2014 Hilux · Service Manual HEATER & AIR CONDITIONING SYSTEM

TERMINALS OF ECU

System information · Vehicles built from Jun 2011


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/o PTC HEATER)
I100991E02
  1. Disconnect the A9 air conditioning amplifier connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IG+ (A9-10) - GND (A9-18)
    R-L - L
    Power source (IG)
    Ignition switch OFF
    Below 1 V
    IG+ (A9-10) - GND (A9-18)
    R-L - L
    Power source (IG)
    Ignition switch ON
    10 to 14 V
    GND (A9-18) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    ACON (A9-4) - GND (A9-18)
    R-G - L
    A/C switch signal
    A/C switch OFF
    Below 1 V
    ACON (A9-4) - GND (A9-18)
    R-G - L
    A/C switch signal
    A/C switch ON
    10 to 14 V
    IND- (A9-13) - GND (A9-18)
    R-L - L
    A/C indicator light signal
    A/C switch OFF
    Below 1 V
    IND- (A9-13) - GND (A9-18)
    R-L - L
    A/C indicator light signal
    A/C switch ON
    10 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the A9 connector.

  4. Measure the voltage and resistance of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    PSW (A9-3) - GND (A9-18)
    Y-B - L
    Air conditioner pressure switch signal
    Ignition switch START
    Refrigerant pressure normal: 0.18 MPa (1.9 kgf/cm2, 26 psi) to 3.03 MPa (31.0 kgf/cm2, 440 psi)
    A/C switch ON
    Blower switch ON
    10 to 14 V
    PSW (A9-3) - GND (A9-18)
    Y-B - L
    Air conditioner pressure switch signal
    Ignition switch START
    Refrigerant pressure less than 0.18 MPa (1.9 kgf/cm2, 26 psi) or more than 3.03 MPa (31.0 kgf/cm2, 440 psi)
    A/C switch ON
    Blower switch ON
    Below 1 V
    TE (A9-7) - SG-1 (A9-8)
    G - P
    Evaporator temperature sensor signal
    Ignition switch ON
    Evaporator temperature is 0°C (32°F)
    Temperature control knob: MAX COOL
    2.0 to 2.4 V
    TE (A9-7) - SG-1 (A9-8)
    G - P
    Evaporator temperature sensor signal
    Ignition switch ON
    Evaporator temperature is 15°C (59°F)
    Temperature control knob: MAX COOL
    1.4 to 1.8 V
    SG-1 (A9-8) - Body ground
    P - Body ground
    Ground for evaporator temperature sensor
    Always
    Below 1 Ω
    MGC (A9-1) - GND (A9-18)
    L-W - L
    Magnet clutch signal
    Ignition switch START
    Magnet clutch is not engaged
    Below 1 V
    MGC (A9-1) - GND (A9-18)
    L-W - L
    Magnet clutch signal
    Ignition switch START
    Magnet clutch is engaged
    10 to 14 V
    ACT (A9-2) - GND (A9-18)
    R-L - L
    Magnet on permit signal
    Ignition switch START
    A/C switch OFF
    Blower switch ON
    Below 1 V
    ACT (A9-2) - GND (A9-18)
    R-L - L
    Magnet on permit signal
    Ignition switch START
    A/C switch ON
    Blower switch ON
    10 to 14 V
    AC1 (A9-14) - GND (A9-18)
    Y - L
    Idle-up request signal
    Ignition switch START
    Magnet clutch is not engaged
    10 to 14 V
    AC1 (A9-14) - GND (A9-18)
    Y - L
    Idle-up request signal
    Ignition switch START
    Magnet clutch is engaged
    Below 1 V
    1. If the result is not as specified, the air conditioning amplifier may have a malfunction.


