2014 Hilux · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Jun 2011


1. REMOVE DRAIN PLUG SUB-ASSEMBLY

2. REMOVE BREATHER HOSE

C118279E01
  1. Remove the bolt and breather hose.


3. REMOVE TRANSMISSION CONTROL SHAFT LEVER LH

D028070E01
  1. Remove the nut, washer and control shaft lever.


4. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

G037204E01
  1. Using a screwdriver, unstake the lock washer.

  1. Remove the nut and lock washer.

  1. Remove the bolt and park/neutral position switch.

    HINT:
    Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.


5. REMOVE ATF TEMPERATURE SENSOR

  1. C239915
    Detach the sensor connector clamp from the wire harness bracket.

  1. Using a 19 mm union nut wrench, remove the ATF temperature sensor from the automatic transmission assembly.

  1. Remove the O-ring from the ATF temperature sensor.

  1. Remove the bolt and wire harness bracket.


6. REMOVE OIL COOLER TUBE UNION

G034863E01
  1. Remove the 2 tube unions.

  1. Remove the O-rings from each tube union.


7. REMOVE SPEED SENSOR (NO0)

Q003894E01
  1. Remove the bolt and sensor.

  1. Remove the O-ring from the sensor.


8. REMOVE SPEED SENSOR (SP2)

G035550E01
  1. Remove the bolt and sensor.

  1. Remove the O-ring from the sensor.


9. REMOVE AUTOMATIC TRANSMISSION HOUSING

C118280
  1. Remove the 6 bolts.

  1. Remove the transmission housing.


10. FIX TRANSMISSION CASE

AT05092E01
  1. Install the transmission case on the overhaul attachment.


11. REMOVE REAR TRANSFER ADAPTER

D028071E01
  1. Remove the 8 bolts.

  1. Remove the rear transfer adaptor.


12. REMOVE TRANSFER CASE ADAPTER REAR OIL SEAL

D027909E01
  1. Using a screwdriver, pry out the oil seal.

    NOTICE:
    Do not damage the rear transfer adapter.


13. REMOVE REAR TRANSFER CASE ADAPTER OIL RECEIVER

  1. C212453
    Using snap ring expander, remove the snap ring.

  1. Remove the rear transfer case adaptor oil receiver from the rear transfer adaptor.


14. REMOVE SENSOR ROTOR

AT05751E01
  1. Using a snap ring expander, remove the snap ring.

  1. C212455
    Remove the sensor rotor and key.


15. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

D028705E01

NOTICE:
Do not turn the transmission over as this will contaminate the valve body with foreign matter located at the bottom of the pan.

  1. Remove the 19 bolts.

  1. Q007487E04
    Insert the blade of an oil pan seal cutter between the transmission case and the oil pan, and cut through the applied sealer.

    NOTICE:
    Be careful not to damage the oil pan and flange.

  1. Remove the pan by lifting the transmission case.


16. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

D001124E03
  1. Remove the magnets and use them to collect steel particles.

  1. Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

    1. Steel (magnetic): bearing, gear and clutch plate wear.
    2. Brass (non-magnetic): bush wear.


17. REMOVE VALVE BODY OIL STRAINER ASSEMBLY

D005550E01
  1. Remove the 4 bolts holding the oil strainer to the valve body.

  1. Remove the oil strainer and 5 gaskets.


18. REMOVE TRANSMISSION WIRE

D029778E04
  1. Disconnect the 4 connectors from the shift solenoid valves.

  1. Remove the bolt and stopper plate from the case.

  1. AT05066E01
    Pull out the transmission wire from the transmission case.

  1. Remove the O-ring from the transmission wire.


19. REMOVE TRANSMISSION VALVE BODY ASSEMBLY

D029011E01
  1. Remove the 20 bolts and valve body.


20. REMOVE CHECK BALL BODY

AT04847E01
  1. Remove the check ball body and spring.


21. REMOVE B-2 ACCUMULATOR PISTON

D006514E01
  1. Apply compressed air to the oil hole to remove the B-2 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.


22. REMOVE C-2 ACCUMULATOR PISTON

D006514E02
  1. Apply compressed air to the oil hole to remove the C-2 accumulator piston and 2 springs.

  1. Remove the 2 O-rings from the piston.


23. REMOVE B-0 ACCUMULATOR PISTON

D006515E01
  1. Apply compressed air to the oil hole to remove the B-0 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.


24. REMOVE C-0 ACCUMULATOR PISTON

D006516E01
  1. Apply compressed air to the oil hole to remove the C-0 accumulator piston and 2 springs.

  1. Remove the O-ring from the piston.


25. REMOVE PARKING LOCK PAWL BRACKET

AT05103E01
  1. Remove the 3 bolts and bracket.


26. REMOVE PARKING LOCK ROD

AT05120E01
  1. Disconnect the parking lock rod from the manual valve lever.


27. REMOVE PARKING LOCK PAWL SHAFT

Z006720E01
  1. Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.

  1. Remove the E-ring from the shaft.


28. REMOVE MANUAL VALVE LEVER SHAFT

Z006721E01
  1. Using a hammer and screwdriver, cut off the spacer and remove it from the shaft.

