2014 Hilux · Service Manual BODY ELECTRICAL

Fuel Receiver Gauge Malfunction

Circuit diagnosis · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

  1. The fuel sender gauge has a variable resistance mechanism. The resistance decreases when the fuel amount increases, and the resistance increases when the fuel amount decreases. The fuel receiver gauge changes based on the resistance of the fuel sender gauge.

NOTICE:
When the combination meter is removed or replaced, its connector is disconnected or fuel is added, the fuel receiver gauge display will return to normal within a maximum of 16 minutes after the ignition switch is turned to ON or when vehicle speed is input.


WIRING DIAGRAM

E229997E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SUCTION WITH PUMP AND GAUGE TUBE OR FUEL TANK VENT TUBE)
  1. Disconnect the C25 combination meter assembly connector.

  1. Disconnect the F15 fuel suction with pump and gauge tube assembly*1 or F13 fuel tank vent tube sub-assembly*2 connector.

    1. *1: for 1TR-FE, 2TR-FE, 1GR-FE
    2. *2: for 1KD-FTV, 2KD-FTV, 5L-E

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1TR-FE, 2TR-FE, 1GR-FE 
    Tester Connection
    Condition
    Specified Condition
    C25-2 (ES) - F15-3 (FE)
    Always
    Below 1 Ω
    C25-3 (L) - F15-2 (FS)
    Always
    Below 1 Ω
    C25-2 (ES) - C25-3 (L)
    Always
    10 kΩ or higher
    C25-2 (ES) - Body ground
    Always
    10 kΩ or higher
    C25-3 (L) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV, 2KD-FTV, 5L-E 
    Tester Connection
    Condition
    Specified Condition
    C25-2 (ES) - F13-3 (FE)
    Always
    Below 1 Ω
    C25-3 (L) - F13-2 (FS)
    Always
    Below 1 Ω
    C25-2 (ES) - C25-3 (L)
    Always
    10 kΩ or higher
    C25-2 (ES) - Body ground
    Always
    10 kΩ or higher
    C25-3 (L) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE OR FUEL TANK VENT TUBE
E226597E01
  1. Remove the fuel suction with pump and gauge tube assembly*1 or fuel tank vent tube sub-assembly*2.

    1. *1: for 1TR-FE, 2TR-FE, 1GR-FE
    2. *2: for 1KD-FTV, 2KD-FTV, 5L-E

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 - B-2
    Always
    Below 1 Ω
    A-3 - B-1
    Always
    Below 1 Ω
    A-2 - A-3
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Upper Side
    *b
    Lower Side
    (to Fuel Sender Gauge Assembly)
    *c
    Connector A
    *d
    Connector B
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1TR-FE, 2TR-FE, 1GR-FE)
    B
    NG (for 1KD-FTV, 2KD-FTV, 5L-E)
    C



B
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

C
REPLACE FUEL TANK VENT TUBE SUB-ASSEMBLY
A


3. INSPECT FUEL SENDER GAUGE ASSEMBLY
  1. Remove the fuel sender gauge assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float position F (upper)
    3 to 5 Ω
    Float position E (lower)
    109 to 111 Ω



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Fuel Receiver Gauge Malfunction (Aug 2012 – Jul 2013)Engine Coolant Temperature Gauge Malfunction (Jun 2011 – Jul 2012) →