2014 Hilux · Service Manual BRAKE

C1241/41 Low Battery Positive Voltage or Abnormally High Battery Positive Voltage

Diagnostic trouble codes · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013

DESCRIPTION

This is the power source circuit of the skid control ECU.
The skid control ECU has a built-in brake actuator.
DTC No.
DTC Detection Condition
Trouble Area
C1241/41
When either of following is detected:
1. Both conditions continue for at least 10 seconds
  1. Vehicle speed is more than 3 km/h (2 mph)
  2. IG1 terminal voltage is less than 10 V
2. All conditions continue for at least 0.2 seconds
  1. Solenoid relay remains ON
  2. Relay contact is open
  3. IG1 terminal voltage is less than 10 V
  1. Battery
  2. Charging system
  3. Power source circuit

WIRING DIAGRAM

C108864E18

INSPECTION PROCEDURE


1. INSPECT FUSE (ECU-IG NO. 2)
  1. Remove the ECU-IG NO. 2 fuse from the engine room relay block, junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2. INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V

    Result 
    Result
    Proceed to
    Battery voltage is normal (when using intelligent tester)
    A
    Battery voltage is normal (when not using intelligent tester)
    B
    Battery voltage is abnormal
    C



B
Go to step 4

C
RECHARGE OR REPLACE BATTERY
A


3. READ VALUE USING INTELLIGENT TESTER (ECU IG POWER VOLTAGE)
  1. Using the Data List, check for proper functioning of the ECU IG power voltage.

    Skid control ECU 
    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    ECU IG Power Voltage
    ECU power supply voltage / TOO LOW / NORMAL / TOO HIGH
    TOO HIGH: more than 14.0 V
    NORMAL: 10 to 14.0 V
    TOO LOW: Below 10 V
    -
    Result 
    Result
    Proceed to
    Display is NORMAL
    A
    Display is not NORMAL
    B



B
Go to step 4
A

END

4. CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY)
C108884E03
  1. Disconnect the S2 ECU connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    S2-25 (IG1) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5. CHECK WIRE HARNESS (SKID CONTROL ECU - BODY GROUND)
C108884E04
  1. Disconnect the S2 ECU connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    S2-2 (GND1) - Body ground
    Below 1 Ω
    S2-24 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6. CHECK IF DTC OUTPUT RECURS
  1. Clear the DTCs.

  1. Drive the vehicle at approximately 30 km/h (19 mph) or more for 60 seconds or more.

  1. Check for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY


← C1241/41 Low Battery Positive Voltage or Abnormally High Battery Positive Voltage (Jun 2011 – Jul 2013)C1243/43 Acceleration Sensor Stuck Malfunction (+ C1244/44, C1245/45, C1279/79) (from Jun 2011) →