2014 Hilux · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Aug 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012


1. BEARING POSITION

G035542E02

Bearing diameter:
Mark
Front Race Diameter
Inside / Outside
Thrust Bearing Diameter
Inside / Outside
Rear Race Diameter
Inside / Outside
A
28.45 mm (1.120 in.) / 47.3 mm (1.862 in.)
29.2 mm (1.15 in.) / 50.2 mm (1.976 in.)
-
B
28.6 mm (1.126 in.) / 46.4 mm (1.827 in.)
28.9 mm (1.138 in.) / 50.2 mm (1.976 in.)
-
C
33.0 mm (1.299 in.) /50.4 mm (1.984 in.)
31.4 mm (1.236 in.) / 49.4 mm (1.945 in.)
-
D
37.2 mm (1.465 in.) / 58.8 mm (2.315 in.)
33.8 mm (1.331 in.) / 50.0 mm (1.969 in.)
-
E
36.8 mm (1.449 in.) / 50.9 mm (2.004 in.)
33.7 mm (1.327 in.) / 47.6 mm (1.874 in.)
-
F
26.0 mm (1.024 in.) / 48.9 mm (1.925 in.)
26.0 mm (1.024 in.) / 42.8 mm (1.685 in.)
26.8 mm (1.055 in.) / 53.67 mm (2.113 in.)
G
-
49.9 mm (.1.965 in.) /64.4 mm (2.535 in.)
53.4 mm (2.102 in.) / 63.6 mm (2.504 in.)
H
33.7 mm (1.327 in.) / 47.6 mm (1.874 in.)
35.5 mm (1.398 in.) / 47.7 mm (1.878 in.)
-
I
28.5 mm (1.122 in.) / 44.2 mm (1.740 in.)
27.7 mm (1.091 in.) / 44.2 mm (1.740 in.)
-
J
-
39.38 mm (1.550 in.) / 58.1 mm (2.287 in.)
-


2. FIX TRANSMISSION CASE

AT05393E01
  1. Install the transmission case in the overhaul attachment.


3. INSTALL NO. 1 1ST AND REVERSE BRAKE PISTON

AT08209E03
  1. Coat 2 new O-rings with ATF.

  1. Install the 2 O-rings on the No. 1 brake piston.

  1. Install the No. 1 brake piston to the reaction sleeve.


4. INSTALL BRAKE REACTION SLEEVE

D001243E02
  1. Coat a new O-ring with ATF, and install it to the reaction sleeve.

  1. With the No. 1 brake piston underneath (the rear side), install the brake reaction sleeve and No. 1 brake piston to the transmission case.

    NOTICE:
    Be careful not to damage the O-rings.


5. INSTALL NO. 2 1ST AND REVERSE BRAKE PISTON

AT08333E02
  1. Coat a new O-ring with ATF.

  1. Install the O-ring on brake piston.

  1. With the spring seat of the piston facing upward (the front side), place the piston in the transmission case.

    NOTICE:
    Be careful not to damage the O-ring.


6. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

AT05429E01
  1. Place the No. 2 brake return spring onto the brake piston.

  1. AT08303E01
    Place SST on the brake return spring, and compress the brae return spring.
    SST
    09350-30020   (09350-07050)

  1. Using SST, install the snap ring. Make sure the end gap of the snap ring is not aligned with the spring retainer claw.

    SST
    09350-30020   (09350-07070)


7. INSPECT PISTON STROKE OF 1ST AND REVERSE BRAKE

AT05258E02
  1. Make sure the 1st and reverse brake pistons move smoothly when compressed air is applied into the transmission case.


8. INSTALL LEAF SPRING

AT05107E01

9. INSTALL REAR PLANETARY GEAR ASSEMBLY
  1. Install the flange with the rounded edge facing upward.

  1. C238611E02
    for 1KD-FTV:
    Install the 7 discs and 7 plates.

    Install in order:
    F - D - P - D - P - D - P - D - P - D - P - D - P - D - P

    HINT:
    F = Flange
    P = Plate
    D = Disc

  1. C273606E01
    for 2KD-FTV:
    Install the 6 discs and 6 plates.

    Install in order:
    F - D - P - D - P - D - P - D - P - D - P - D - P

    HINT:
    F = Flange
    P = Plate
    D = Disc

  1. Z005138E01
    Coat the assembled bearing and race with petroleum jelly, and install it onto the case.

    Assembled bearing and race diameter:
    Item
    Inside
    Outside
    Assembled bearing and race
    39.38 mm (1.550 in.)
    58.1 mm (2.287 in.)