  1. AT05105E01
    Using a pin punch and hammer, tap out the spring pin.

    HINT:
    Slowly drive out the spring pin so that it does not fall into the transmission case.

  1. Pull out the manual valve lever shaft through the case, and remove the manual valve lever.


29. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

G034854E01
  1. Using a screwdriver, pry out the 2 oil seals.


30. REMOVE OIL PUMP ASSEMBLY

AT05122E01
  1. Stand up the transmission.

  1. Remove the 7 bolts from the transmission case.

  1. AT07874E03
    Using SST, remove the oil pump.
    SST
    09610-20012  

  1. Remove the O-ring from the oil pump.

  1. AT08431E01
    Remove the race from the oil pump.


31. REMOVE OVERDRIVE PLANETARY GEAR ASSEMBLY AND ONE-WAY CLUTCH ASSEMBLY

Q000619E01
  1. Remove the planetary gear, direct clutch and one-way clutch from the transmission case.

  1. AT03148E02
    Remove the race and assembled bearing and race.


32. REMOVE OVERDRIVE PLANETARY RING GEAR

AT05146E01
  1. Remove the ring gear from the transmission case.

  1. G035541E02
    Remove the assembled bearing and race and race from the overdrive planetary ring gear.


33. INSPECT OVERDRIVE BRAKE PISTON

AT05282E03
  1. Place SST and a dial indicator onto the overdrive brake piston.

    SST
    09350-30020   (09350-06120)

  1. AT05147E01
    Measure the stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).

    Standard piston stroke:
    1.75 to 2.05 mm (0.0689 to 0.0807 in.)

    If the piston stroke is not as specified, parts may have been assembled incorrectly. Check and reassemble again.
    If the piston stroke is still outside the standard, select another flange.

    HINT:
    There are 7 different thicknesses for the flange.

    Standard flange thickness:
    No.
    Specified Condition
    No.
    Specified Condition
    77
    3.3 mm (0.130 in.)
    81
    3.8 mm (0.150 in.)
    78
    3.5 mm (0.138 in.)
    82
    3.9 mm (0.154 in.)
    79
    3.6 mm (0.142 in.)
    83
    4.0 mm (0.157 in.)
    80
    3.7 mm (0.146 in.)
    -
    -


34. REMOVE OVERDRIVE BRAKE CLUTCH DISC

AT05109E01
  1. Using a screwdriver, pry out the snap ring.

  1. Q000637E04
    Remove the overdrive brake pack.


35. INSPECT PISTON STROKE OF 2ND COAST BRAKE

AT05216E01
  1. Using a waterproof pen, place a mark on the 2nd coast brake piston rod as shown in the illustration.

  1. AT05217E02
    Using SST, measure the piston stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).
    SST
    09240-00020  

    Standard piston stroke:
    1.5 to 3.0 mm (0.059 to 0.118 in.)

    If the stroke is not as specified, inspect the brake band.


36. REMOVE OVERDRIVE SUPPORT ASSEMBLY

AT05148E01
  1. Remove the 2 bolts holding the overdrive brake assembly to the case.

  1. AT05249E03
    Using SST, remove the snap ring.
    SST
    09350-30020   (09350-07060)

  1. AT05211E03
    Using SST, remove the overdrive brake assembly.
    SST
    09350-30020   (09350-07020)

  1. AT05110E05
    Remove the assembled bearing and race and the race from the overdrive brake assembly.


37. REMOVE 2ND COAST BRAKE PISTON ASSEMBLY

AT05127E01
  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07060)

  1. AT05280E01
    Apply compressed air to the oil hole to remove the 2nd coast brake cover, piston assembly and spring.

  1. Remove the 2 O-rings from the cover.


38. REMOVE DIRECT CLUTCH ASSEMBLY

AT05149E01
  1. Remove the direct clutch and forward clutch from the case.

  1. AT03149E01
    Remove the 2 bearings and races.


39. REMOVE FORWARD CLUTCH ASSEMBLY

AT05262E01
  1. Remove the direct clutch from the forward clutch.

  1. AT05259E03
    Remove the assembled bearing and race, thrust washer and race from the forward clutch.


40. REMOVE 2ND COAST BRAKE BAND

AT05111E01
  1. Using a screwdriver, pry out the E-ring from the pin.

  1. Q004030E01
    Remove the 2nd coast brake band from the case.


41. REMOVE FRONT PLANETARY RING GEAR

AT05128E01
  1. Remove the planetary ring gear from the case.

  1. Q000841E02
    Remove the assembled bearing and race, bearing and race from the planetary ring gear.

  1. Z005131E01
    With wooden blocks or equivalent under the output shaft, stand the transmission on the output shaft.


42. INSPECT FRONT PLANETARY RING GEAR

AT08187E01
  1. Using a dial indicator, measure the inside diameter of the planetary ring gear bush.

    Maximum inside diameter:
    24.65 mm (0.9705 in.)

    If the inside diameter is greater than the maximum, replace the planetary ring gear.


