high or extremely low.
- HINT:
- A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.
- The navigation system may not operate normally when the temperature is -20°C (-4°F) or less, or 65°C (149°F) or higher.
- A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.
|
|||||
| |||||
| 5.CHECK NAVIGATION SYSTEM NORMAL CONDITION |
Refer to Check Navigation System Normal Condition (Click here).
Result Result
Proceed to
Symptom is not normal operation.
A
Symptom is normal operation.
B
|
|||||
| |||||
| 6.CHECK FOR DTC |
Refer to DTC Check/Clear (Click here).
Result Result
Proceed to
DTCs are output.
A
DTCs are not output.
B
|
|||||
| |||||
| 7.DTC CLEAR |
Refer to DTC Check/Clear (Click here).
- HINT:
- The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.
| |||||
| 8.RECHECK FOR DTC |
Refer to DTC Check/Clear (Click here).
Result Result
Proceed to
DTCs are output.
A
DTCs are not output.
B
- HINT:
- Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.
- Check the DTCs and inspect the area that the code indicates.
- Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.
|
|||||
| |||||
| 9.DIAGNOSTIC TROUBLE CODE CHART |
Find the output code in Diagnostic Trouble Code Chart (Click here).
|
| 10.CHECK SD CARD |
Enter the "SD Check" screen. Refer to Check SD Card in Operation Check (Click here).
Result Result
Proceed to
"OK" is displayed.
A
"NG" is displayed.
B
|
|||||
| |||||
| 11.PROBLEM SYMPTOMS TABLE |
Refer to Problem Symptoms Table (Click here).
Result Result
Proceed to
Fault is not listed in Problem Symptoms Table.
A
Fault is listed in Problem Symptoms Table.
B
- HINT:
- If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms (Click here).
|
|||||
| |||||
| 12.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM |
Refer to Terminals of ECU (Click here).
| |||||
| 13.CHECK CIRCUIT |
Adjust, repair or replace as necessary.
| |||||
| 14.RECHECK FOR DTC |
After clearing DTCs, recheck for DTCs (Click here).
| |||||
| 15.PERFORM CONFIRMATION TEST |
| |||||