    NOTICE:
    Be careful of the installation direction of the assembled bearing and race.

  1. AT07893E01
    Align the teeth on the flange, discs and plates.

  1. Q004066E01
    Face the snap ring upward (front side), and install the 2nd brake drum to the planetary gear.

    NOTICE:
    Face the oil hole in the drum towards the lower side of the transmission case (the side where the valve body is installed).

  1. Q004068E01
    Align the splines of the transmission case with the assembled rear planetary gear and 1st and reverse brake with the output shaft, indicated by A.

  1. AT05158E01
    Install the assembled output shaft.

  1. Z005131E01
    Reset the output shaft on wooden blocks.

  1. AT05396E01
    Using SST, Install the snap ring.
    SST
    09350-30020   (09350-07060)


10. INSPECT PACK CLEARANCE OF 1ST AND REVERSE BRAKE

AT08223E01
  1. Using a feeler gauge, measure the clearance between the plate and 2nd brake drum.

    Clearance:
    0.70 to 1.22 mm (0.0276 to 0.048 in.)

    HINT:
    1. If the clearance is not as specified, select another flange.
    2. There are 8 different thicknesses for the flange.

    Flange thickness: 
    No.
    Thickness
    No.
    Thickness
    67
    5.4mm (0.213 in.)
    52
    4.6 mm (0.181 in.)
    66
    5.2 mm (0.205 in.)
    53
    4.4 mm (0.173 in.)
    50
    5.0 mm (0.197 in.)
    54
    4.2 mm (0.165 in.)
    51
    4.8 mm (0.189 in.)
    55
    4.0 mm (0.157 in.)


11. INSTALL 2ND BRAKE PISTON SLEEVE

AT05397E01

12. INSTALL BRAKE DRUM GASKET

AT04469E01
  1. Coat a new gasket with ATF, and install the brake drum gasket.


13. INSTALL NO. 1 ONE-WAY CLUTCH

AT05231E01
  1. Install the thrust washer onto the 2nd brake piston sleeve.

  1. Z005133E01
    Install the No. 1 one-way clutch as shown in the illustration.


14. INSTALL 1ST AND REVERSE BRAKE CLUTCH DISC

AT05398E02
  1. Install the 1.8 mm (0.071 in.) thick plate with the rounded edge side of the plate facing the disc.

  1. Install the flange, 5 plates and 5 discs.

    Install in order:
    P - D - P - D - P - D - P - D - P - D - F

    HINT:
    F = Flange
    P = Plate
    D = Disc

  1. AT05476E01
    Using a screwdriver, install the snap ring.


15. INSPECT PACK CLEARANCE OF 2ND BRAKE

AT05215E01
  1. Using a feeler gauge, measure the clearance between the snap ring and flange.

    Clearance:
    0.62 to 1.98 mm (0.0244 to 0.0780 in.)

    If the clearance is not as specified, inspect the discs.


16. INSTALL PLANETARY SUN GEAR ASSEMBLY AND ONE-WAY CLUTCH ASSEMBLY

Q000840E01
  1. While turning the sun gear clockwise, install it into the one-way clutch.

    HINT:
    Confirm that the thrust washer is installed correctly.


17. INSTALL FRONT PLANETARY GEAR

D029745E01
  1. Coat the bearing and race with petroleum jelly, and install them onto the planetary gear.

    Bearing and race diameter:
    Item
    Inside
    Outside
    Bearing
    35.5 mm (1.398 in.)
    47.7 mm (1.878 in.)
    Race
    33.7 mm (1.327 in.)
    47.6 mm (1.874 in.)

    NOTICE:
    Be careful of the installation direction of the bearing and race.

  1. D029741E01
    Install the planetary gear to the sun gear input drum.

  1. D029740E01
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07070)

  1. Remove the wooden blocks under the output shaft.

  1. D029744E01
    Coat the race with petroleum jelly, and install it onto the planetary gear.

    Race diameter:
    Item
    Inside
    Outside
    Race
    53.4 mm (2.102 in.)
    63.6 mm (2.504 in.)

    NOTICE:
    Be careful to the installation direction of the race.


18. INSTALL 2ND COAST BRAKE BAND

Q004030E01
  1. Install the brake band to the case.