43. REMOVE FRONT PLANETARY GEAR

D029744E01
  1. Remove the race from the planetary gear.

  1. D029740E01
    Using SST, remove the snap ring.
    SST
    09350-30020   (09350-07070)

  1. D029741E01
    Remove the planetary gear from the case.

  1. D029742E01
    Using a screwdriver, remove the bearing and race from the planetary gear.


44. INSPECT FRONT PLANETARY PINION GEAR THRUST CLEARANCE

D029743E01
  1. Using a feeler gauge, measure the pinion gear thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.0079 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)

    If the clearance is greater than the maximum, replace the planetary gear.


45. REMOVE PLANETARY SUN GEAR ASSEMBLY AND ONE WAY CLUTCH ASSEMBLY

Q000837E01
  1. Remove the sun gear and one-way clutch from the case.

  1. Remove the thrust washer.


46. INSPECT PACK CLEARANCE OF 2ND BRAKE

AT05215E01
  1. Using a feeler gauge, measure the clearance between the snap ring and flange.

    Standard clearance:
    0.62 to 1.98 mm (0.0244 to 0.0780 in.)

    If the clearance is not as specified, inspect the discs.


47. REMOVE 1ST AND REVERSE BRAKE CLUTCH DISC

AT05476E01
  1. Using a screwdriver, pry out the snap ring.

  1. AT05398E01
    Remove the flange, plates and discs as a set.


48. INSPECT PACK CLEARANCE OF 1ST AND REVERSE BRAKE

AT08223E01
  1. Using a feeler gauge, measure the clearance between the plate and 2nd brake drum.

    Standard clearance:
    0.70 to 1.22 mm (0.0276 to 0.048 in.)

    If the clearance is not as specified, select another flange.

    HINT:
    There are 8 different thicknesses for the flange.

    Standard flange thickness:
    No.
    Specified Condition
    No.
    Specified Condition
    67
    5.4 mm (0.213 in.)
    52
    4.6 mm (0.181 in.)
    66
    5.2 mm (0.205 in.)
    53
    4.4 mm (0.173 in.)
    50
    5.0 mm (0.197 in.)
    54
    4.2 mm (0.165 in.)
    51
    4.8 mm (0.189 in.)
    55
    4.0 mm (0.157 in.)


49. REMOVE 2ND BRAKE PISTON SLEEVE

AT05279E01
  1. Using a screwdriver, remove the sleeve.


50. REMOVE REAR PLANETARY GEAR ASSEMBLY

AT05460E01
  1. Using SST and a screwdriver, remove the snap ring.

    SST
    09350-30020   (09350-07060)

  1. AT05158E01
    Remove the rear planetary, 2nd brake drum, 1st and reverse brake pack, No. 2 one-way clutch and output shaft.

  1. AT05132E01
    Remove the assembled thrust bearing and race from the case.

  1. AT08183E01
    Remove the 2nd brake drum.

  1. AT08208E01
    Remove the cushion plate, flange, plates and discs of the 1st and reverse brake.


51. REMOVE LEAF SPRING

AT05107E01

52. INSPECT 1ST AND REVERSE BRAKE CLUTCH DISC

AT06460E03
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


53. REMOVE BRAKE DRUM GASKET

AT04444E01

54. INSPECT PISTON STROKE OF 1ST AND REVERSE BRAKE

AT05258E01
  1. Make sure the 1st and reverse brake pistons move smoothly when applying and releasing compressed air into the transmission case.


55. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

AT08336E01
  1. Place SST on the 1st and reverse brake return spring, and compress the brake return spring.

    SST
    09350-30020   (09350-07050)

  1. Using SST, remove the snap ring and brake return spring.

    SST
    09350-30020   (09350-07070)

  1. Hold the No. 2 1st and reverse brake piston by hand, and apply compressed air to the transmission case to remove the No. 2 1st and reverse brake piston.


56. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

Q000777E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    12.9 mm (0.508 in.)

    If the length is not as specified, replace the spring sub-assembly.


57. REMOVE NO. 2 1ST AND REVERSE BRAKE PISTON

AT05375E01
  1. Hold the No. 2 1st and reverse brake piston and apply compressed air into the transmission case to remove the brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the O-ring from the brake piston.


58. REMOVE BRAKE REACTION SLEEVE

AT08335E01
  1. Using SST, remove the sleeve.

    SST
    09350-30020   (09350-07080)

  1. Remove the 2 O-rings from the sleeve.


59. REMOVE NO. 1 1ST AND REVERSE BRAKE PISTON

AT08334E01
  1. Using SST, remove the brake piston.

    SST
    09350-30020   (09350-07090)

  1. Remove the 2 O-rings from the brake piston.


60. INSPECT TRANSMISSION CASE BUSHING

AT08224E01
  1. Using a cylinder gauge, measure the inside diameter of the transmission case rear bush.

    Maximum inside diameter:
    38.19 mm (1.5035 in.)

    If the inside diameter is greater than the maximum, replace the transmission case.

← COMPONENTS (from Jun 2011)INSPECTION (from Jun 2011) →