2014 Hilux · Service Manual BODY ELECTRICAL

Tachometer Malfunction

Circuit diagnosis · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

In this circuit, the combination meter assembly receives engine speed signals from the ECM. The meter CPU displays the engine speed, which is calculated based on the data received from the ECM.

WIRING DIAGRAM

E261910E01
E261910E02
E261910E03
E261910E04
E261910E05

INSPECTION PROCEDURE


1. CHECK COMBINATION METER ASSEMBLY
E232461E01
  1. Disconnect the C25 combination meter assembly connector.

  1. Using an oscilloscope, check the signal waveform of the meter.

    Item
    Condition
    Tester Connection
    C25-7 (S) - Body ground
    Tool Setting
    5 V/DIV., 10 msec./DIV.
    Condition
    Engine idling

    OK:
    The waveform displayed is as shown in the illustration.

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)

    HINT:
    As the engine speed increases, the wavelength shortens.



NG
Go to step 2
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

2. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
  1. *1: for 1TR-FE, 2TR-FE
  2. *2: for 1KD-FTV, 2KD-FTV
  3. *3: for 1GR-FE
  4. *4: for 5L-E
  1. Disconnect the C25 combination meter assembly connector.

  1. Disconnect the E10*1 or E5*2 or E13*3 or E21*4 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1TR-FE, 2TR-FE 
    Tester Connection
    Condition
    Specified Condition
    C25-7 (S) - E10-1 (TACH)
    Always
    Below 1 Ω
    C25-7 or E10-1 (TACH) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV w/o DPF, 2KD-FTV w/o DPF 
    Tester Connection
    Condition
    Specified Condition
    C25-7 (S) - E5-4 (TACH)
    Always
    Below 1 Ω
    C25-7 (S) or E5-4 (TACH) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV w/ DPF, 2KD-FTV w/ DPF 
    Tester Connection
    Condition
    Specified Condition
    C25-7 (S) - E31-18 (TACH)
    Always
    Below 1 Ω
    C25-7 (S) or E31-18 (TACH) - Body ground
    Always
    10 kΩ or higher
    for 1GR-FE 
    Tester Connection
    Condition
    Specified Condition
    C25-7 (S) - E13-1 (TACH)
    Always
    Below 1 Ω
    C25-7 or E13-1 (TACH) - Body ground
    Always
    10 kΩ or higher
    for 5L-E 
    Tester Connection
    Condition
    Specified Condition
    C25-7 (S) - E21-7 (TACH)
    Always
    Below 1 Ω
    C25-7 or E21-7 (TACH) - Body ground
    Always
    10 kΩ or higher

Result 
Result
Proceed to
NG
A
OK (for 1TR-FE, 2TR-FE, 1GR-FE)
B
OK (for 1KD-FTV, 2KD-FTV, 5L-E)
C


B
GO TO SFI SYSTEM

C
GO TO ECD SYSTEM
A

REPAIR OR REPLACE HARNESS OR CONNECTOR


← Tachometer Malfunction (Aug 2012 – Jul 2013)Fuel Receiver Gauge Malfunction (Jun 2011 – Jul 2012) →