  1. Q000788E01
    Install the E-ring to the pin.

  1. Install the pin through the brake band.


19. INSTALL DIRECT CLUTCH ASSEMBLY

D006214E03
  1. Install the assembled bearing and race and thrust washer to the forward clutch.

  1. AT05262E01
    Install the direct clutch to the forward clutch.


20. INSTALL FRONT PLANETARY RING GEAR

Z005137E01
  1. Coat the race with petroleum jelly, and install them onto the forward clutch.

    Bearing and race diameter:
    Item
    Inside
    Outside
    Bearing
    26.0 mm (1.024 in.)
    42.8 mm (1.685 in.)
    Race
    26.0 mm (1.024 in.)
    48.9 mm (1.925 in.)

    NOTICE:
    Be careful of the installation direction of the bearing and race.

  1. Z005136E01
    Coat the race with petroleum jelly, and install it onto the front planetary ring gear.

    Race diameter:
    Item
    Inside
    Outside
    Race
    26.8 mm (1.055 in.)
    53.67 mm (2.113 in.)

    NOTICE:
    Be careful of the installation direction of the race.

  1. AT05432E01
    Align the flukes of the discs in the forward clutch.

  1. Q000838E01
    Align the splines of the planetary ring gear with the flukes of the discs and install the planetary ring gear to the forward clutch.


21. INSTALL FORWARD CLUTCH ASSEMBLY

AT08306E01
  1. Coat the bearing and race with petroleum jelly, and install them onto the ring gear.

    Bearing and race diameter:
    Item
    Inside
    Outside
    Bearing
    49.9 mm (1.965 in.)
    64.4 mm (2.535 in.)
    Race
    53.4 mm (2.102 in.)
    63.6 mm (2.504 in.)

    NOTICE:
    Be careful of the installation direction of the bearing and race.

  1. AT08234E01
    Install the assembled direct clutch, forward clutch and front planetary ring gear into the transmission case.

  1. AT05213E01
    Using a vernier caliper, measure the distance between the sun gear input drum and direct clutch drum as shown in the illustration.

    Distance:
    5.3 to 7.3 mm (0.209 to 0.287 in.)

    If the distance is not as specified, check for an improper installation.

  1. Z005236E01
    Coat the assembled bearing and race with petroleum jelly and install it onto the forward clutch.

    Assembled bearing and race diameter:
    Item
    Inside
    Outside
    Assembled bearing and race
    33.7 mm (1.327 in.)
    47.6 mm (1.874 in.)

    NOTICE:
    Be careful of the installation direction of the assembled bearing and race.


22. INSTALL 2ND COAST BRAKE PISTON ASSEMBLY

AT05086E01
  1. Coat 2 new O-rings with ATF, and install them to the cover.

  1. Install the spring, the piston assembly and cover to the case.

  1. AT05127E01
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07060)


23. INSPECT PISTON STROKE OF 2ND COAST BRAKE

AT05216E01
  1. Place a mark on the 2nd coast brake piston rod.

  1. AT05217E01
    Using SST, measure the stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).
    SST
    09240-00020  
    If the stroke is not as specified, replace the brake band with a new one.


24. INSTALL OVERDRIVE BRAKE ASSEMBLY

AT05110E01
  1. Coat the assembled bearing and race and race with petroleum jelly, and install it onto the overdrive brake assembly.

    Assembled bearing and race and race diameter:
    Item
    Inside
    Outside
    Race
    36.8 mm (1.449 in.)
    50.9 mm (2.004 in.)
    Assembled bearing and race
    33.8 mm (1.331 in.)
    50.0 mm (1.969 in.)

    NOTICE:
    Be careful of the installation direction of the assembled bearing and race and race.

  1. AT05159E01
    Confirm that the thrust washer is installed correctly.

    HINT:
    Make sure that the tab of the washer fits into the hole on the overdrive brake assembly.

  1. AT05400E01
    Using 2 bolts of SST, aim the bolt and oil holes of the overdrive rake assembly toward the valve body side, and align them with the bolt holes of the transmission case. Insert the overdrive brake assembly.
    SST
    09350-30020   (09350-07020)

  1. Temporarily tighten the 2 bolts.

  1. Q000618E01
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07060)

    HINT:
    Install the snap ring open end toward the valve body.

  1. AT05218E01
    Tighten the 2 bolts.

    Torque:
    25 N*m{ 260 kgf*cm , 19 ft.*lbf }


25. INSPECT OUTPUT SHAFT

Z006796E01
  1. Using a dial indicator, measure the end play of the output shaft with hand.