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ PTC HEATER)
I100992E06
  1. Disconnect the A48 air conditioning amplifier connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IG (A48-20) - GND (A48-29)
    R-L - Y
    Power source (IG)
    Ignition switch OFF
    Below 1V
    IG (A48-20) - GND (A48-29)
    R-L - Y
    Power source (IG)
    Ignition switch ON
    10 to 14 V
    GND (A48-29) - Body ground
    Y - Body ground
    Ground
    Always
    Below 1 Ω
    ACON (A48-8) - GND (A48-29)
    R-G - Y
    A/C switch signal
    Ignition switch ON
    Blower switch OFF
    A/C switch OFF
    Below 1 V
    ACON (A48-8) - GND (A48-29)
    R-G - Y
    A/C switch signal
    Ignition switch ON
    Blower switch ON
    A/C switch ON
    10 to 14 V
    IND- (A48-9) - GND (A48-29)
    R-L - Y
    A/C indicator light signal
    Ignition switch ON
    Blower switch OFF
    A/C switch OFF
    Below 1 V
    IND- (A48-9) - GND (A48-29)
    R-L - Y
    A/C indicator light signal
    Ignition switch ON
    Blower switch ON
    A/C switch ON
    10 to 14 V
    BLW (A48-38) - GND (A48-29)
    R-L - Y
    Max. HOT switch signal
    Ignition switch ON
    Temperature control knob: Max HOT
    Below 1 Ω
    BLW (A48-38) - GND (A48-29)
    R-L - Y
    Max. HOT switch signal
    Ignition switch ON
    Temperature control knob: except Max HOT
    10 kΩ or higher
    HEAT (A48-5) - GND (A48-29)
    L-O - Y
    Heater switch signal
    Heater switch ON
    Below 1 Ω
    HEAT (A48-5) - GND (A48-29)
    L-O - Y
    Heater switch signal
    Heater switch OFF
    10 kΩ or higher
    MGC (A48-19) - GND (A48-29)
    B - Y
    Magnet clutch relay signal
    Ignition switch ON
    Blower switch ON
    10 to 14 V
    MGC (A48-19) - GND (A48-29)
    B - Y
    Magnet clutch relay signal
    Ignition switch ON
    Blower switch OFF
    Below 1 V
    TAIL (A48-7) - GND (A48-29)
    G - Y
    Light control switch signal
    Light control switch ON
    10 to 14 V
    TAIL (A48-7) - GND (A48-29)
    G - Y
    Light control switch signal
    Light control switch OFF
    Below 1 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the A48 connector.

