TERMINALS OF ECU
System information · Vehicles built from Nov 2011
Versions by build date: Jun 2011 – Oct 2011 from Nov 2011
| CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY |


| *1 |
Integration Relay |
- |
- |
Disconnect the 2D, 2H and 2L driver side junction block assembly connectors.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
2D-9 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
2D-18 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
2H-4 (ALTB) - Body ground
LG - Body ground
Battery power supply
Always
11 to 14 V
2L-12 (BECU) - Body ground
L - Body ground
Battery power supply
Always
11 to 14 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the 2D, 2H and 2L driver side junction block assembly connectors.
Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
2A-4 (L1) - Body ground
L - Body ground
- Power window regulator master switch assembly (door control switch) lock input signal
- Driver side door key-linked lock input signal
- Power window regulator master switch assembly (door control switch) locked
- Driver side door key cylinder in lock position
Below 1 V
- Power window regulator master switch assembly (door control switch) off
- Ignition switch off, all doors closed and driver side door key cylinder in neutral position
11 to 14 V
2D-4 (UL1) - Body ground
L-W - Body ground
- Power window regulator master switch assembly (door control switch) unlock input signal
- Driver side door key-linked unlock input signal
- Power window regulator master switch assembly (door control switch) unlocked
- Driver side door key cylinder in unlock position
Below 1 V
- Power window regulator master switch assembly (door control switch) off
- Ignition switch off, all doors closed and driver side door key cylinder in neutral position
11 to 14 V
2K-10 (ACT-) - Body ground
L-Y - Body ground
Door lock motor unlock drive output signal (passenger door, and rear RH door*1, *3 or rear LH door*2, *3)
Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position
Below 1 V
Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in unlock position
11 to 14 V
2K-11 (ACT+) - Body ground
L - Body ground
Door lock motor lock drive output signal (passenger door, and rear RH door*1, *3 or rear LH door*2, *3)
Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position
Below 1 V
Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in lock position
11 to 14 V
2O-27 (DCTY) - Body ground
R-B - Body ground
Front door courtesy light switch assembly LH*1 or RH*2 input signal
Driver side door open
Below 1 V
Driver side door closed
11 to 14 V
2R-27 (ACT-) - Body ground
L-Y - Body ground
Door lock motor unlock drive output signal (driver door, and rear LH door*1, *3 or rear RH door*2, *3)
Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position
Below 1 V
Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in unlock position
11 to 14 V
2R-28 (ACT+) - Body ground
L - Body ground
Door lock motor lock drive output signal (driver door, and rear LH door*1, *3 or rear RH door*2, *3)
Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position
Below 1 V
Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in lock position
11 to 14 V
- *1: for LHD
- *2: for RHD
- *3: for Double Cab
- If the result is not as specified, the driver side junction block assembly may have a malfunction.
- Power window regulator master switch assembly (door control switch) lock input signal
| CHECK THEFT WARNING ECU ASSEMBLY (w/ Theft Deterrent System) |
Disconnect the T36 theft warning ECU assembly connector.

Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
T36-1 (E) - Body ground
B-W - Body ground
Ground
Always
Below 1 Ω
T36-4 (+B1) - Body ground
L-Y - Body ground
Battery power supply
Always
11 to 14 V
T36-14 (+B2) Body ground
G - Body ground
Battery power supply
Always
11 to 14 V
T36-18 (IG) Body ground
R-L - Body ground
Ignition power supply
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the T36 theft warning ECU assembly connector.
Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
T36-7 (CTY) - Body ground
R-L - Body ground
All Door courtesy switches input signal
One or more doors open
Below 1 V
All doors closed
11 to 14 V
T36-17 (SPD) - Body ground
V-R - Body ground
Vehicle speed input signal
Driving at approximately 20 km/h (12.4 mph)
Pulse generation (See waveform 1)
- If the result is not as specified, the theft warning ECU assembly may have a malfunction.
- If the result is not as specified, the theft warning ECU assembly may have a malfunction.
Inspect using an oscilloscope.
- HINT:
- The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
- As the vehicle speed increases, the wavelength shortens.
- The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)

Measurement Condition Item
Content
Tester Connection
T36-17 (SPD) - Body ground
Tool Setting
5 V/DIV., 10 msec./DIV.
Condition
Driving at approximately 20 km/h (12.4 mph)