    End play:
    0.30 to 1.04 mm (0.0118 to 0.0409 in.)

    If the end play is not as specified, check for an improper installation.

  1. Check that the output shaft rotates smoothly.


26. INSTALL OVERDRIVE BRAKE CLUTCH DISC

Q000637E01
  1. Install the 4.0 mm (0.157 in.) thick flange (flat ring) with the rounded edge side of the flange facing the discs.

  1. Install the 5 plates, 5 discs and flange.

    Install in order:
    P - D - P - D - P - D - P - D - P - D - F

    HINT:
    F = Flange
    P = Plate
    D = Disc

  1. AT05233E01
    Using a screwdriver, install the snap ring.


27. INSPECT OVERDRIVE BRAKE PISTON

AT05282E01
  1. Place SST and a dial indicator onto the overdrive brake piston.

    SST
    09350-30020   (09350-06120)

  1. AT05147E01
    Measure the stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).

    Piston stroke:
    1.75 to 2.05 mm (0.0689 to 0.0807 in.)

    If the piston stroke is not as specified, parts may have been assembled incorrectly. Check and reassemble again.

    HINT:
    1. If the piston stroke is still outside the standard, select another flange.
    2. There are 7 different thicknesses for the flange.

    Flange thickness: 
    No.
    Thickness
    No.
    Thickness
    77
    3.3 mm (0.130 in.)
    81
    3.8 mm (0.150 in.)
    78
    3.5 mm (0.138 in.)
    82
    3.9 mm (0.154 in.)
    79
    3.6 mm (0.142 in.)
    83
    4.0 mm (0.157 in.)
    80
    3.7 mm (0.146 in.)



28. INSTALL OVERDRIVE PLANETARY RING GEAR

Q000842E01
  1. Coat the race with petroleum jelly, and install it onto the overdrive brake assembly.

    Race diameter:
    Item
    Inside
    Outside
    Race
    37.2 mm (1.465 in.)
    58.8 mm (2.315 in.)

    NOTICE:
    Be careful of the installation direction of the race.

  1. AT05146E01
    Install the ring gear.

  1. G035543E02
    Coat the assembled bearing and race with petroleum jelly, and install them onto the ring gear.

    Assembled bearing and race diameter:
    Item
    Inside
    Outside
    Assembled bearing and race
    31.4 mm (1.236 in.)
    49.4 mm (1.945 in.)

    NOTICE:
    Be careful of the installation direction of the assembled bearing and race.

  1. Z005128E01
    Coat the race with petroleum jelly, and install it onto the planetary gear.

    Race diameter:
    Item
    Inside
    Outside
    Race
    24.7 mm (0.972 in.)
    41.8 mm (1.646 in.)

    NOTICE:
    Be careful of the installation direction of the race.

  1. Q000619E01
    Install the overdrive planetary gear, overdrive direct clutch and one-way clutch.

  1. AT04470E01
    Place SST on the transmission case.
    SST
    09350-36010   (09350-06090)

  1. Using a vernier caliper, measure the distance between the top of SST and clutch drum.

    Standard distance:
    15.5 to 16.5 mm (0.610 to 0.650 in.)

    If the distance is not as specified, check for an improper installation.

  1. AT08313E01
    Coat the assembled bearing and race with petroleum jelly, and install it onto the overdrive direct clutch.

    Assembled bearing and race diameter:
    Item
    Inside
    Outside
    Assembled bearing and race
    29.2 mm (1.150 in.)
    50.2 mm (1.976 in.)

    NOTICE:
    Be careful of the installation direction of the assembled bearing and race.


29. INSTALL OIL PUMP ASSEMBLY

Z005237E01
  1. Coat the race with petroleum jelly, and install it onto the oil pump.

    Race diameter:
    Item
    Inside
    Outside
    Race
    28.45 mm (1.120 in.)
    47.3 mm (1.862 in.)

    NOTICE:
    Be careful of the installation direction of the race.

  1. Coat a new O-ring with ATF, and install it around the pump body.

  1. Place the oil pump through the input shaft, and align the bolt holes of the pump body with the transmission case.

  1. Hold the input shaft, and lightly press the oil pump body to slide the oil seal rings into the overdrive direct clutch drum.

    NOTICE:
    Do not forcefully push on the oil pump as the oil seal ring will stick to the direct clutch drum.