  4. Measure the voltage and resistance of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    PSW (A48-4) - GND (A48-29)
    Y-B - Y
    air conditioner pressure switch signal
    Ignition switch START
    Refrigerant pressure normal: 0.18 MPa (1.9 kgf/cm2, 26 psi) to 3.03 MPa (31.0 kgf/cm2, 440 psi)
    A/C switch ON
    Blower switch ON
    10 to 14 V
    PSW (A48-4) - GND (A48-29)
    Y-B - Y
    air conditioner pressure switch signal
    Ignition switch START
    Refrigerant pressure less than 0.18 MPa (1.9 kgf/cm2, 26 psi) or more than 3.03 MPa (31.0 kgf/cm2, 440 psi)
    A/C switch ON
    Blower switch ON
    Below 1 V
    TE (A48-24) - SG-1 (A48-31)
    G - P
    Evaporator temperature sensor signal
    Ignition switch ON
    Evaporator temperature is 0°C (32°F)
    Temperature control knob: MAX COOL
    2.0 to 2.4 V
    TE (A48-24) - SG-1 (A48-31)
    G - P
    Evaporator temperature sensor signal
    Ignition switch ON
    Evaporator temperature is 15°C (59°F)
    Temperature control knob: MAX COOL
    1.4 to 1.8 V
    SG-1 (A48-31) - Body ground
    P - Body ground
    Ground for evaporator temperature sensor
    Always
    Below 1 Ω
    MGC (A48-19) - GND (A48-29)
    B - Y
    Magnet clutch signal
    Ignition switch START
    Magnet clutch is not engaged
    Below 1 V
    MGC (A48-19) - GND (A48-29)
    B - Y
    Magnet clutch signal
    Ignition switch START
    Magnet clutch is engaged
    10 to 14 V
    ACT (A48-39) - GND (A48-29)
    R-L - Y
    Magnet on permit signal
    Ignition switch START
    A/C switch OFF
    Blower switch OFF
    Below 1 V
    ACT (A48-39) - GND (A48-29)
    R-L - Y
    Magnet on permit signal
    Ignition switch START
    A/C switch ON
    Blower switch ON
    10 to 14 V
    AC1 (A48-35) - GND (A48-29)
    Y - Y
    Idle-up request signal
    Ignition switch START
    Magnet clutch is not engaged
    10 to 14 V
    AC1 (A48-35) - GND (A48-29)
    Y - Y
    Idle-up request signal
    Ignition switch START
    Magnet clutch is engaged
    Below 1.0 V
    BLW (A48-38) - GND (A48-29)
    R-L - Y
    Max. HOT switch signal
    Ignition switch ON
    Blower switch ON
    temperature control knob: Max HOT
    Heater switch ON
    Coolant temperature 65°C (149°F)
    10 to 14 V
    BLW (A48-38) - GND (A48-29)
    R-L - Y
    Max. HOT switch signal
    Ignition switch ON
    Blower switch ON
    Temperature control knob: except Max HOT
    Heater switch OFF
    Coolant temperature 65°C (149°F)
    Below 1 V
    HEAT (A48-5) - GND (A48-29)
    L-O - Y
    Heater switch input signal
    Ignition switch ON
    Blower switch ON
    temperature control knob: Max HOT
    Heater switch ON
    Coolant temperature 65°C (149°F)
    Below 1 V
    HEAT (A48-5) - GND (A48-29)
    L-O - Y
    Heater switch input signal
    Ignition switch ON
    Blower switch ON
    Temperature control knob: except Max HOT
    Heater switch OFF
    Coolant temperature 65°C (149°F)
    10 to 14 V
    SWIN (A48-15) - GND (A48-29)
    P - Y
    Heater switch indicator light signal
    Ignition switch ON
    Blower switch ON
    temperature control knob: Max HOT
    Heater switch ON
    Coolant temperature 65°C (149°F)
    Below 1 V
    SWIN (A48-15) - GND (A48-29)
    P - Y
    Heater switch indicator light signal
    Ignition switch ON
    Blower switch ON
    Temperature control knob: except Max HOT
    Heater switch OFF
    Coolant temperature 65°C (149°F)
    10 to 14 V
    PTCR (A48-26) - GND (A48-29)
    L-W - Y
    Heater switch output signal
    Ignition switch ON
    Blower switch ON
    temperature control knob: Max HOT
    Heater switch ON
    Coolant temperature 65°C (149°F)
    10 to 14 V
    PTCR (A48-26) - GND (A48-29)
    L-W - Y
    Heater switch output signal
    Ignition switch ON
    Blower switch ON
    Temperature control knob: except Max HOT
    Heater switch OFF
    Coolant temperature 65°C (149°F)
    Below 1 V
    TW (A48-32) - GND (A48-29)
    P - Y
    Water temperature signal
    Ignition switch ON
    Pulse generation
    TACO (A48-33) - GND (A48-29)
    B-W - Y
    Tachometer signal
    Engine running
    Pulse generation
    (see waveform 1)
    ALT (A48-37) - GND (A48-29)
    G - Y
    Generator
    Engine running
    Pulse generation
    PTC1 (A48-3) - GND (A48-29)
    R-W - Y
    PTC heater relay signal
    Ignition switch ON
    Blower switch ON
    temperature control knob: Max HOT
    Heater switch ON
    Coolant temperature 65°C (149°F)
    Below 1 V
    PTC1 (A48-3) - GND (A48-29)
    R-W - Y
    PTC heater relay signal
    Ignition switch ON
    Blower switch ON
    Temperature control knob: except Max HOT
    Heater switch OFF
    Coolant temperature 65°C (149°F)
    10 to 14 V
    PTC2 (A48-2) - GND (A48-29)
    GR - Y
    PTC heater relay signal
    Ignition switch ON
    Blower switch ON
    temperature control knob: Max HOT
    Heater switch ON
    Coolant temperature 65°C (149°F)
    Below 1 V
    PTC2 (A48-2) - GND (A48-29)
    GR - Y
    PTC heater relay signal
    Ignition switch ON
    Blower switch ON
    Temperature control knob: except Max HOT
    Heater switch OFF
    Coolant temperature 65°C (149°F)
    10 to 14 V
    1. If the result is not as specified, the air conditioning amplifier may have a malfunction.

  5. I042330E03
    Inspect using an oscilloscope.

    1. Waveform 1 (Reference)

      Item
      Content
      Symbols (Terminal No.)
      TACO (A48-33) - GND (A48-29)
      Tool Setting
      5 V/DIV., 20 msec./DIV.
      Condition
      Engine idling

      HINT:
      As engine speed increases, the wavelength shortens.


CHECK ECM
A066714E25

  1. Measure the voltage of the connectors.

    1. 1TR-FE, 2TR-FE

      Symbols (Terminal No.)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      ACT (E10-25) - E01 (E12-7)
      R-L - W-B
      Magnet on permit signal
      Ignition switch START
      A/C switch OFF
      Blower switch OFF
      Below 1 V
      ACT (E10-25) - E01 (E12-7)
      R-L - W-B
      Magnet on permit signal
      Ignition switch START
      A/C switch ON
      Blower switch ON
      10 to 14 V
      AC1 (E10-24) - E01 (E12-7)
      Y - W-B
      Idle-up request signal
      Ignition switch START
      Magnet clutch is engaged
      Below 1.0 V
      AC1 (E10-24) - E01 (E12-7)
      Y - W-B
      Magnet on permit signal
      Ignition switch START
      Magnet clutch is not engaged
      10 to 14 V
      1. If the result is not as specified, the ECM may have a malfunction.

