2014 Hilux · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
When working with seal packing material, perform the following:
  1. Using a razor blade and gasket scraper, remove all old seal packing material from the gasket surfaces.
  2. Clean all components thoroughly to remove all foreign matter.
  3. Clean both sealing surfaces with a non-residue solvent.
  4. Apply seal packing in a continuous line approximately 2 to 3 mm (0.0788 to 0.118 in.) in diameter on the sealing surface.
  5. Reassemble parts within 10 minutes of applying seal packing material. Failing to do so will require the seal packing material to be removed and reapplied.


1. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

  1. AT08393E01
    Align the groove of the manual valve with the pin of the lever.

  1. D029011E08
    Install the 20 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.

    Bolt length:
    23 mm (0.91 in.) for A
    28 mm (1.10 in.) for B
    36 mm (1.42 in.) for C


2. CONNECT TRANSMISSION WIRE

  1. G037235E01
    Connect the 4 connectors to the 4 shift solenoid valves.


3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

C118025E01
  1. Install 3 new gaskets.

  1. D028706E03
    Install the oil strainer with the 4 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.

    Bolt length:
    14 mm (0.55 in.) for A
    20 mm (0.79 in.) for B
    23 mm (0.91 in.) for C


4. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

D029014E02

HINT:
Remove any packing material and be careful not to spill oil on the contacting surfaces of the transmission case and oil pan.

  1. Install the 3 magnets to the locations indicated in the illustration.

  1. D028715E01
    Apply seal packing to the oil pan as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281,
    Three Bond 1281 or equivalent

  1. Install the oil pan with the 19 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


5. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

C118024
  1. Coat a new O-ring with ATF, and install it to the oil filler tube.

  1. Install the oil filler tube with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Install the oil dipstick.


6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

7. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable to the negative (-) battery terminal.


8. ADD AUTOMATIC TRANSMISSION FLUID

Fluid type:
Toyota Genuine ATF Type T-IV


9. INSPECT AUTOMATIC TRANSMISSION FLUID
  1. Inspect the automatic transmission fluid (Click here).

← REMOVAL (from Jun 2011)INSTALLATION (Aug 2012 – Jul 2013) →