  1. AT05404E01
    Install the 7 bolts.

    Torque:
    22 N*m{ 220 kgf*cm , 16 ft.*lbf }


30. INSPECT INPUT SHAFT SUB-ASSEMBLY

AT05244E01
  1. Make sure the input shaft rotates smoothly.


31. INSTALL TRANSMISSION CASE PLUG

D005553E01
  1. Coat a new O-ring with ATF, and install it to the plug.

  1. Install the plug to the case with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


32. INSPECT INDIVIDUAL PISTON OPERATION

AT05275E05
  1. Check the operating sound while applying compressed air into the oil hole indicated in the illustration.

    HINT:
    When inspecting the overdrive direct clutch, check with the C-0 accumulator piston hole closed.
    If there is no sound, disassemble and check the parts installation condition.


    1. Overdrive direct clutch (C1)

    2. Direct clutch (C2)

    3. Forward clutch (C3)

    4. Overdrive brake (B1)

    5. 2nd coast brake (B2)

    6. 2nd brake (B3)

    7. 1st and reverse brake (B4)


33. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

AT05238E01
  1. Using SST and a hammer, tap in 2 new oil seals.

    SST
    09350-30020   (09350-07110)


34. INSTALL MANUAL VALVE LEVER SHAFT

Q000775E01
  1. Install a new spacer to the manual valve lever.

  1. Install the manual valve lever shaft to the transmission case through the manual valve lever.

  1. AT05405E01
    Using a hammer, tap in a new spring pin.

  1. D006523E01
    Align the manual valve lever indentation with the spacer hole, and stake them with the punch.

  1. Make sure that the shaft rotates smoothly.


35. INSTALL PARKING LOCK PAWL SHAFT

Q000776E04
  1. Install the E-ring to the shaft.

  1. Install the parking lock pawl, shaft and spring.


36. INSTALL PARKING LOCK ROD

Z006797E01
  1. Connect the parking lock rod to the manual valve lever.


37. INSTALL PARKING LOCK PAWL BRACKET

AT05406E01
  1. Place the parking lock pawl bracket onto the transmission case and install the 3 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }

  1. Z005222E01
    Shift the manual valve lever to the P position, and confirm that the planetary ring gear is correctly locked up by the lock pawl.


38. INSTALL C-0 ACCUMULATOR PISTON

AT05010E01
  1. Coat a new O-ring with ATF, and install it to the piston.

  1. D028075E01
    Install the 2 springs and accumulator piston to the hole.

    C-0 accumulator spring:
    Inner spring:
    Free Length
    Outer Diameter
    Color
    51.5 mm (2.028 in.)
    14.02 mm (0.552 in.)
    Red
    Outer spring:
    Free Length
    Outer Diameter
    Color
    79.9 mm (3.146 in.)
    20.9 mm (0.823 in.)
    Light Blue


39. INSTALL B-0 ACCUMULATOR PISTON

AT05010E01
  1. Coat 2 new O-rings with ATF, and install them to the piston.

  1. D028074E01
    Install the spring and accumulator piston to the hole.

    B-0 accumulator spring:
    Free Length
    Outer Diameter
    Color
    62.0 mm (2.441 in.)
    16.0 mm (0.630 in.)
    Green


40. INSTALL C-2 ACCUMULATOR PISTON

AT05010E01
  1. Coat 2 new O-rings with ATF, and install them to the piston.

  1. D028073E01
    Install the 2 springs and accumulator piston to the hole.

    C-2 accumulator spring:
    Inner spring:
    Free Length
    Outer Diameter
    Color
    42.1 mm (1.657 in.)
    14.7 mm (0.579 in.)
    Pink
    Outer spring:
    Free Length
    Outer Diameter
    Color
    68.53 mm (2.698 in.)
    20.2 mm (0.795 in.)
    Blue


41. INSTALL B-2 ACCUMULATOR PISTON

AT05010E01
  1. Coat 2 new O-rings with ATF, and install them to the piston.

  1. D028072E01
    Install the spring and accumulator piston to the hole.

    B-2 accumulator spring:
    Free Length
    Outer Diameter
    Color
    70.5 mm (2.776 in.)
    19.9 mm (0.784 in.)
    Light Grey


42. INSTALL CHECK BALL BODY

AT05098E01
  1. Install the spring and check ball body.


43. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

AT08393E01
  1. Align the groove of the manual with the pin of the lever.