    2. 1KD-FTV, 2KD-FTV

      Symbols (Terminal No.)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      ACT (E6-19) - E01 (E8-7)
      R-L - W-B
      Magnet on permit signal
      Ignition switch START
      A/C switch OFF
      Blower switch OFF
      Below 1 V
      ACT (E6-19) - E01 (E8-7)
      R-L - W-B
      Magnet on permit signal
      Ignition switch START
      A/C switch ON
      Blower switch ON
      10 to 14 V
      AC1 (E6-18) - E01 (E8-7)
      Y - W-B
      Idle-up request signal
      Ignition switch START
      Magnet clutch is engaged
      Below 1 V
      AC1 (E6-18) - E01 (E8-7)
      Y - W-B
      Magnet on permit signal
      Ignition switch START
      Magnet clutch is not engaged
      10 to 14 V
      THWO (E5-2) - E01 (E8-7)*
      P - W-B
      Water temperature signal
      Ignition switch START
      Pulse generation
      HSW (E6-20) - E01 (E8-7)*
      L-W - W-B
      Heater switch output signal for idle-up
      Ignition switch START
      Heater switch ON
      Blower switch ON
      Temperature control knob: Max HOT
      Coolant temperature 65°C (149 °F)
      Below 1 V
      HSW (E6-20) - E01(E8-7)*
      L-W - W-B
      Heater switch output signal for idle-up
      Ignition switch START
      Heater switch OFF
      Blower switch ON
      Temperature control knob: except Max HOT
      Coolant temperature 65°C (149 °F)
      10 to 14 V
      TACH (E5-4) - E01 (E8-7)*
      B-W - W-B
      Tachometer signal
      Engine running
      Pulse generation
      (see waveform 1)
      1. If the result is not as specified, the ECM may have a malfunction.

        HINT:
        *: w/ PTC Heater

    3. 1GR-FE

      Symbols (Terminal No.)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      ACT (E13-25) - E01 (E15-7)
      R-L - W-B
      Magnet on permit signal
      Ignition switch START
      A/C switch OFF
      Blower switch OFF
      Below 1 V
      ACT (E13-19) - E01 (E15-7)
      R-L - W-B
      Magnet on permit signal
      Ignition switch START
      A/C switch ON
      Blower switch ON
      10 to 14 V
      AC1 (E13-24) - E01 (E15-7)
      Y - W-B
      Idle-up request signal
      Ignition switch START
      Magnet clutch is engaged
      Below 1 V
      AC1 (E13-24) - E01 (E15-7)
      Y - W-B
      Magnet on permit signal
      Ignition switch START
      Magnet clutch is not engaged
      10 to 14 V
      1. If the result is not as specified, the ECM may have a malfunction.

    4. 5L-E
      A002958E04

      Symbols (Terminal No.)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      ACT (E21-8) - E01 (E23-13)
      R-L - W-B
      Magnet on permit signal
      Ignition switch START
      A/C switch OFF
      Blower switch OFF
      Below 1 V
      ACT (E21-8) - E01 (E23-13)
      R-L - W-B
      Magnet on permit signal
      Ignition switch START
      A/C switch ON
      Blower switch ON
      10 to 14 V
      AC1 (E21-2) - E01 (E23-13)
      Y - W-B
      Idle-up request signal
      Ignition switch START
      Magnet clutch is engaged
      Below 1 V
      AC1 (E21-2) - E01 (E23-13)
      Y - W-B
      Magnet on permit signal
      Ignition switch START
      Magnet clutch is not engaged
      10 to 14 V
      1. If the result is not as specified, the ECM may have a malfunction.

  2. I042330E03
    Inspect using an oscilloscope (w/ PTC heater only).

    1. Waveform 1 (Reference)

      Item
      Content
      Symbols (Terminal No.)
      TACH (E5-4) - E01 (E8-7)
      Tool Setting
      5 V/DIV., 20 msec./DIV.
      Condition
      Engine idling

      HINT:
      As engine speed increases, the wavelength shortens.

← PROBLEM SYMPTOMS TABLE (from Jun 2011)ON-VEHICLE INSPECTION (from Jun 2011) →