P0504 Brake Switch "A" / "B" Correlation
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The signals of the stop light switch's duplex system (STP and ST1-) are used to judge whether the brake system is abnormal or not. When the signals of depressing and releasing the brake pedal are detected simultaneously, the ECM interprets this as a malfunction of the stop light switch.- HINT:
- Normal condition is shown in the table below.
Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (1), (2) and (3) continue for 0.5 seconds or more: - Ignition switch is ON
- Brake pedal is released
- STP signal is OFF when ST1- signal is OFF
- Short in stop light switch signal circuit
- Stop light switch
- ECM
- Ignition switch is ON
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK STOP LIGHT (OPERATION) |
Check the stop lights operation when the brake pedal is depressed and released.
- OK:
- Stop lights turn on when brake pedal is depressed, and turn off when brake pedal is released.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (STP SIGNAL, ST1- VOLTAGE) |
![]() ![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine / Data List / Stop Light Switch.
Check the result.
- OK:
Brake Pedal
Specified Condition
Depressed
STP signal ON
Released
STP signal OFF
Measure the voltage of the ECM connectors.
- Standard voltage:
Tester Connection
Brake Pedal
Specified Condition
E6-14 (ST1-) - E7-7 (E1)
Depressed
Below 1.5 V
E6-14 (ST1-) - E7-7 (E1)
Released
7.5 to 14 V
|
|
||||
| NG | |
| 3. INSPECT STOP LIGHT SWITCH ASSEMBLY |
![]() ![]() |
Remove the stop light switch.
Measure the resistance of the switch.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Pin not pushed
Below 1 Ω
3 - 4
Pin not pushed
10 kΩ or higher
1 - 2
Pin pushed
10 kΩ or higher
3 - 4
Pin pushed
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM) |
![]() ![]() |
Disconnect the S14 stop light switch connector.
Disconnect the E6 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
S14-1 - E6-15 (STP)
Below 1 Ω
S14-4 - E6-14 (ST1-)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
S14-1 or E6-15 (STP) - Body ground
10 kΩ or higher
S14-4 or E6-14 (ST1-) - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||