  1. D029011E02
    Install the 20 bolts.

    Torque:
    10 N*m{ 100 kgf*cm , 7 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    Bolt length:
    23 mm (0.91 in.) for A
    28 mm (1.10 in.) for B
    36 mm (1.42 in.) for C


44. INSTALL TRANSMISSION WIRE

AT05066E02
  1. Coat a new O-ring with ATF, and install it to the transmission wire.

  1. Install the transmission wire to the case, and install the stopper plate with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. D029778E01
    Connect the connectors to the shift solenoid valves.


45. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

Z007979E01
  1. Using a plastic-faced hammer, install the pipe as shown in the illustration.

    NOTICE:
    Be careful not to bend or damage the pipe.

  1. D005554E01
    Install 5 new gaskets on the oil strainer.

  1. D028706E01
    Install the oil strainer with the 4 bolts.

    Torque:
    10 N*m{ 100 kgf*cm , 7 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    Bolt length:
    14 mm (0.55 in.) for A
    20 mm (0.79 in.) for B
    23 mm (0.91 in.) for C


46. INSTALL OIL CLEANER MAGNET

D029014E01
  1. Install the 3 magnets.


47. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

AT01362E05
  1. Remove any FIPG material.

    NOTICE:
    Be careful not to drop oil on the contacting surfaces of the transmission case and oil pan.

  1. Apply FIPG to the oil pan.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. D028705E01
    Install the oil pan with the 19 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


48. INSTALL SENSOR ROTOR

C273604E01
  1. Install the key on the output shaft.

  1. Align the groove of the sensor rotor with the key, and install the sensor rotor.

  1. AT05751E01
    Using snap ring pliers, install the snap ring.


49. INSTALL TRANSFER CASE ADAPTER REAR OIL SEAL

D029795E01
  1. Using SST and a hammer, install a new oil seal.

    SST
    09950-60010   (09951-00560)
    09950-70010   (09951-07150)


50. INSTALL TRANSFER ADAPTER REAR

D028071E02
  1. Install the rear adaptor transfer and gasket.

  1. Install the 8 bolts.

    Torque:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    Bolt length:
    50 mm (1.969 in.) for A
    40 mm (1.575 in.) for B


51. INSTALL AUTOMATIC TRANSMISSION HOUSING

D028078E01
  1. Clean the threads of the bolts and case with white gasoline.

  1. Apply adhesive or equivalent to the 6 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the transmission housing with the 6 bolts.

    Torque:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf } for 14 mm bolt
    57 N*m{ 580 kgf*cm , 42 ft.*lbf } for 17 mm bolt


52. INSTALL NO. 2 VEHICLE SPEED SENSOR

G035550E01
  1. Install a new O-ring to the sensor.

  1. Install the sensor with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


53. INSTALL OVERDRIVE DIRECT CLUTCH SPEED SENSOR

Q003894E01
  1. Install a new O-ring to the sensor.

  1. Install the speed sensor with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


54. INSTALL OIL COOLER TUBE UNION

Q003892E01
  1. Coat 2 new O-rings with ATF, and install them to each tube union.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }


55. INSTALL AUTOMATIC TRANSMISSION FLUID TEMPERATURE SENSOR

Q003891E01
  1. Coat a new O-ring with ATF, and install it to the sensor.

  1. Install the sensor.

    Torque:
    24 N*m{ 250 kgf*cm , 18 ft.*lbf }


56. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

HINT:
Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.

  1. G034858E01
    Install the park/neutral position switch onto the manual valve lever shaft, and temporarily install the adjusting bolt.

  1. Install the grommet and a new lock washer. Install and torque the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. D028682E01
    Push the control shaft rearward as much as possible.

  1. Return the control shaft lever 2 notches to the N position.

  1. D006517E01
    Align the neutral basic line with the switch groove, as shown in the illustration, and tighten the adjusting bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

    HINT:
    Bend at least 2 of the lock washer tabs.


57. INSTALL TRANSMISSION CONTROL SHAFT LEVER LH

D028070E02
  1. Install the control shaft lever with the washer and nut.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }


58. INSTALL BREATHER HOSE

C115790E01
  1. Install the breather hose.


59. INSTALL DRAIN PLUG SUB-ASSEMBLY

Torque:
20 N*m{ 205 kgf*cm , 15 ft.*lbf }

← REASSEMBLY (Jun 2011 – Jul 2012)COMPONENTS (from Jun 2011) →